Ford Escape / Hybrid :: 2002 - OD Light Started To Come - Got Code P1744?
Sep 7, 2014
2002 Ford Escape... My OD light started to come on every once in a while, and would go off once I turned the car off... This being said, as far as I could tell, the tranny was running smooth. Then an engine light popped on and this code and explanation come up... P1744 "Torque Converter Clutch System Stuck in OFF position".
I recently came back from a bit of a trip... and after shutting the car off, it didn't want to restart. Since this time, the car has begun to start, but the engine light remains on with the P1744 coming up...
Research seems to indicate that the problem is with the Torque Converter Solenoid. You Tube videos show that there are two solenoids just under the transmission pan...
View 7 Replies
Advertisement
After multiple problems with this vehicle already, it's about time that I made an account.
We have a 2003 Escape XLT with around 150k on it, and are now having transmission issues.
It's slipped some when cold and starting from a full stop and sometimes rolling stop, when trying to accelerate. Basically, it acts like it's in neutral until the gears "catch up". Once it's warmed up, it's fine even on steep hills. Also, going in reverse seems to act normally oddly enough.
We were hoping to get through winter as it was since it was easily manageable, but yesterday the O/D light started flashing and we have the pending error P1744. Nothing happened when the error came on including the normal slip since everything was warm at the time.
We'd of course, love to avoid completely replacing the tranny, but I'm mostly learning as I go with this one. Where to start narrowing out possibilities? The fluid was changed when we first got the escape about four years ago and is still at the right level and clear/red.
View 5 Replies
I'm getting a p0452 fault on my 2002 Escape 3.0 V6 2WD. From what I've read, that seems to indicate low FTP signal below .22v. As I understand it, the FTP sensor has 5 v applied, and the output to the ECU goes down as tank static pressure increases. Conversely, I think the voltage back to the ECU goes up as tank static pressure decreases (for the vacuum leak test measurement).
What the approximate voltage is at atmosphere (engine not running, vent valve open, etc)?
I'm guessing the "less than .22v minimum" signal back to the ECU might look more like either the signal wire shorted to the frame somewhere or the signal wire open (maybe corrosion in the connector)....
Also, where the FTP sensor is located on the Escape and how to access it?
View 3 Replies
I have been getting a CEL P0420 for low cat efficiency bank 1 on my 2002 Ford Escape V6. The truck runs fine otherwise. I have ran two loads of Cataclean and the light keeps coming back a few days after CEL reset so I am pretty sure one of cats is done. I am going to replace with an aftermarket cat. My question is, with this code, do I need to replace the front exhaust manifold cat or the rear manifold cat?
View 1 Replies
I have a very Big problem with my Ford Escape 2002 I have this problems code: P0305 accuses Cylinder #5 P0306 accuses Cylinder #6.
I already change the gasket i buy the felpro Kit, and i Also replace all the sparks and spark plug boots, I clean the air sensors and i also replace the EGR, i try to switch cables, and all is the same the car start buy when i accelerate it just go off, i don't know what can i do next, somebody told me to change the fuel injector, i take the pressure in both spark holes the number 4 was 150 and the 5 and 6 was 120, No leaks oil. My car is a Ford Escape 2002, XLT 3.0 4x4
View 2 Replies
I have a Mazda Tribute 2006 2.3. The O/D light would come on, drove it to a friends to scan the check engine light code, and the car almost made it there and then wouldn't remove in reverse, forward, or anything. Turn it off then start it up still wouldn't, then turned it off let it cool and it worked again for a little while.
The code was P0741, just the one code. Took it to a shop to have further tests, they seemed to think it was the clutch was worn and when the fluid heated it lost friction.
Pulled the transmission and thought why not do a Transmission rebuild? I have never done one but there was an awesome video on youtube of the guy doing it so I figured it couldn't be too hard and was just going to try my first rebuild.
According to the guy in the video you always need all new bushing, and we will get a rebuild kit with new clutch packs and the other stuff that comes with those, and sounds like it's a good idea to replace the torque converter.
The car is only at 85K and it looks like the transmission was rebuilt once before he got it at 80K. Maybe a bad rebuild?
Here are some pictures .....
The Input Sprag bearing was shredded and the bushing looks terrible. Can I just replace the bearing and the bushing? Is there any other damage I should be looking for because of this?
The forward planet you can so some eaten metal on the edge and 2 gears spin super smooth and the other 2 you have to push pretty hard to get them to turn. So new forward planet?
The shell's corners look a little rounded I wasn't sure how much was to much, can you tell from the picture if it looks like too much?
