Ford Escape / Hybrid :: 2004 XLT V6 - Power Loss / Vehicle Won't Go Over 30 MPH
Mar 22, 2015
I have a 2004 Ford Escape XLT V6 and I am experiencing a major loss of power in the vehicle. It idles smooth at about 1000rpm's but when you drive it , the vehicle won't go over 30mph and has a significant miss to it. I replaced the fuel filter, put in some Seafoam and took it for a drive and it still did not have any power and I blew out the EGR valve on the test drive. I replaced the EGR valve and the problem still remains. I hooked up a handheld computer to it and I got a P0300, P0304, P0305, P0306, P0316 and a P0355 error codes.
View 1 Replies
Advertisement
My escape struggles to reach 30 mph.. throttle position sensor code when scanned.Replaced the sensor but still barely any power check engine light hasnt come back on.
View 9 Replies
So heres the story..........'02 Escape, 179K miles, just had the oil changed 2 weeks ago, ever since then I've smelled oil burning when the car starts up and every now and then after exiting the car. Also have had the check engine light on intermittently for the EGR insufficient flow for the past few months. It comes and goes whenever it wants. Today Wifey called me and said something was wrong with the car, I drove it home (about 26 miles). The car runs fine as shifts through the gears, but as soon as it gets a load put on it, it cant pull hard like it used to and it gets a high pitched/squealy whistle similar to a turbo that's spooled up.
Its hard to say where its coming from but from what I can tell I'd say somewhere under the hood near the glove box. (that's the only way I can think of to describe it). There's a big long hill right outside her work that I wasn't sure I was gonna make it up. Car just didn't have any power and couldn't decide what gear to be in as RPMs were too high in a lower gear but wouldn't pull in the higher gear. Car pulls hard off the bottom but falls flat in the midrange. I was thinking maybe clogged cat but what would the whistling sound be?
View 14 Replies
So my wife's 2005 escape has been slowly losing power over the past 6 months or so. I regularly change the oil, tried new spark plugs, new air filter and still it's lazy. I know it's not a race machine but it struggles on hills.
This winter it was having problems starting unless the accelerator was pushed to the floor. After a cleaning of the Idle control valve all was well again. It has roughly 72,000 miles on it and uses .5-1qt of oil between changes.
View 2 Replies
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
View 11 Replies
Why do I get an electrical shock when I touch my 2005 Escape? It's not like I drag my feet on a carpet prior to touching it. I had same issue on an other vehicle. It is very annoying - what should I do?
View 7 Replies
A couple weeks ago I had to have both lower ball joints replaced on my '01 XLS 4WD with the 6 cylinder engine. The garage's alignment machine was on the blink, so the mechanic told me to it woudl be fine to drive, and to bring it back this week when the machine was fixed.
The Escape seemed to drive fine until today, coming home from work, the Escape veered slightly to the right, and there was a brief sensation in the steering wheel as if it had been disconnected, as if something slipped. Then the steering was back, and although I was tracking straight down the highway, I noticed the steering wheel was turned to the left. It seemed to steer fine, although I had slowed way down.
View 4 Replies
I have an 05 escape xls 4cyl that has started acting up in the past 2 weeks. The vehicle has 52k on the clock and has no other issues but what im posting about.
Heres the problem: Vehicle starts fine every time you turn the key. It does not stall or idle rough when engaging the trans mission so I've concluded it has nothing to do with the torque converter. Once the car is running the vehicle will shut off randomly with the THEFT light coming on. I played with it for about 2 hours and have found that it will do this idling in Park, while in Reverse, and while in drive. The vehicle also will shut off while I am going down the road and every time it does the THEFT light is coming on as the problem starts. It does appear that it only happens when the accelerator is not depressed and will sometimes stay running if you hit the Gas Pedal as soon as it starts to happen.
I have tried using another key figuring maybe a transponder is bad...No dice does the exact same thing. I have also noted that i do hear single quiet (tock) when the vehicle shuts off coming from the drivers side lower engine compartment.
View 10 Replies
I am running into some issues with my 2011 Escape 2.5L. I am pulling a total of 7 codes. Two codes keep repeating, which those are P0455 and P0457. And I am also getting a C1963. Accompanying the engine codes, my HUD is displaying "Check Fuel Inlet" when I first turn the vehicle on.
View 10 Replies
'04 Nissan Pathfinder 3.5L ~150k: P0011 and P0021
Friend's vehicle. OBD-II codes indicate Intake Valve Timing Control Bank1 and Bank2. Vehicle drives OK most of the time, but then has lapses of lost power where you step on the gas and the vehicle doesn't accelerate accordingly. RPMs rise, but tranny doesn't seem to shift at the right time. Overdrive button OFF doesn't seem to have any affect. Codes have been erased and returned the next day.
Is this Camshaft-related, as in Camshaft Position sensor? I had this issue with my '97 Taurus, but in that case it threw the code explicitly for the CMP sensor.
View 1 Replies
During a highway trip three months ago, my 2004 Prius suddenly lost engine power, the red triangle Master Warning light came on accompanied by a warning sound, and then the Hybrid System Warning sign appeared on the Multifunction Display. I pulled off to the side of the road and stopped. I turned the car off and then tried turning it on again. Engine power was restored although the warning lights remained. We took a chance and carried on with our trip. The same sequence of events reoccurred about 10 times on our 1,300 km journey. I took the car to a Toyota dealer where they found a C2318 DTC. They checked the battery and the HEV fuse but could not locate the problem.
