I noticed the lights were staying on after the switch is turned off and engine off. I thought the lights might just stay on for a few minutes, they were still on an hour later and now I can't unlock the doors with either the key fob or the key. Not sure what to do next.
View 4 Replies2008 Escape, while driving, the doors will lock/unlock themselves like crazy. Sometimes it's 20 times, others it's 100 times. Sometimes it won't happen for a day or two, sometimes it's every time I drive it. When the car is off, remote works fine, car stays locked. Where to start?
View 2 Replies2003 Explorer Sport, 4X4, keyless entry. Bought the truck brand new but never had occasion to use the keys in the door and tailgate locks. Tried them this week and they did not work the locks. I first thought that the locks were frozen. Not the case. Stopped by the dealer and he suggested spraying WD40 in the locks. Didn't work. Got a new 'blank' cut by the dealer in case the key was worn, didn't work. What might be the issue? I was thinking that the wrong cylinders were put in the truck on the assembly line. I have a key fob remote and keyless entry but it would be nice if the key unlocked the doors in an emergency.
View 6 RepliesPrius sat in my garage for about a month without moving went to start it up had 0 power, the unlock button on the keys wouldn't even open the doors. So I tried to jump start the car which would kind of work. The car would turn on for a few secs maybe 5 sec then turn right back off. So had the battery tested and came back as bad battery.
View 13 RepliesMy wife said that her keys stopped locking/unlocking doors. I checked the keys and replaced the battery just to be sure. No change. Older keys also couldn't unlock/lock the car.
Both keys can start the car and has blinking red LED flushing when any buttons pushed. Is there a "Remote" button somewhere in a car to allow remote operation?
2007 RX400h 110k mi.
Reprogram remote to unlock all the doors with 1 press? I cant stand hitting the remote twice for all the doors..
I reprogrammed my Jeep to do this but I can figure out how the sequence that works for the Truck....
I have a 2004 Screw lariat. When i turn the truck off, the locks no longer unlock automatically. Also when I press the unlock on my key fob, the headlights flash, but the doors do not unlock. And the driver side lock/unlock switch is no longer working either.. could this be a broken wire?
View 8 RepliesI recently purchased a 2006 Ford F-150 XLT and don't know very much about it, nor Fords in general. I was just wondering if there is any way to have the power doors unlock automatically when I shift into Park or turn the ignition off? It has the option to have the doors automatically lock once I reach 5-10 mph, but I can't find any information about programming it to unlock automatically. It doesn't have the programmable computer display, so everything requires pressing a bunch of buttons when the key is turned on accessory and things like that. I have kids who are always in the back seats, and it gets annoying trying to get them out of the truck when it's off and I forget to manually unlock them.
View 6 Replies2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
Lights come on when the ignition is on, regardless of the position of the headlight switch. They shut off about 1 minute after the engine is shut off. The warning chime dings the entire time until the lights shut off.
I want the light to work with the switch and not come on all the time.
It is not just the daytime running lamps. High beams also work with the headlight switch in the off position, ignition on.
Ignition off, the headlights switch functions as it should.
I bought the Escape about 1 month ago. Dealer purchase so I don't know how to get a hold of the previous owner.
It only has 51,000 miles, very clean and all service records.
I had to replace all brakes because the bleeders were rusted in, wouldn't come out. So I bled and re-bled, but the brake pedal is still squashy and goes down too far if I have to stop from any speed. I even used my vacuum pump for evacuating air conditioning systems, pulled quarts of fluid through all the brakes-definitely no 2004 vintage fluid in there any more! Yes, I made sure to never pull the master cylinder reservoir empty, which would let in air. I always start from right aft and end up at left front, in order of bleed first. No leaks, the fluid level is always where I left it on previous session. I must be missing something...How can there still be air?
View 14 RepliesWife come home the other day after leaving for work with the truck no going past 20KM to 30KM.. After some investigating it seems to be in Limp - In Mode. There was a Check-Engine light & after further investigation found a Vac hose with a leak, repaired this & test drove. Same issue.... then there was a loud hissing sound from the engine area so I investigate & now found the EGR sensor (DPEF pressure sensor ) had blow a hose & fried the sensor.
New sensor was replace along with 2-hoses cleared the engine light but the truck still will not go more then 20KM or 30KM max.. I checked the EGR valve with vac pump & engine stalls or so the valve is good. I have left the neg cable off the batt to try & clear the Limp-In mode without success. Looking for a way to clear the limp-in mode or do I need to clear it with a scan tool?
My escape struggles to reach 30 mph.. throttle position sensor code when scanned.Replaced the sensor but still barely any power check engine light hasnt come back on.
View 9 RepliesI have a 2004 Ford Escape XLT V6 and I am experiencing a major loss of power in the vehicle. It idles smooth at about 1000rpm's but when you drive it , the vehicle won't go over 30mph and has a significant miss to it. I replaced the fuel filter, put in some Seafoam and took it for a drive and it still did not have any power and I blew out the EGR valve on the test drive. I replaced the EGR valve and the problem still remains. I hooked up a handheld computer to it and I got a P0300, P0304, P0305, P0306, P0316 and a P0355 error codes.