Input Sprag
Forward Planet
Sun Gear Shell
View 2 Replies
I have a 2002 Escape XLT V6 4X4. I searched the issue, but others' symptoms don't seem to be quite the same as what I'm seeing. Over the last few weeks, the battery light has randomly come on and off 3 separate times:
- 1st time, light came on at highway speed for about 30 sec and went out. Didn't come back on. Was during daytime, running DRL's, radio (no amp or subs or anything like that, and heater blower on low speed.
- 2nd time was two weeks later or so. Happened at night with just headlights on at around 55mph (RPMs about 2K or so). Again, stayed on for about 30 sec and went out.
- 3rd time was about a week/week and a half later, yesterday morning. Just running DRL's and radio. Light came on, flickered, came on, and then stayed on for a couple of minutes (all at highway speed). I noticed that if I disengaged the overdrive and got the RPMs up, the light would go out. I ran it out of overdrive for about 2 minutes like that, and the light stayed out. Speed limit dropped to 40mph, and the light came back on (lower RPMs at that speed, didn't run it in low gears). Light stayed on for 30 sec - 1 minute, and then went out on its own and has since stayed off.
I took it to Advance yesterday to have it tested, and the results were that it is charging at 13.9V under no load, and 13.87V under a load. The battery tested good, but the machine said it needed to be charged (it hasn't been acting low...car starts just fine).
I'm driving it to work today to see what it does next, and then getting it tested again on my way home. Has anyone here ever had similar symptoms as above? Does this sound like bad diodes in the alternator?
View 5 Replies
Well, I bought a used 2003 Escape for my daughter and without thoroughly researching the airbag light, now have a problem. The light flashes twice, pause, then once, so I think this is error code 21? I cannot find anything on what this code is and how to fix it. I disconnected battery for an hour and now I get 4 flashes, pause, 6 flashes, 46 error.
View 1 Replies
Girlfriends 04 escape airbag light is blinking code 37. Read something about it being on passenger side what do I look for? I just got done putting in 2 coils, 2 cats, egr, o2 sensor, intake gaskets upper and lower, PCV, injector orings all due to misfire sure there not connected just added info. Other problems include heated seat switch lights for a second then shuts off, and no cruise control. Need to get light off for inspection by end of month....
View 2 Replies
We bought a new 2002 Escape 4WD and it has been great. Just clicked 130k. However, yesterday my wife said the car clunked when putting in reverse, and then the OD light started blinking. Shortly after that the Escape would not drive in gear, just a spinning noise. After the car was shut off for a few, it would drive again, but not very far. Fluid is good, and it will only drive for a while. I noticed a broken vacuum line coming from the trans, but could't tell where it went.
View 3 Replies
I picked up a 2001 Escape 2.0 manual with 160K. She runs great but I realized that the airbag light was burned out so I hooked up my scanner and pulled 2 codes C1414 and B1869. I changed the bulb and cleared the B1869 but the C1414 remains. the airbag light also flashes and gives me a 29 code. I am not finding much on the subject. The airbags appear to be there and it does not appear that it has been wrecked. I am guessing that it is the airbag control module. Where the module is located on this vehicle.
View 7 Replies
I thought my tranny shift points had gone a little nutty. This afternoon, it suddenly seemed as if it were starting off in 2nd gear...then the OD light started flashing. Now, when you put it in 1st gear manually, or reverse, it's like it's in park. Can't push the truck or anything...put it in drive or 2nd, and it starts off slowly. Once it picks up speed, all seems well. Definitely not starting off in 1st or going into reverse at all. Have y'all seen this problem before?
View 9 Replies
Check engine light came on and stopped by the local autoparts store to get the error code.
Code: P2270
Bank1 Sensor2 fault
Where is this O2 sensor? I've replaced O2's on other cars I've had and just want to make sure I replace the right one.
View 5 Replies
I got this code and symptoms of 1-2 hard shift and no torque converter lockup. No flashing overdrive light on shifter. If I switch off engine all shifts are smooth until I pass 45mph. I would feel the TCC lockup. This doesn't happen the as i come to a stop I get a harsh 2-1 shift. Key off restart then shifts smoothly up and down provided I dont exceed the TCC lockup speed. This leads me to the TCC solenoid I think. Fluid has been changed regularly.
Had to drive 300 miles to get home. Only for the plate trans cooler the fluid would have overheated as on inclines on cruise control the engine would rev to 3k to keep the speed at 70mph and I could see the fluid temp increasing. Fuel consumption was very bad almost a full tank (with no ac). Doing some research there is talk about valve gasket blowout Epc solenoids etc, though these were for Rangers and Explorers, no real mention of Aerostar.
