Ford Escape / Hybrid :: 2004 Vehicle Starts Right Up Dies / Stalls - Smoke From Rear Of Engine
May 21, 2016
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
View 11 Replies
Advertisement
I have a 2003 ford escape V6 and i have notice when i start it' after setting overnight i notice some blue smoke for a little while then it's stop What could be causing this.
View 1 Replies
I have a 2004 Ford Escape XLT V6 and I am experiencing a major loss of power in the vehicle. It idles smooth at about 1000rpm's but when you drive it , the vehicle won't go over 30mph and has a significant miss to it. I replaced the fuel filter, put in some Seafoam and took it for a drive and it still did not have any power and I blew out the EGR valve on the test drive. I replaced the EGR valve and the problem still remains. I hooked up a handheld computer to it and I got a P0300, P0304, P0305, P0306, P0316 and a P0355 error codes.
View 1 Replies
2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
View 2 Replies
2010 Escape with 74,000 miles. Backstory: This is my daughters car who is away at college about 300 miles away. About a year ago the engine started hesitating when driving and would stall to idle at highway speeds. She took the car in to dealer and they replaced the Throttle body under the CSP that had been issued just prior to the dealer visit. All was fine for about 3 months, then she reports that the car is doing the same thing. Check engine light briefly illuminates and goes right back off when this occurs. She is able to slip the car into neutral and it seems to correct the malfunction. Unfortunately she has gotten so good at this that she keeps her hand on the gearshift when driving. It seems to happen at various speeds with no warning and no lasting effects.
She came to visit for Christmas and I was able to replicate the problem after about 30 minutes of city driving, but not quick enough to take a picture of the wrench that illuminated briefly. I slowed to the edge of the road, put it in park and turned off the key (engine ran the whole time at idle). Cranked back up and good to go! She had the oil changed about a thousand miles ago, I replaced the air filter last night and she had to return to her house for work in the next couple of days. She said it happened 5 times on the way home last night.
Car has always been serviced regularly and was a certified pre-owned when we bought it in March or so of 2012. I also bought the extended warranty although that may be expired by now.
Her local dealer said they can't fix it if the CEL is not on or the problem is not occurring at the exact time they have it in the shop. Now, I am not sure but was under the impression that the computer would record any codes and store them even if the light went off and the car returned to normal.
View 6 Replies
'97 dodge dakota engine starts and vehicle will move and then engine dies. Just bought it and it ran fine. Coil was replaced by previous owner four months ago. At times it will run fine but is not reliable and wife will not drive in it. Had it towed to dodge dealer and they said it needed a new coil which they installed and still have the same problem and now think it might be the ecm which is mine even if it does not cure problem. Truck has 145k miles and otherwise is in good shape. When it does run, engine is strong, automatic shifts good and all accessories work. But, it won't keep running.
View 14 Replies
I just bought a 2010 3.0 V6. Oil is leaking down the engine on the rear passenger side of the engine. It starts near the top. I replaced the rear valve cover gasket but it still leaks. I am concluding that it must be the timing chain cover. I can't find any info on how to diagnose and how to repair.
View 8 Replies
My 08 escape (3.0) wouldn't go over 45-50mph Sunday on my way home. The next morning I made it about 2 blocks and the battery light came on and it died. I am replacing the battery tomorrow because it tested bad but believe there is also an exhaust problem. Last week it began making a noise I could hear inside the car only when accelerating. Almost sounded like a small,air plane. The car will start and run now but cuts out and sometimes will Rev up when I press accelerator and sometimes won't. The exhaust pipe gets hot really fast and it and the motor both vibrate we the car is started (more than normal) any clue on where to start??
View 1 Replies
2002 3.0L escape 4WD, stalled twice on me when shifting into reverse after a complete stop. No CEL, truck started right up again....
View 4 Replies
Why do I get an electrical shock when I touch my 2005 Escape? It's not like I drag my feet on a carpet prior to touching it. I had same issue on an other vehicle. It is very annoying - what should I do?
View 7 Replies
Couple weeks ago, was in a spot that needed 4wd. Turned the switch, the 4x4 dash light came on, but rear wheels didn't do anything. Lucky that we were able to get out with ft wheels only. Has 3.0, xlt version.
View 13 Replies
The car has 130K on the clock, and I don't know if she's had the plugs replaced, but the car has been stalling on her suddenly once it warms up, like the ignition switch is switched off. Then, once it cools down for a night, it runs again. If it only cools down for an hour or two, it will run but only for a few miles before quitting again. I'm thinking a sensor, pcm, or coils, but I'm hoping there's some way to narrow this down a little bit.
View 10 Replies
My 2003 escape stalls from park to reverse and drive,not all the time but when warmed up. IAC motor replaced and still stalls.
View 7 Replies
I have an 05 escape xls 4cyl that has started acting up in the past 2 weeks. The vehicle has 52k on the clock and has no other issues but what im posting about.
Heres the problem: Vehicle starts fine every time you turn the key. It does not stall or idle rough when engaging the trans mission so I've concluded it has nothing to do with the torque converter. Once the car is running the vehicle will shut off randomly with the THEFT light coming on. I played with it for about 2 hours and have found that it will do this idling in Park, while in Reverse, and while in drive. The vehicle also will shut off while I am going down the road and every time it does the THEFT light is coming on as the problem starts. It does appear that it only happens when the accelerator is not depressed and will sometimes stay running if you hit the Gas Pedal as soon as it starts to happen.