View 1 RepliesMy son's escape has been parked for about 6 mos... alternator went out and I refused to pay to fix it due to some disciplinary issues with him. Anyhow, yesterday I went out to go look at it and the hood won't open. When I parked it I took out the battery and shut the hood. Never had an issue opening the hood prior.
When I pull the lever, its real tight - like the cable is not really moving or if it is, it cant be much. I'm afraid it might break if I keep pulling. I tried having him pull it while I pushed and pulled on the hood, still stuck. I have no clue why or how it is stuck, but wondering on any way to get it open. I can't really see in there...through the grill or under the hood.
Getting a fuel smell especially when 2004 3.0 escape is idling. Is there a replaceable evap filter or maybe the pcv valve?
View 3 RepliesI have a 2004 Ford Escape 3.0 V6 FWD, and the air conditioning has been blowing only to defrost for a few weeks now. After many searches online, most sources seem to agree it is a vacuum leak, as the selector switch is vacuum driven if you want anything except defrost. I popped the hood and within one minute I found one open vacuum line that looks like it has been worn in two.
The line in question goes from the vacuum canister towards the passenger side of the firewall, then goes to a T connector, then a line (the one that is broken) continues towards the heater core lines to where the break in the line is. I found a picture online of what it should look like, but I am having trouble accessing the line that goes through the firewall and behind the glove compartment. I am pretty sure this vacuum line continues through the firewall between the two heater lines, but after that I am stumped.
I popped the glove box down out of the way and I see two thin vacuum lines and a small metal "can" nearby. The black line goes from a fitting and into the A/C bundle, and the white line goes from the top of the metal canister and down into the same bundle. My main question is which line controls the AC selector, and how do I pass a replacement line through that part of the firewall to make a good connection, as it seems the break is at the firewall itself with no extra sticking out for me to connect to.
What airbag code 36 is and how to fix it?
Its a 2004 3.0L limited .....
P0403 code that came up on our 2004 Escape 3.0.
Weekend before last I dropped the oil pan, cleaned it and the pickup screen out, and replaced the gasket (switching to full synthetic has been a double edged sword with the leaks that are popping up...); put in new plugs new upper intake manifold gasket and cleaned the throttle body and manifold out. All vacuum hoses inline with the EGR solenoid have also been replaced since the light went on.
While driving the following day the check engine light (CEL) came on and when checked at pep boys read P0403 (no other codes for low EGR flow, etc.). Now, the EGR solenoid is the newest non-regular maintenance item under that hood because the same code came up a couple of years ago (a new solenoid from pep boys fixed that lickety split) so I wasn't overly concerned that it had popped up again, but a bit frustrated that the solenoid only lasted as long as it did. Also, since the light popped up, I have replaced a couple of vacuum lines with some generic 4mm ID (5/32", I think) rubber vacuum hose, but that just headed off what looked like some potential future problem leaks.
Now, here I am a couple of weeks later having tried 4.5 new solenoids (Amazon sent me one with the wrong wiring harness clip so I couldn't verify that it was connected when it didn't work), and thrown some other "just in case" parts at it (new EGR valve and flow sensor, but these may be returned, but may just end up keeping them on, we'll see how things work out). I'm getting a solid reading from the hot lead on the solenoid harness at idle and during static revving, but I can't seem to get anything on the ground pin.
I've cleaned the connections and the larger pin block going into the top of the firewall to no avail. Should this read as a fluttering ground signal all the time, is it only grounded exactly when it wants the solenoid to open the EGR? What can I do to confirm that it should read grounded so I can know one way or the other whether there is a break in the line? I can't find my multimeter (or just dreamed that I picked one up last year). I'm also curious as to whether or not there's a good way to bench test the solenoid. I don't really get a reaction when I hook it up to 12v directly like I do with a vacuum solenoid from my Saab where there's an audible "click."
Is the wire harness for the solenoid a known weak spot? I've found two potential donors at the local junk yard that I can cut the wires out of to play around with/solder a new one in if that's something that the consensus deems may solve my cause. I also had an ABS light come on not too long after the CEL, but when I reset the CEL the ABS light went away and never came back (it only came on when I hit a big expansion joint on a highway bridge, no braking issues since it's been reset and ABS seems to be fully functional, per gravel road test). I still can't seem to read any ground signal at the solenoid harness at idle or with throttle input. I'd like to fix it, but don't want to start digging into the wires blind.
My Key FOB is only locking the doors but won't unlock.
View 2 Replies…well, I guess it just had to happen sooner or later! I was out running errands yesterday, and when I returned to my car, found that I was unable to unlock the doors, so I tried the buttons on the SmartKey FOB all to no avail, so ended up using the mechanical key to unlock the door, and placed the FOB in the slot in the dash. I checked the FOB battery when I got home, and found it to be slightly less than the 3.00V, plus the fact that it was quite cold yesterday, so that might have been a contributing factor. I've not needed to replace the FOB batteries in the 2 years I've owned the car.
View 3 Replies