View 14 Replies
I have a 2001 Ford Escape. When started cold, it revs up to abt 3000 rpm. Slowly drops back to about 1000 in abt 10 secs. When the engine is hot, it often wants to idle 2500+ rpms and I have to really step on the brakes to slow the vehicle. When I disconnect the IAC the engine dies. When it is revving high, I can disconnect and reconnect the IAC quickly, and the idle will drop back down for a few minutes, until I step on the accelerator, then start climbing again. It seems to be a lot worse when hot.
I replaced the IAC and TPS about 20k miles ago and thought it was fixed, but the problem has returned. At that time, I could tap on the IAC and it would "get well" for a while. Tapping on this one doesn't seem to change anything. No CEL, engine runs smooth, and I don't notice any air leaks (none that I've found, at least).
View 8 Replies
When started very high idle after hitting gas pedal sometimes it will lower idle sometimes not,,then holding pressure on gas pedal it has very bad surging ... Any guesses what might be and possible cost fix?? I am no mechanic,will have to take it somewhere...90,000 miles on it..
View 3 Replies
2002 3.0L escape 4WD, stalled twice on me when shifting into reverse after a complete stop. No CEL, truck started right up again....
View 4 Replies
Where can I find the key pad code on an 08 escape? I don't have the card in the glove box and I don't want to pay the dealer. It should be printed on the security module box. Where to find it? On my f250 it was under the dash behind radio.
View 14 Replies
What airbag code 36 is and how to fix it?
Its a 2004 3.0L limited .....
View 1 Replies
P0403 code that came up on our 2004 Escape 3.0.
Weekend before last I dropped the oil pan, cleaned it and the pickup screen out, and replaced the gasket (switching to full synthetic has been a double edged sword with the leaks that are popping up...); put in new plugs new upper intake manifold gasket and cleaned the throttle body and manifold out. All vacuum hoses inline with the EGR solenoid have also been replaced since the light went on.
While driving the following day the check engine light (CEL) came on and when checked at pep boys read P0403 (no other codes for low EGR flow, etc.). Now, the EGR solenoid is the newest non-regular maintenance item under that hood because the same code came up a couple of years ago (a new solenoid from pep boys fixed that lickety split) so I wasn't overly concerned that it had popped up again, but a bit frustrated that the solenoid only lasted as long as it did. Also, since the light popped up, I have replaced a couple of vacuum lines with some generic 4mm ID (5/32", I think) rubber vacuum hose, but that just headed off what looked like some potential future problem leaks.
Now, here I am a couple of weeks later having tried 4.5 new solenoids (Amazon sent me one with the wrong wiring harness clip so I couldn't verify that it was connected when it didn't work), and thrown some other "just in case" parts at it (new EGR valve and flow sensor, but these may be returned, but may just end up keeping them on, we'll see how things work out). I'm getting a solid reading from the hot lead on the solenoid harness at idle and during static revving, but I can't seem to get anything on the ground pin.
I've cleaned the connections and the larger pin block going into the top of the firewall to no avail. Should this read as a fluttering ground signal all the time, is it only grounded exactly when it wants the solenoid to open the EGR? What can I do to confirm that it should read grounded so I can know one way or the other whether there is a break in the line? I can't find my multimeter (or just dreamed that I picked one up last year). I'm also curious as to whether or not there's a good way to bench test the solenoid. I don't really get a reaction when I hook it up to 12v directly like I do with a vacuum solenoid from my Saab where there's an audible "click."
Is the wire harness for the solenoid a known weak spot? I've found two potential donors at the local junk yard that I can cut the wires out of to play around with/solder a new one in if that's something that the consensus deems may solve my cause. I also had an ABS light come on not too long after the CEL, but when I reset the CEL the ABS light went away and never came back (it only came on when I hit a big expansion joint on a highway bridge, no braking issues since it's been reset and ABS seems to be fully functional, per gravel road test). I still can't seem to read any ground signal at the solenoid harness at idle or with throttle input. I'd like to fix it, but don't want to start digging into the wires blind.
View 7 Replies
I have a failure on the evap system of my 2002 Escape, and need the proper testing procedure for this particular purge valve. I was able to fix the purge valve on my 2013 Explorer, with no issue, but the Escape has a different type and I'm not sure I'm testing it properly. I want to verify the purge valve is working properly instead of just throwing parts into it. I know it is likely either the valve or the gas cap, but it could be something other than those two items, so I want to get the simple stuff checked out first.
View 3 Replies
