Couple weeks ago, was in a spot that needed 4wd. Turned the switch, the 4x4 dash light came on, but rear wheels didn't do anything. Lucky that we were able to get out with ft wheels only. Has 3.0, xlt version.
View 13 Replies2005 xlt 4x4. I was cleaning the threads on the rear constant velocity joint before taking the nut off. Turning the hub was almost impossible without using a steel bar. Is it supposed to be this difficult to roll the rear axles? Yes the selector is in neutral....
View 2 RepliesMy wife just picked up the 2015 Escape 3 weeks ago. This is now the 3rd time back to the dealership with it where nothig on the dash is working. No information center, no speedometer, no tach, no fuel gauge, no temp gauge, and even the entire media screen is powerless. So in turn, a lot of the temp controls and radio are gone.
The first time was on a weekend, I pulled the fuse that powers the entire dash to check it, it was fine and upon putting it back in, everything worked. Still had it to the dealer and they couldn't find anything wrong with it. The 2nd time was this past weekend, we decided to leave it so the service team could see what we were talking about. They again, reset the fuse (still wasn't blown), tightened a couple connections, but really couldn't find anything wrong with it.
The 3rd time was just this morning and the vehicle is currently with Ford now. Obviously warrantied, but did their dealership find what the issue was? We really love the Escape, when everything works right.
My 2003 Escape 2.0L has the "door ajar" light on the dash permanently lit, including with the engine off and key removed, which means that I have to switch the courtesy light on and off by hand or else it stays on.
Obvious first guess is a fault with a door or tailgate switch, but they all look OK to a visual inspection. Are there any multimeter tests I can do? Any specific voltages, resistances to look for?
I've just replaced a front ABS tone ring on my 2003 Escape and I'm ready to replace the axle nut (I've got a new one, as per Ford's recommendation) and torque up. I've heard that you're supposed to torque the axle nut *before* you put the wheels back on the ground, but I have the factory service manual for the 2003 Escape and I can't find anything to back that up.
I've looked at every listed procedure I can think of that involves removing and replacing the axle nut, and none of them specify that you must torque the nut with the wheels in the air.
It would be easier for me to do it with the wheels on the ground, but would I be risking bearing damage if I did that?
I thought my tranny shift points had gone a little nutty. This afternoon, it suddenly seemed as if it were starting off in 2nd gear...then the OD light started flashing. Now, when you put it in 1st gear manually, or reverse, it's like it's in park. Can't push the truck or anything...put it in drive or 2nd, and it starts off slowly. Once it picks up speed, all seems well. Definitely not starting off in 1st or going into reverse at all. Have y'all seen this problem before?
View 9 RepliesMy 2002 X won't shift into 4wd. The dash light comes on, but only my rear wheels are engaging. Trying for a half hour, I intermittently was able to get it into 4LO without the front wheels engaging still, but it took me a long time to get it out of LO. While in neutral, I would switch the dash selector out of 4LO into 4HI and it wouldn't switch. Id move the truck a few feet forward and then back and try again and finally got it out of 4 LO, but it went back to just the rears, even with the 4x4 HI dash light on. I replaced the ESOF hubs with warn hubs a few months ago, so the ESOF aren't the problem. The only thing I didn't do when I swapped out the ESOF was plug the vacuum lines, would that affect manual hubs? I am visiting relatives in eastern WA and it has snowed 5 inches in the past few hours. I need to make it 180 miles home tomorrow.
View 3 RepliesAfter 5 days on raining my escape will not start... It tries but then sounds like the battery goes dead tried jumping it didn't work. Took the battery to be check and it's good...
View 9 Replies2005 2.3Liter 4wd Mariner, 225k miles
I have been experiencing clunk noise on the front end when braking or accelerating and turning wheels.
I have replaced: front control arms, ball joints, tie rod ends, sway bar bushings and stabilizer links and 2 days ago I replaced strut mounts and bearings.
The steering is smooth after the strut mounts replaced but I can still hear cluck noise mostly on left now when going over bumps, braking and accelerating.
Car also has new engine/trans mounts.
I am so lost right now because I cannot figure out what is it. The only thing I didn't replace are the struts but the I test them and they seem to function fine.
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
I am having a lot of issues with my 2002 ford escape, a while if I drive the truck acts normal, but after driving it starts missing when beginning to accelerate at a dead stop check engine light starts flashing pulled codes coming up with #4 cylinder misfire and #5 cylinder misfire detected, also a catalyst system below threshold bank 2, I have had the vacuum lines repaired and still no changes and went through and changed my grade of fuel from regular unleaded fuel to premium fuel, actually went worse with using premium fuel. I was thinking of replacing all three coil on the front of the motor, putting new plugs in it and seeing what that does.
View 2 RepliesGirlfriends 04 escape airbag light is blinking code 37. Read something about it being on passenger side what do I look for? I just got done putting in 2 coils, 2 cats, egr, o2 sensor, intake gaskets upper and lower, PCV, injector orings all due to misfire sure there not connected just added info. Other problems include heated seat switch lights for a second then shuts off, and no cruise control. Need to get light off for inspection by end of month....
View 2 RepliesOver the past few days the battery light has been flickering and at times staying on. In using the gauge cluster diagnostics, I am getting 12.4 engine off and 13.8 - 14.0 with the engine running.
Even when I'm driving with the battery warning light on I still get a consistent 13.8 - 14.0 (and I do have the headlights on, the A/C running, radio, etc).
Kind of scratching my head on this issue since it appears the alternator and battery are working correctly.
So we bought a new to us 04 Escape for the kid, he loves it! My question is, what's going on when I accelerate somewhat aggressively, the tach and speedo peg high and battery light comes on. It does not affect performance and gauges return to normal within a couple seconds.
View 11 RepliesIs there a heater core bypass valve under the hood that may be suspect or would a heat transfer door under the dash be the culprit? Engine operating temp seems to be fine.
View 14 RepliesCan the speedo and tack lights be dimmed to almost off with the + and - buttons either side of the headlight switch on a 2014 Escape?
View 2 RepliesThis 2002 ford escape 3.0 xlt 4x4. on the dash you have your transmission #s laid out . the #1 seems to always be highlighted in a square. but as you move the shifter to whatever gear you want there is another square that highlights the selected gear. Also, before when you would have it in D it would flash back and forth from D to 2 just the lights not the transmission.
View 1 Repliesok this has me stumped I get this buzzing/humming/vibration sound from what seems like around Defroster passenger side but it is not all the time only at higher speeds and it it intermittent . I have removed cabin filter and cleaned filter box and checked for a leaf or something even sealed somewhat the plastic shield that covers the cabin filter. I really don't want to rip dash apart but it is so annoying
View 14 RepliesStarted up my 6 cylinder 2005 Ford Escape with 187,000 miles on the engine this morning and after 5 minutes a check engine light came on and the car shut off on its own. I restarted the car and then I got a dash message "Service Emissions" and the car shudders a little when driving. I am going to the autoparts store later for a OBD scanner code check.
View 1 RepliesThe connector is near the floor (that's the gas pedal, in the picture). I've slid back the red clip on both, but the connector still will not separate. Is there a trick?
2001 Escape V6....
Get a set of real gauges if you want to do diagnostics. 110 psi on the low side indicates that the system isn't running at the time and that the underhood temp is around 100 F.
View 1 Replies