Ford Escape / Hybrid :: 2005 2.3L - Loss Of Power / Struggles On Hills
Aug 12, 2014
So my wife's 2005 escape has been slowly losing power over the past 6 months or so. I regularly change the oil, tried new spark plugs, new air filter and still it's lazy. I know it's not a race machine but it struggles on hills.
This winter it was having problems starting unless the accelerator was pushed to the floor. After a cleaning of the Idle control valve all was well again. It has roughly 72,000 miles on it and uses .5-1qt of oil between changes.
View 2 Replies
Advertisement
My escape struggles to reach 30 mph.. throttle position sensor code when scanned.Replaced the sensor but still barely any power check engine light hasnt come back on.
View 9 Replies
I have a 2004 Ford Escape XLT V6 and I am experiencing a major loss of power in the vehicle. It idles smooth at about 1000rpm's but when you drive it , the vehicle won't go over 30mph and has a significant miss to it. I replaced the fuel filter, put in some Seafoam and took it for a drive and it still did not have any power and I blew out the EGR valve on the test drive. I replaced the EGR valve and the problem still remains. I hooked up a handheld computer to it and I got a P0300, P0304, P0305, P0306, P0316 and a P0355 error codes.
View 1 Replies
So heres the story..........'02 Escape, 179K miles, just had the oil changed 2 weeks ago, ever since then I've smelled oil burning when the car starts up and every now and then after exiting the car. Also have had the check engine light on intermittently for the EGR insufficient flow for the past few months. It comes and goes whenever it wants. Today Wifey called me and said something was wrong with the car, I drove it home (about 26 miles). The car runs fine as shifts through the gears, but as soon as it gets a load put on it, it cant pull hard like it used to and it gets a high pitched/squealy whistle similar to a turbo that's spooled up.
Its hard to say where its coming from but from what I can tell I'd say somewhere under the hood near the glove box. (that's the only way I can think of to describe it). There's a big long hill right outside her work that I wasn't sure I was gonna make it up. Car just didn't have any power and couldn't decide what gear to be in as RPMs were too high in a lower gear but wouldn't pull in the higher gear. Car pulls hard off the bottom but falls flat in the midrange. I was thinking maybe clogged cat but what would the whistling sound be?
View 14 Replies
We are a 2 Escape family. We have an '03 and an '05 - both 4WD and 3.0 V6. My college freshman son purchased the '05 this summer to get to and from his summer job. It has a little over 173K on the clock and it has a power steering leak, so I decided to try to tackle this one.
There is a fairly good video on YouTube on replacement of the power steering pump on an '03 - but apparently on the '05 Ford decided to relocate the pump from under the upper right engine mount to a lower location closer to the front bumper so the video is not of much use in this case.
I have searched the web and this site but cannot find any tips or instructions to replace the power steering pump on the '05. The Chilton Manual I have does not acknowledge the difference in the power steering pump location on the '05 and only provides the procedure for those Escapes where the pump is located under the upper engine mount.
I think I may be able to get better access by removing the inner fender plastic and perhaps the front bumper cover, but would really like to know the accepted procedure before I start tearing into this one.
One interesting bit of info regarding power steering fluid on these vehicles. Ford designed them to use automatic transmission fluid (Mercon) instead of power steering fluid. Initially, when I saw the leak, I thought it was a tranny line leak. Then I traced it to the front of the engine which is totally on the opposite side of the vehicle from the tranny lines.
View 14 Replies
A couple weeks ago I had to have both lower ball joints replaced on my '01 XLS 4WD with the 6 cylinder engine. The garage's alignment machine was on the blink, so the mechanic told me to it woudl be fine to drive, and to bring it back this week when the machine was fixed.
The Escape seemed to drive fine until today, coming home from work, the Escape veered slightly to the right, and there was a brief sensation in the steering wheel as if it had been disconnected, as if something slipped. Then the steering was back, and although I was tracking straight down the highway, I noticed the steering wheel was turned to the left. It seemed to steer fine, although I had slowed way down.
View 4 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
Getting DTC P0401 on my 2011 with 92K miles. First time I got the CEL, we were on vacation, so I read the code, took a screen shot, then cleared it. Called my normal dealer, setup an appt, verified that they thought the truck was safe to drive. Coming home from vacation, I was pulling the TT in my sig, and noticed significant loss of power on hills that I have pulled many times before that I couldnt even hold 55 on now. Transmission dropped into 4th a couple times, on hills that it would sometimes stay in 6th, or at most drop to 5th.
CEL stayed off for a week , and came back on again. The funny thing is that after a day or 2, the CEL went back out on its own. I read the codes the P0401 is still there as a stored code(I did not clear this time). Around town the truck drives fine, the only thing I noticed was the decrease in power when towing. Truck is at the dealer now. TECH "isn't convinced" yet that there is a problem. He is not finished diagnosing yet, and I am sure that he has specific tests to run, but I am starting to fear that I will be getting the call to come get my truck.
