Ford Escape / Hybrid :: 2003 V6 - No Key On Prime / Zero Line Pressure
Jun 4, 2016
No key on prime. Inertia switch OK. Zero line pressure when filter removed & changed. Tries to start with ether. Front 3 coils are for sure firing. Swapped the pump relay with fan relay, no change, no prime.
I'm working with an 03 factory hard copy manual & I'm just not seeing a testing procedure, but I'm bat blind sometimes. What I'm missing? The patient had run fine all day, stopped for an hour. Got back in, started badly, shook somewhat, died, no start since.
View 13 Replies
Advertisement
I need to replace my pressure line on my 02 Escape 3.0L. Looking for a DIY for doing this same job?
View 1 Replies
Changed front brake pads yesterday. Took calipers apart, used c clamp and old break pad to release pressure from the cylinder. Installed new pads. Brakes felt spongie. Drove truck forward and backwards hitting the brakes. They tightened up some what but still spongie. Drove truck with no change. Decided to bleed front brakes. Now I have NO brake pressure at all.
*rotor on left side did have small groove but was not replaced... would this possibly be contributing to my issue.
View 4 Replies
I'm having an issue with my ford again. Escape, V6, 123k miles. Recent work done: Replaced all spark plugs, coils, and intake manifold gaskets. Replaced all four O2 sensors. Oil change switching from the 5w-20 to 5w-30 due to it getting cold, (probably a month ago?).
Now for my current problem. Two days ago on a 20* morning, after it sat outside all night, I drove about 3 miles and then noticed the oil pressure light was blinking intermittently. When I came to a complete stop, it stayed lit. I pulled into a parking lot and starting shutting stuff down. I noticed when I turned the heater blower off, the light went out. Turning it on to High, I noticed the RPMS on the tach dropped to around the 500 mark, and the oil pressure light came back on. I turned it off and let it sit for about 45 minutes. Oil is showing good on the dipstick. I then drove it the last two days without the light coming on.
Now this morning, driving it again in 20* weather, after it sat outside, the light came on again, in almost the exact same place away from home. Both times the motor had reached operating temp, with the temp gauge being in the middle between "C" and "H". This time, even with turning the blower off, it came on every time it was at idle. I let it sit another 45 minutes, but this time when I drove it, the light was more intermittent and then was constant.
Again, the oil level is good on the dipstick, and the motor seems to be running smooth. I'm wondering if this could have anything to do with changing over to a different oil and with it being so cold in the mornings?
I have it written down at home, but I can't remember when I did the actual oil change, but its probably been a little over a month. I went from 5w-20 Pennzoil, to 5w-30; wix filter. I'm planning on doing another oil change tomorrow when I get home and go back to the original 5w-20. Also, I'm ordering a new oil pressure sensor, and I'll try that also. I've also looked into an oil pressure tester....
View 14 Replies
2008 Escape V6
Got the oil changed at Walmart and they told us there was oil in the air filter and we should replace the pcv valve. Before we changed it the oil pressure light had started coming on when the car is stopped, either in gear or park. Once the gas is hit it goes off, even at something like 1 mph. Well I changed the pcv valve but the oil pressure light is still doing the same thing. What should be my next step?
View 2 Replies
With winter on its way I have installed winter tires and steel rims w/o pressure sensors on my 08 Escape. Is there a way to disable the dash warning light for low tire air pressure?
View 14 Replies
I just put on new winter tires and rims on my 2012 Escape and after driving about 6 miles, the low tire pressure light came on. Is there is a procedure to learn the vehicle to the new tires?
View 6 Replies
My friends 2006 Escape has the ( low pressure warning light) flashing on for about 10 seconds after starting the engine. All tires are at correct pressure. What is causing this?
View 5 Replies
The facts: 2009 4x4 V6 Escape with Valve stem mounted TPMS
I am getting a tire pressure sensor malfunction fault. The warning light is on and the error message is displayed on the little screen in the gauge cluster.
What I have tried: First I should say I have replace to defective sensor twice now...
1) I put the escape in tpms train mode by hitting the hazard switch off/on about 6 times.
2) I used the train tool to train all the tires but there is one that is giving me trouble and will not train.
3) I tried deflating the problem tire and inflating it to the specified pressure given on the be pillar of the escape (30 psig)... after inflating it I tried to retain it with no luck.
4) I tried rotating the tires and as I mentioned earlier I have replaces the problem sensor twice. Still can't can't get the problem tire to train.
My thoughts:
1) I don't think this is a module error because I can train the other tires and since I rotated them I know their position is not a factor.
2) its possible that I have got two defective tpms sensors but I think that is unlikely.
3) I have read of another procedure to put the escape in tpms train mode that requires you to turn the ignition on/off, step on the break pedal, tap your head and rub your belly, etc... but I have not tried this method. Is there a difference from this train mode verse hitting the hazard switch on/off about 6 times?
4) Does the train tool only work on previously trained sensors? do I need to register the new TPMS sensor with the TPMS module? I have an OBDII tool that connects to scanXL software on my laptop which included the ford proprietary protocol. I looked for a way to program a tpms sensor (similar to how I did it with my toyota) but couldn't find the option.
View 4 Replies
Over the weekend my 2008 Escape Hybrid manifest 2 problems the same day.