We returned home and on the way the same thing happened a few more times. My service manual noted that the description for C2318 is Low Voltage Error (Power Supply Malfunction) and the trouble areas are HEV fuse, IGCT relay, Wire harness or connector, or Auxiliary battery. Since the car was nearly 7 years old I thought I had nothing to lose by replacing the battery, which I did. However, on a short 150 km trip last week the problem appeared again, once while approaching our destination and once when we were almost home. There seems to be a pattern in that the problem appears every 150 km or so of highway driving. It has never done it while driving in the city.
View 19 Replies
ACCessory power (Key On) 12v can take anywhere from 2 minutes to 10 minutes after the engine is on. Haven't tried leaving key on engine off for that long, but I would assume it would eventually give power to ACC too.
There is the greenishyellow and black wire to the sound system which is supposed to be key on 12v, and the lower power port (cig lighter type) only gets power after key on.
Its been doing this for years...and I swear it happened after one night of leaving the lights on. Battery has been replaced since, but ever since that once time.
It does always come on, eventually. Doesn't matter if warm or not. If you turn off key, it takes random 2 to 10 minutes to get power back to ACC.
View 5 Replies
Our escape recently started loosing its power steering, once the engine is shut off the power steering is ok. Also some times you can feel a pulsing in the steering wheel. I've been doing some googling and it looks like the dealers are replacing the steering columns to fix the problem.
My question : is this the only fix or if something like some contacts being cleaned or maybe replacing a steering sensor of some kind is the fix.
View 5 Replies
2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
View 2 Replies
Lights come on when the ignition is on, regardless of the position of the headlight switch. They shut off about 1 minute after the engine is shut off. The warning chime dings the entire time until the lights shut off.
I want the light to work with the switch and not come on all the time.
It is not just the daytime running lamps. High beams also work with the headlight switch in the off position, ignition on.
Ignition off, the headlights switch functions as it should.
I bought the Escape about 1 month ago. Dealer purchase so I don't know how to get a hold of the previous owner.
It only has 51,000 miles, very clean and all service records.
View 8 Replies
I had to replace all brakes because the bleeders were rusted in, wouldn't come out. So I bled and re-bled, but the brake pedal is still squashy and goes down too far if I have to stop from any speed. I even used my vacuum pump for evacuating air conditioning systems, pulled quarts of fluid through all the brakes-definitely no 2004 vintage fluid in there any more! Yes, I made sure to never pull the master cylinder reservoir empty, which would let in air. I always start from right aft and end up at left front, in order of bleed first. No leaks, the fluid level is always where I left it on previous session. I must be missing something...How can there still be air?
View 14 Replies
Wife come home the other day after leaving for work with the truck no going past 20KM to 30KM.. After some investigating it seems to be in Limp - In Mode. There was a Check-Engine light & after further investigation found a Vac hose with a leak, repaired this & test drove. Same issue.... then there was a loud hissing sound from the engine area so I investigate & now found the EGR sensor (DPEF pressure sensor ) had blow a hose & fried the sensor.
New sensor was replace along with 2-hoses cleared the engine light but the truck still will not go more then 20KM or 30KM max.. I checked the EGR valve with vac pump & engine stalls or so the valve is good. I have left the neg cable off the batt to try & clear the Limp-In mode without success. Looking for a way to clear the limp-in mode or do I need to clear it with a scan tool?
View 7 Replies
I noticed the lights were staying on after the switch is turned off and engine off. I thought the lights might just stay on for a few minutes, they were still on an hour later and now I can't unlock the doors with either the key fob or the key. Not sure what to do next.
View 4 Replies
My son's escape has been parked for about 6 mos... alternator went out and I refused to pay to fix it due to some disciplinary issues with him. Anyhow, yesterday I went out to go look at it and the hood won't open. When I parked it I took out the battery and shut the hood. Never had an issue opening the hood prior.
When I pull the lever, its real tight - like the cable is not really moving or if it is, it cant be much. I'm afraid it might break if I keep pulling. I tried having him pull it while I pushed and pulled on the hood, still stuck. I have no clue why or how it is stuck, but wondering on any way to get it open. I can't really see in there...through the grill or under the hood.
View 3 Replies
Getting a fuel smell especially when 2004 3.0 escape is idling. Is there a replaceable evap filter or maybe the pcv valve?
View 3 Replies
I have a 2004 Ford Escape 3.0 V6 FWD, and the air conditioning has been blowing only to defrost for a few weeks now. After many searches online, most sources seem to agree it is a vacuum leak, as the selector switch is vacuum driven if you want anything except defrost. I popped the hood and within one minute I found one open vacuum line that looks like it has been worn in two.
The line in question goes from the vacuum canister towards the passenger side of the firewall, then goes to a T connector, then a line (the one that is broken) continues towards the heater core lines to where the break in the line is. I found a picture online of what it should look like, but I am having trouble accessing the line that goes through the firewall and behind the glove compartment. I am pretty sure this vacuum line continues through the firewall between the two heater lines, but after that I am stumped.
I popped the glove box down out of the way and I see two thin vacuum lines and a small metal "can" nearby. The black line goes from a fitting and into the A/C bundle, and the white line goes from the top of the metal canister and down into the same bundle. My main question is which line controls the AC selector, and how do I pass a replacement line through that part of the firewall to make a good connection, as it seems the break is at the firewall itself with no extra sticking out for me to connect to.
View 3 Replies
