Ford Escape / Hybrid :: 2001 Won't Idle After Starting - Cold Engine Misfire
Aug 30, 2014
I'm needing cold engine misfire. 2001 escape 3.0 engine 190300 miles on it. I changed the plugs, cleaned the fuel injectors, new air filter, new fuel filter, cleaned the pcv valve and new ideal control valve. When the engine is cold it starts right up but wont idle right and misfires sputters some to but run the rpm's up and it smooths out. drop to idle and it misses. Now when the engine gets to operating temp it seems to run fine. What am I overlooking to find the problem?
View 5 Replies
Advertisement
I have a 2001 Escape, V6 engine and I guess it really does not like it when it's cold outside. Usually the car runs just perfect but when the winter arrives and temps drop into the 20s the truck does not want to run idle right when I first start it. I have tried by stating it without touching the gas pedal. And also by pushing it all the way down and then releasing it. I don't know which method is the right one, but it doesn't seem to make a difference. It takes some time and eventually after about 5 miles of driving it will act normal again. What could I do to fix that?
View 9 Replies
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
View 11 Replies
I have a 2001 Ford Escape, and since the colder weather set in it is tacking below 1 and 'jumping' when idle. When accelerating and/or once the heat gauge has reach midway, the car is fine. I added a bottle of gas additive to the tank 3 weeks back, but the problem persists. The engine light is on but no code is registering.
View 2 Replies
I have a 2001 Ford Escape. When started cold, it revs up to abt 3000 rpm. Slowly drops back to about 1000 in abt 10 secs. When the engine is hot, it often wants to idle 2500+ rpms and I have to really step on the brakes to slow the vehicle. When I disconnect the IAC the engine dies. When it is revving high, I can disconnect and reconnect the IAC quickly, and the idle will drop back down for a few minutes, until I step on the accelerator, then start climbing again. It seems to be a lot worse when hot.
I replaced the IAC and TPS about 20k miles ago and thought it was fixed, but the problem has returned. At that time, I could tap on the IAC and it would "get well" for a while. Tapping on this one doesn't seem to change anything. No CEL, engine runs smooth, and I don't notice any air leaks (none that I've found, at least).
View 8 Replies
I've got an 01 Ford Escape 4 cyl 5spd awd, it idled low when its warm, revs between shifts and if you put it in nuetral and let the clutch out when you're moving it revs to 3500rpms and just sits there until you stop or push the clutch back in. I've replaced the iacv and the pcv valve, elbow and hose, and the tps. What to look at next?
View 4 Replies
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
View 14 Replies
I've read quite a bit in various threads about the large vacuum elbow collapsing, causing erratic idle speeds. My 2001 3.0 had that issue int he past. I shoved a 1/2" copper 45 degree elbow inside of the rubber elbow, and the problem was solved... until a few days ago.
We're now getting into the hot part of summer here. I've notice the same symptoms are beginning to return, once the engine compartment gets hot. My question is... is the large vacuum line a "hard line" all the rest of the way to the engine, or are there other places along it's length that can also collapse under vacuum?
View 3 Replies
I have several problems with my 06 FEH maybe some of you had same issues. I have imported this car from new york in my country 1 month ago, this is first Ford for me. Love this car but there is some issues and want to figure them out.
1. seat heating is turning on without clicking on the button, but not always it's random. Often on passenger seat some time on driver side to. I try to disable fuse but it also for 4x4 so it's not an option.
2. My engine idle RPMs is always higher that 1000. Maybe it is normal but want to be sure.
3. car cannot climb the hills here is the video.... car is just doing nothing to climb no rev up no trying just stall in middle. In my country there is some roads with hills like this and I want to visit that places.
4. Cruise control is working random to maybe it will start speed control in one click or after 20 -s try.
5.Is there any way to see soc? factory unis is replaced in my car with aftermarket radio. I have elm327 and tourque pro but can't find that option.