1. The remote keyless entry button stopped working (thought it was dead battery in key)
2. Got a error message 'Tire Pressure Sensor Fault'
So after suffering with having to actually unlock my car with a key (heehee/see sarcastic grin) and getting irritated by the error message. I asked the internet about my symptoms. Got the standard answers of "bad tire pressure sensor/reprogram" and change the battery in the key. But ONE and only one person (namely Enviroguy ) said what I thought was going on - that these two problems were related. (afterall it is 2 wireless devices in the car.)
Changing the key fob battery had no effect & Both keys were unresponsive. Seeing what Enviroguy said about certain chargers or wireless devices can cause interference in the tire sensor and keyless systems. .... Then I remember that I had been using a new no-name charger for my cell phone when this problem started.
I unplugged that charger.....(it was a cheap generic power point to USB adapter). The Keyless system is working... ! The tire pressure error has vanished.... !
I did not go to the car appointment.... Now let's hope this was in fact the problem! May my 2008 Ford Escape Hybrid "Be Healed!"
View 2 Replies
My ford escape won't let me unlock it my remote start doesn't work but the cars runs fine but today i locked my car before i turned it off which is what i always do. to lock it and when i went to unlock it manually i heard a pop sound and my key won't turn and there's no other way to unlock my car i walked around it 3 times trying to look for a key slot. How to unlock it.???
View 2 Replies
My 2003 ford escape wont shut off with the key off and out of ignition as long as the air conditioning running once I shut the air off the car will shut off. Where to start.
View 2 Replies
Not always & seemingly at random. Just like at startup after battery reconnect.
Most searches come back only with incidents at startup only. Recommendations say battery &/or alternator. Battery is Optima Red that's been in there maybe 6-7 years and all connections are clean & reads 12.48 at rest.
Alt is a AC Delco new unit replaced 20k or so ago & reading 14.24 at idle with or with out any accessory drain on the system or RPM.
Troubling thing is a code for coil misfire on # 5 which put it into limp mode (I erased & so far hasn't returned) & some comm issues with the Inova 1403 that I'm using.
View 6 Replies
I have a 2003 Ford Excursion with the high pressure line leaking. My guess is that the original line had a rubber hose and was replaced with a 3/8" ID high pressure hose. My problem is that I can not get the 3/8" ID replacement hose over the second larger bulge on the line going to the radiator cooler. What am I doing wrong?
View 3 Replies
I have error 19 on airbag warning light. I plan to replace RCM and have it programmed to vehicle. Where is RCM located on 2003 Escape, V6?
View 4 Replies
I'm replacing the ignition lock cylinder on my 03 Escape. The factory cylinder has the little black "wings" that nestle around the key when inserted:
The locksmith says the replacement cylinder needs to have those same wings for him to be change it. Is this correct? The auto part stores have the regular cylinder (with no wings) readily available, but the one with wings is a special-order item and I need this sooner rather than later.
Plus, the wingless one includes keys while the other appears to have none.
View 1 Replies
I have a 2003 Ford Escape Limited V6 replaced thermostat and fuel pump and 3 coils and 3 spark plugs recently. Now the theft light has come on and will not crank or start. The fuel pump is still not working unless I manually press the fuse under the hood which is also the only way the car will crank still will not start. That's because the previous owner got the key stuck in the ignition so he bypassed it with a dial you can turn. The dial will put the car into ACC and on mode but will not get the car to crank. Also btn1 and btn2 fuses under the hood are draining my battery.
View 3 Replies
After 5 days on raining my escape will not start... It tries but then sounds like the battery goes dead tried jumping it didn't work. Took the battery to be check and it's good...
View 9 Replies
My mother-in-law has a 2003 Escape with a V-6. For the last week the rear lift gate and window will not open. Tried the door key and the driver's side door unlocked. Turned the key again within three seconds (according to the operator's manual). The two lights flashed, the remaining doors opened except for the rear gate. I pressed my ear to the gate and it sounds like it is trying to release the locking mechanism. Any recommendations?
View 7 Replies
Just wanted to post a recent experience I had with the catalytic converter issues Escapes seem to be prone to. A friend has a 2003 Escape 4x4 with the 3.0 V-6 and automatic transmission. It has 141,000 miles on it, she bought it with 40,000 miles on the vehicle.
Recently it developed driveability issues: No power with a whistling noise and top speed of 10 M.P.H. I researched on here and her symptoms matched threads that came up using the search function. I told her I was pretty sure the front cat was bad and had plugged the rear cat, causing the issue. She took it to a local repair shop and confirmed my diagnosis. Their estimate for repair was north of $1,500.00. My neighbor and I were sure we could repair it cheaper.
We towed it to my house and pulled the front and rear-most cats. As suspected they were both bad. The back cat on the engine looked pristine inside so we left it alone. We ordered all of our parts from rockauto. New front and rear-most cats, exhaust and intake gaskets, serpentine belt, and one O2 sensor that was damaged when the insides of the front cat let go.
Installation was straight forward with no major issues. We also changed the plugs with brand new ones she had purchased but never had installed. The vehicle now runs fantastic and she is extremely happy with it.
View 14 Replies
2003 Escape Limited V6 Auto 4x4 ... I am having issues with poor fuel milage and starting the SUV...
When i go to start the truck it winds over for abit then starts and revs really high?!?!? I did a complete tuneup, plugs, filter, fuel filter, oil and filter... I changed the fuel pump which has the fuel regulator built into it. I have no codes on the dash. Also if i am at a red light and i put it to the floor I MEAN TO THE FLOOR!!! the truck bogs then drives off NO POWER!!!
Im stumped! I dont know what to do and dont want to keep replacing expensive parts... fuel pump, etc...
View 14 Replies