View 6 Replies
I pulled with my 2000 F250 7.3 for the first time yesterday pulling a 12,500 5th wheel and then again today with an 18 ft ski boat weighting around 3500 for both the trailer and boat. I had this same issue pulling both.
Today when pulling the boat/trailer i was behind a slow moving truck and when we hit a hill with a passing lane i merged over and wanted to start passing him. We started off at around 45 mph up the hill and as I started pushing the pedal I wasn't gaining any speed and my rpm's didn't even get over 1500. It felt like a stall and continued that at around 45-50 mph up the hill (about a 65 degree slope). When I'm not towing the truck runs great, plenty of power and averaging around 16 1/2 mpg.
Only mods i have is a 6647 Napa filter, muffler delete and it's running the same 4 position TS tuner from the original owner. During normal operation I run it at the 75hp gain and when towing i use the 50hp gain.
In both instances i could see black smoke coming from exhaust when pushing the pedal but my rpm's wouldn't go up and truck maintained the slow speed going up the hill. Once at the top it drove normal and picked up speed without any problems.
View 14 Replies
My 2000 Corolla has been a dog from the day I bought it, a few years ago. It struggles up hills or speeding up on the highway. I took it to a local garage and was told that one of the cylinders was fouling a spark plug with oil. The owner said the cylinder would need to be machined to correct the problem. The total cost of repairs would be about $1800. My question is, would I be better off purchasing a rehabbed cylinder and having him put it in? Is this even possible? BTW, the car only has 132k miles on it, which is not a lot for a Corolla.
View 16 Replies
The past couple days when driving to school in the morning i've been noticing that my car starts to rattle and struggles to accelerate once I pull out of my driveway. Once i get to the next stop sign to take off the car runs fine like nothing ever happened. My check engine light doesn't come on though. I usually let the car sit for about 30 seconds to a minute before i start to move the car. Mods I have are Unitronic stage 2, Forge 007p DV with yellow spring, and 3" downpipe.
View 1 Replies
I have a 2000 Ford Explorer with 188,000 miles on it. I bought it used with 110K miles and put a new tranny in at that time. Now, I am having problems. I don't know if it's the tranny or the engine. It looses power when climbing hills. It takes off really slow with no power and finally gets up to speed it switches gears the whole time smoothly but the engine just can't take a load.
The check engine light came on and put out 10 codes:
P1451 EVAP Control System Canister Vent
P1747 Electronic Solenoid A-Short Circuit
P0743-Torque Converter Clutch Circuit Electrical
P0750-Shift Solenoid "A"
P0755-Shift Solenoid "B"
P0760-Shift Solenoid "C"
P0765-Shift Solenoid "D"
P0135-O2 Sensor Heater Circuit
P0155-O2 Sensor Heater Circuit
P1409-EGR Vacuum Regulator Circuit Malfunction
Those are the codes and I don't know how one has anything to do with the other. I checked the dip stick on the tranny and it's clean. Juicy red and not shavings.
View 4 Replies
2003 f550 with 7.3, suddenly loses power and struggles while driving. White/blue smoke comes from tailpipe, can smell the diesel exhaust bad when happens, comes and goes intermittently but has been happening more and more often. I uploaded a video onto YouTube to show sound, rough running motor and smoke from exhaust although smoke not that bad in video. Search "shadetreelandscaping" on YouTube in case link below doesn't work.
ShadeTreeLandscaping - YouTube
Took to ford dealer a few diff times for problem and they can't get any codes, can't duplicate problem. After it being in for third time they say had to call ford tech hotline and they suggest replacing injector however can not and will not gaurntee that will solve problem, and obviously dealer isn't cheap for repair. I find it hard to believe that a bad injector(s) would be an intermittent problem as it is or that it would cause fuel pump to make gurgling sound.
View 13 Replies
I only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 Replies
My 2.4L 03 XLE with 220k on it is losing power. Running fine other than not accelerating or going up hills as well as it was last week. I have P420 cat code for the past 40K. It also has the typical smoky start from leaking valve seals and uses about a quart every 1k miles.
Ran a can of 44k through it and I'm about to pull the plugs and see what shape they are in, but I'm wondering if this loss of power might be the cat. I've been searching and it seems a plugged cat is a common cause for power loss. Seems likely since I use so much oil.
Seen the DIY replacement and leaky seals Rockauto suggested replacement Eastern ECOIII as well as the Walker.
View 14 Replies
I have a 2005 Escape Hybrid. Last summer, the A/C went out, so when in the fall I finally got around to having the cooling system flushed. Did the trick, and A/C works fine. Now that winter's come along, I've noticed an issue with the heat. All fan speeds work correctly, and the dash controls for heat and cold work properly. But what's odd is that I get plenty of heat when the vehicle is at speed, above about 30 mph. As soon as I slow down below that, or hit a red light, there's no heat. The blower just blows cold air until I am back up at speed again.