6. When monitoring with obd water temperature is always lower then it was on my other cars. its around 158-176F on other cars it was 200F.
YouTube......
View 2 Replies
What to look for. 2001 escape 3.0 starts and runs but it has a miss and no codes came up yet . the engine will rev up but it really takes time to idle down . don't matter if its cold or hot it just don't want to drop to idle as fast as it should.
View 4 Replies
Have a 2006 ford escape, at idle the engine will run around 1000 rpm's and then regularly dip down 500 rpm's. Through the intake i can here a distinct "thwap" when the RPM's dip.
Only codes are
P0113 and P2196
Problems accelerating sometimes, Took it too a shop they said bad exhaust valve on the backside of the engine either 1-2-3. They said needed engine work, but said they didn't know where the bad valve was so i don't even know how the made the determination. Vac gauge at idle also indicates bad valve.
However, when i give it even the smallest amount of gas possible the engine smooths out and vac gauge reads totally normal and steady.
View 7 Replies
I have a 2001 ford escape. Today it starts to miss and the engine lights starts flashing. It is never the same amount of flashes. Sometimes its 8 or 10 flashes. I counted up to 25 flashes one or twice It just shakes bad and that's when the flashing starts. When it starts to miss and vibrate, I can accelerate in passing gear and it smooths out. When you hold it at a constant speed it starts missing again. Cannot get a code with my reader. Someone told me a flashing light indicates a misfire. What may be causing this problem?
View 2 Replies
Well, not an escape, it is a mazda tribute. but it is the same thing as an escape. My sister just called. as she is driving down the road, if she lets off the throttle the engine will randomly die. it did it 2 times sunday, once yesterday, and once today, as she was talking to me. It will not die at traffic lights, just as you let off the throttle sometimes. today it did it at 45 mph. When it dies she just pops it in neutral, restarts it, puts it back in drive, and it is fine. No check engine light after restarting. What I should look at when she brings it over this weekend?
View 3 Replies
My daughter has a 2001 Ford Escape, V6, Automatic, 2WDR, 132,000 miles that is having starting problems. When you turn the key the engine will try to start. You have to push on the gas pedal to keep it running, it will not idle until it gets warmed up. If you try to drive it while cold, it has no power. Reading previous posts I have already replaced the spark plugs, intake gaskets, air filter, EGR, TPS, and fuel filter. Check for crack hoses / vacuum leaks. It is still not starting properly. No engine codes. New problem is oil light is flashing but the engine has oil. All of the gauges, lights, functioning normally. What do I try next?
View 1 Replies
2001 escape 3.0 engine is giving me a headache. It starts and will idle no problem but as soon as I step on the gas the engine sputters and coughs but it does race up. I put in new intake seals, new sparks plugs and a tps and cleaned the maf sensor. It shows no codes so what am I missing? Can it be a fuel system problem ?? what should I be looking for??
View 2 Replies
I am having some ( Bad Luck ) with my 02 escape I been getting random misfire codes started checking over o2 sensors first, replaced one on bank 1 downstream, I have screenshots to look over along with codes....
View 3 Replies
I have a 2009 Escape, 2.5l engine and manual 5 speed transmission, 205,000 miles. It has has an intermittent miss that has been getting gradually worse over the past 3 months or so. I've been seriously futzing with it for the past 2 months, so far no luck. Definitely worse when it's cold. Not noticeable at all in gears 1-3 (even when cold), noticeable in 4th, mostly between ~2000-2500 RPM, and pretty bad when cold in 5th in the same RPM range, still noticeable when warm. No service engine light until today (#1 misfire).
If I let the vehicle idle for 10 minutes or so, the miss is much less noticeable. Replaced the plugs, absolutely no difference. Bought one COP and cycled through all cylinders, no difference. Finally broke down and took it to the Ford dealership where I bought it new and had them do a power balance test, which isolated it to cylinder #1. Swapped the #1 and #2 injectors and took it back to Ford, still showing cylinder #1. Did a compression test, #1 and #2 both around 165lbs, #3 and #4 both around 185lbs.
