Ford Escape / Hybrid :: 2001 - V6 Idle When It Gets Cold Outside
Nov 30, 2015
I have a 2001 Escape, V6 engine and I guess it really does not like it when it's cold outside. Usually the car runs just perfect but when the winter arrives and temps drop into the 20s the truck does not want to run idle right when I first start it. I have tried by stating it without touching the gas pedal. And also by pushing it all the way down and then releasing it. I don't know which method is the right one, but it doesn't seem to make a difference. It takes some time and eventually after about 5 miles of driving it will act normal again. What could I do to fix that?
View 9 Replies
Advertisement
I'm needing cold engine misfire. 2001 escape 3.0 engine 190300 miles on it. I changed the plugs, cleaned the fuel injectors, new air filter, new fuel filter, cleaned the pcv valve and new ideal control valve. When the engine is cold it starts right up but wont idle right and misfires sputters some to but run the rpm's up and it smooths out. drop to idle and it misses. Now when the engine gets to operating temp it seems to run fine. What am I overlooking to find the problem?
View 5 Replies
I have a 2001 Ford Escape. When started cold, it revs up to abt 3000 rpm. Slowly drops back to about 1000 in abt 10 secs. When the engine is hot, it often wants to idle 2500+ rpms and I have to really step on the brakes to slow the vehicle. When I disconnect the IAC the engine dies. When it is revving high, I can disconnect and reconnect the IAC quickly, and the idle will drop back down for a few minutes, until I step on the accelerator, then start climbing again. It seems to be a lot worse when hot.
I replaced the IAC and TPS about 20k miles ago and thought it was fixed, but the problem has returned. At that time, I could tap on the IAC and it would "get well" for a while. Tapping on this one doesn't seem to change anything. No CEL, engine runs smooth, and I don't notice any air leaks (none that I've found, at least).
View 8 Replies
I've got an 01 Ford Escape 4 cyl 5spd awd, it idled low when its warm, revs between shifts and if you put it in nuetral and let the clutch out when you're moving it revs to 3500rpms and just sits there until you stop or push the clutch back in. I've replaced the iacv and the pcv valve, elbow and hose, and the tps. What to look at next?
View 4 Replies
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
View 14 Replies
I've read quite a bit in various threads about the large vacuum elbow collapsing, causing erratic idle speeds. My 2001 3.0 had that issue int he past. I shoved a 1/2" copper 45 degree elbow inside of the rubber elbow, and the problem was solved... until a few days ago.
We're now getting into the hot part of summer here. I've notice the same symptoms are beginning to return, once the engine compartment gets hot. My question is... is the large vacuum line a "hard line" all the rest of the way to the engine, or are there other places along it's length that can also collapse under vacuum?
View 3 Replies
I have a 2001 Ford Escape, and since the colder weather set in it is tacking below 1 and 'jumping' when idle. When accelerating and/or once the heat gauge has reach midway, the car is fine. I added a bottle of gas additive to the tank 3 weeks back, but the problem persists. The engine light is on but no code is registering.
View 2 Replies
Ok, so I've got a little of an odd issue. It seems that no matter what I do, the AC is always active. Today I reverse flushed the heater core in my 02 Escape, and verified all hoses were clear. I replaced the thermostat housing (other thread) along with a new thermostat.
But, when I run the car, even with the heat full up and the selector set to the defroster and floor, the ac still blows ICE cold. It seems like it is still engaged no matter what. Winter is coming and I dont want my daughter to freeze (her truck).
View 2 Replies
Trouble starting our 2008 escape after she has been sitting for atleast 4-5 hours (or more) We can get it going usually but we have to attempt several times before it 'catches'. After running and turning off, it starts no problem. Have replaced mas and didn't work. No 'check engine soon light' so just trying to narrow down the problem. Have replaced the fuel filter and all the spark plugs. Love my escape but not when it doesn't start!!
View 9 Replies
I have the 2.0L 4 cyl. engine (2001 XLS Manual 114k miles). Runs fine when cold but once the engine gets warmed up it starts idling really low. I mean so low that the RPM gauge looks like the engine is turned off, although it hasn't completely stalled (yet). The engine will kind of stumble here and there and occasionally jump up to the normal RPM. Not rough really (in fact it's hard to tell if the engine is on when it's so low) but something is obviously wrong. The check engine light is not on (assume no codes?).