I have tried using another key figuring maybe a transponder is bad...No dice does the exact same thing. I have also noted that i do hear single quiet (tock) when the vehicle shuts off coming from the drivers side lower engine compartment.
View 10 Replies
I have a 2008 xlt with a 3.0. In the little over 2 years I've had it, most notably in the past year, I have replaced the front driver side ABS sensor 8 times. This is getting extremely cost, and outrageous. Every month or so, the ABS light comes on and the ABS starts locking up when I am driving it. Every time it does it, I have to take it back to the shop for diagnostics, at a rate of nearly 300 a pop. As you can see, the bill for this one damn sensor has become outrageous.
Every time, the same fault code comes up. Drivers front ABS sensor. Putting on a new sensor fixes it, every time, but only temporarily. I have had the tone ring replaced just to make sure that wasn't it, and every single time it's always been the sensor itself.
I have tried various brands, including a couple of OEM a pop to make sure it wasn't just lower quality parts, and I have the exact same result every time. I have noticed it seems to do it most notably during extremely wet conditions, or heavy snow, although a couple of the times it started acting up in the heat of summer. I have even attempted cleaning the abs sensor to make sure it wasn't just dirty, to no avail.
As I mentioned, only replacing the sensor makes the issue go away, and when I am driving the abs system engages at random times if I leave the light on for too long without fixing the abs light.
View 8 Replies
Vehicle: 2001 Escape 3.0L V6
I'm listing here the obvious that has been changed already:
1) Valve cover gaskets
2) Oil pan gasket
3) Timing chain cover gasket
4) Upper and lower manifold gaskets (not oil related but changed)
5) PCV valve
6) Washed engine twice to remove everything and make sure nothing else burning
Problem: I still have a small leak from the top that causes smoke near or around the #4 COP on passenger (left side of the motor). But we do see some oil coming from near the PCV valve. It makes no sense and after reading what caused smoke on that side of the vehicle I changed the Timing chain cover gasket (which were finished anyway) and while was at it the oil pan but to no avail. Smoke and leak still there.
Probably not: I know that it is not the head gasket because there is no sign at all; I've never lost a drop of coolant and there is no smoke from the exhaust in back.
Suspicion: Could it be the oil separator where the PCV valve connects and makes it's way around to the other side? Is there something I am overlooking? There can't be many other places for an oil leak like that.
Coincidence ? : Even after changing all the COPS and spark plugs I found oil in the #4. However smoke was there before. I thought maybe a cylinder gasket I got second opinion from my mechanic says no not cylinder...
Engine runs well except for misfire in #4 but comes and goes. I think when oil builds up.
View 5 Replies
Posted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 Replies
I am running into some issues with my 2011 Escape 2.5L. I am pulling a total of 7 codes. Two codes keep repeating, which those are P0455 and P0457. And I am also getting a C1963. Accompanying the engine codes, my HUD is displaying "Check Fuel Inlet" when I first turn the vehicle on.
View 10 Replies
I've got this 96 neon. I can drive it to work and almost exactly 10 miles into the trip everyday I notice a subtle chug. Then it gets worst and within a couple of miles it chugs progressively worse until it dies. I pull over to the side of the road for 5-10 minutes. Then I can start it back up and run down the road another 3-5 miles before it happens again. I've changed the computer, coil, cam positioning sensor, O2 sensor, gutted the cat, changed plugs and wires. I'm to the end of my rope with this car. The codes that its throwing are no dice.
View 7 Replies
I am working to analyze my Granddaughters 2008 Escape FWD Auto 2.3 L issues with the Transmission. Vehicle has 142K miles with engine oil changes but no maintenance on the Transmission.
Engine was replaced about 9 months ago with a used 2.3 L with 52000 miles. Engine runs fine with no issues and NO Codes. BUT when driving the Escape I find it starts out in 1st gear and with a little feathering of the throttle will shift at 2600-3200 rpm directly to 3rd gear. (Based on known ratios and rpm vs MPH) Also no OD/ 4th gear. OTHER than the shifting issue it runs fine.Reverse works normally.
Summary: NO CODES from OBDII, NO OD lite ON or flashing, NO leaks, "wrench" light is ON solid after 1-2 miles driving, "wrench" light is OFF on restart but turns ON after 1-2 miles driving, Changed ATF - old fluid was slightly dark but looked and smelled OK - Drain plug magnet had slight coating of sludge - no dirt, metal or other solids. Transmission Shifting Lever properly selects Park - Reverse - Neutral - Drive with a quick/Normal change.
View 9 Replies
So, I recently bought a 99.5 Jetta. (99 with a 00 body), fixes a few things. Alternator, oil pan, head gasket. I recently drove the car just up the road, drove it back. Went to pull in to my spot and it shut off! Wouldn't start but would crank over. Days go by, same problem. Runs for about 10 minutes then just dies. Fuel pump works, fuel filter isn't clogged. And the fuel relay works.
View 1 Replies