I'm a electrical engineer, so I spent some quality time with an oscilloscope to compare the drive waveforms of the #1 and #2 cylinder COP and injector...both COP and injector drive waveforms look identical when comparing to #2 cyl. Tried heating the PCM, made no difference (engine was cold, PCM was hot).
So it finally DID throw a code today, cylinder 1 misfire. I'm thinking I can almost hear a miss at idle now. And listening to the valvetrain at idle, there is unmistakably more valve noise coming from the #1 intake area than the other cylinders, but not terrible.
View 6 Replies
I have a 2002 Ford Escape, 6cyl FWD... 110,000 miles.
About a month ago I started seeing a misfire, which of course usually is a COP issue. I should buy stock in whoever makes those. Anyway, the code according to parts store monkey was cylinder 2 misfire, so I replaced the COP. That made no difference. I also replaced the upper intake gaskets and the PCV valve while I was in there.
So I started monitoring when it would happen, and of course got the actual code rather than taking the word of the monkey at the parts store. The code is P0352 Primary / Secondary circuit malfunction.
So after some research I find it could be the harness, it could be the PCM. The question I have is this misfire seems to only be when the motor is started after it's hot. What I mean is I can drive to work 10 miles, no problem. I can drive to Orlando 100 miles away - no problem as long as I don't stop on the way. The only time the misfire happens is when I start the motor when it's hot. So if I drive 10 miles to the store, then drive home before the motor cools completely I'll be coming home on 5 cylinders. If I wait 2 hours between stop and start I never have a misfire.
Does that jive with a true electrical problem? I'm no expert, but I don't understand why driving for 100 miles is fine, but 10 miles, stop start and 10 more is an electrical problem.
View 14 Replies
I have a very Big problem with my Ford Escape 2002 I have this problems code: P0305 accuses Cylinder #5 P0306 accuses Cylinder #6.
I already change the gasket i buy the felpro Kit, and i Also replace all the sparks and spark plug boots, I clean the air sensors and i also replace the EGR, i try to switch cables, and all is the same the car start buy when i accelerate it just go off, i don't know what can i do next, somebody told me to change the fuel injector, i take the pressure in both spark holes the number 4 was 150 and the 5 and 6 was 120, No leaks oil. My car is a Ford Escape 2002, XLT 3.0 4x4
View 2 Replies
My wife has a 2004 escape v6 (3.0L). The valve cover seal was leaking so I decided, why not change the plugs since I'm already going to have the intake manifold off.
I got down there, replaced the seal (just the front side, didn't want to disassemble something that wasn't broke) and then replaced all 6 plugs and boots (with springs). Fired it up and everything seemed fine. She went to drive to work and the CEL started to flash. I read the code and there were 4 (Don't remember exactly what they were), but it was a combination of things resulting from a misfire in cylinder 4. Since it was one of the front ones. I just pulled the plugged and replaced it hoping I had gotten a dud from the factory. Nope, still doing it.
I didn't take off the fuel lines, just the air intake on the top. I did not change the coils, but everything was running fine before I changed plugs so logic would dictate it is something I did. Only seems to misfire at higher speeds. Also, her battery light randomly comes on, but the battery and alternator test good. This has been happening a while.
View 4 Replies
I am having a lot of issues with my 2002 ford escape, a while if I drive the truck acts normal, but after driving it starts missing when beginning to accelerate at a dead stop check engine light starts flashing pulled codes coming up with #4 cylinder misfire and #5 cylinder misfire detected, also a catalyst system below threshold bank 2, I have had the vacuum lines repaired and still no changes and went through and changed my grade of fuel from regular unleaded fuel to premium fuel, actually went worse with using premium fuel. I was thinking of replacing all three coil on the front of the motor, putting new plugs in it and seeing what that does.
View 2 Replies