View 9 Replies
I have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
View 2 Replies
2005 Ford Escape XLT (4WD) (non-Hybrid). Our Escape had uneven wear on the front tires. Because the mechanic we've used over the year we've lived here doesn't do alignments, my wife took it to a chain tire place on a Sunday afternoon because they were open. He said the ball joint was bad, so he wouldn't do an alignment and because they were super-busy and short-handed, he asked if we could bring it back during the week for an estimate.
A couple of weeks later I called my guy, who recommended a shop a few blocks over who does alignments, so we took it to him. We told him that the chain store had said about the ball joint. I'm pretty sure that before we took it to him, the car had started occasionally started jerking a bit in a curve, but it's been a couple of months and I only know for certain it was doing it after. (I'm not certain if it was doing it before because my wife was mostly driving that vehicle, then)
The first time it was in his shop, the mechanic said it wasn't the ball joint, but the tie-rod. After fixing that, he sold us a couple of tires and aligned the vehicle. On the way home is when I know I was aware of the car jerking a bit in curves. I'm pretty sure it was jerking in the direction of the curve, but again, it's been a couple of months.
Took it back to him the next day and though we suggested he test drive in one direction which had multiple curves, he said he retightened the tie-rod because one side wasn't right, ran it through alignment again and test drove it in another direction which only had one s-curve.
I want to say it was better for a while, but I can't really swear that to be the case. We've long had an ABS light which our previous mechanic in another part of the country said was the sensor. I had forgotten, but the first mechanic we used here had broken the axle and replaced it at no charge, when he was replacing the alternator.
The alignment mechanic said that we had a bad tone ring and the easiest thing to do would be to replace the axle. A week or so later, I called him and said we were ready to do the brakes, but I have one car and he does many and I wasn't really clear, instead of doing anything with the axle or the tone ring, his shop replaced the brakes.
Somewhere around this time, the vehicle started occasionally jerking to the left. Not in a curve, but in the straightways and the best we can tell, it's mostly when we're accelerating and is most noticeable between 30 & 45 MPH. This may not be entirely true, but it's true enough that we believe it. The "jerk" sort of feels like a car driving through fresh snow "falling" into a rut. It also sort of feels what I imagine a faulty ball joint might feel like.
While it was still more of a minor issue -- it happened more rarely than it's happening now -- we took it to what I'd consider our regular mechanic and got him to replace the axle. I didn't actually say anything to him about the jerking because it was still too occasional and I was hoping it was related to the tone ring. It's now gotten progressively worse and I'm at a loss for diagnosis. You'd think that if it was the ball joint, between the two alignments, the brake job, tire replacement and rotation and getting a new axle, one of the mechanics would have noticed it.
Compounding the issue is the fact that there's two (or three if you count the first guy, four if you count the chain tire place) garages involved. Also, I've done some of the engine work my regular mechanic recommended, so there could be a thing about me getting them to diagnose and then doing the work myself or the one mechanic replacing the axle like the alignment guy had suggested. Who knows. We haven't lived here long, so there's not really a lot of history. All I know is that they all get good Yelp reviews.
Also should probably be factored... the alignment mechanic said he felt vibration around 45 MPH and because didn't think we use the 4WD, he said he disconnected the drive shaft from the CV joint (or something like that) as a means of diagnosis. (If there had been a vibration, we hadn't paid attention to it and he did this at no charge, all on his own) Also, a few years ago, prior to our move, the transmission was rebuilt twice (once under the transmission shop's warranty) and I don't remember what the vehicle was doing, but on a third trip the transmission shop had to do something with the transfer case.
Mostly around 40 MPH -- though it may just be too subtle to notice at higher speeds and we rarely drive this vehicle on the highway, so we're mostly traveling short distances at 35 & 45 MPH -- the SUV lurches a bit toward the left and there's a little jerk in the steering wheel. It really feels like I described, like it's getting caught in a rut. Both the car and the steering wheel jerks to the left side. There hasn't been any noticeable uneven wear over the three months we've been trying to figure this out and the front tires look straight up and down. We also haven't noticed any noise. Not going down the road, not when we turn or when the steering wheel jerks.
View 14 Replies
2005 Mazda Trib. will not let me shift out of park . It doesn't happen all the time button seems to be sticking . Is it the button or the electrical switch on the brake pedal ? This belongs to a friend of mine and this is the info I'm getting .
View 2 Replies
I was leaving work in my 05 Escape. Started up fine, made it to the other end of the parking lot and it died. Restarted it and made it about 10 feet and it died again. Now when I try to start it, it just make a single click. Tried getting a jump from a friend and nothing but the same click when trying to start it. Lights are bright (haven't checked batt voltage yet, but will tomorrow).
View 6 Replies
I have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 Replies