Also when I'm driving I can feel that the RPM's are unstable and erratic. You know, it feels like I'm pushing and releasing the pedal very slightly even though I'm not moving it.
I replaced the spark plugs and fuel filter since they needed to be done anyway. I checked the vacuum lines and they all seem good. I replaced a few deteriorated lines even though they were holding vacuum. None of this changed anything.
So now I'm looking at more expensive stuff like the throttle position sensor, idle air bypass valve, EGR, MAF, etc. Where I should start? Is there anything that I can actually test to see if it's working or do I just need to start replacing parts until I find the problem? I guess cleaning the MAF and IAC might be starting points that don't cost anything (that IAC looks difficult to remove though).
I'm kind of thinking it's the TPS since it feels erratic at speed. However, I have never had a bad TPS cause a slow idle before. I have had it cause rough idle and such but not slow. Can it do that? What about the MAF sensor?
View 14 Replies
My 12 Escape with the 3.0, shifts fine in warm weather or in cold weather when warmed up. But first thing on a cold morning she's a bit of a screamer getting into the next gear. Is this a signal of something about to go wrong? Is there an easy adjustment? Or this is the way of it and it is fine......
View 14 Replies
I have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 Replies
My wife has her 03 escape v6. It has a very rough and low idle. On start up it idles nicely and then the idle drops and pulses if that makes any sense. I've pulled I think its the idle control sensor. It killed the engine as soon as I did. I've cleaned the throttle body.
View 2 Replies
I test drove 2 2005 escape limited v6 2wd today. Both of them were pretty loud in the cabin at idle. The noise and vibration did lessen after the car started to move. Is this normal for escapes or does this indicate a problem somewhere? Like engine or transmission mounts.
View 2 Replies
2 questions regarding my 2005 Mariner 3.0L, as follows:
1. After a cold start (in the garage, so not freezing cold) the water pump belt - not the serpentine belt - squeaks for 15 - 20 seconds; ambient temperature doesn't matter. I had put a new belt on about a year ago, then this began 6 or so months later. Thinking I may have a defective belt, I replaced it again about 3 months ago, but the squeaking has continued - starting immediately after the replacement. My analysis is that the water pump bearing is going south. I've noticed that it is taking a little longer for the squeak to go away in the past few weeks, so it's probably getting worse, altho no leaks at this point. So the question is, so any other reason this is happening?
2. Assuming I do need to replace the WP, I bought a new one from the local parts house. I have a shop manual for the car, which tells me to remove the thermostat housing, hose connection to the WP, etc., and then remove the WP by removing just 3 bolts. However, the replacement part is just the front of the housing with the impeller and pulley included, so there are a half-dozen or so bolts that hold this new part onto the WP housing. So, doing this change-out? Will the front of the WP housing come off by itself without disconnecting the hose, etc., or do I first have to remove the whole WP and then take it apart to replace the impeller and front cover? I can't really tell from the pic in the shop manual, and it doesn't address dis-assembly of the WP.
Also, I'd like to just remove the belt w/o cutting it and having to buy a new one. Can I do this by just loosening the WP bolts? (I know how to re-install, obviously.)
View 6 Replies
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
View 11 Replies
I have been having this problem with Gf's car for a few months it is a 06 3.0 escape with 141K on the clock the car seems to run ok except at red lights and when in drive it seems to idle like its just about 100 rpms low when I give it a little gas just a touch it smoothes out. if I put it in neutral the car smooth's out but in drive when you come to a stop light or stop sign you can feel the rough or low idle in the steering wheel. She is nagging me and it has been very cold here in Pa and I'm trying to wrap my head around if it is a cold thing or just a coincidence. I'm fairly good at wrenching and I just need some things to look for as when you start the car up cold it idles fast like 12 to 1300 rpms and then drops to about 900 and in drive it seems like maybe it's about 600 to 700 rpms. but where to start to look Is it a sensor, vacuum leak ?
View 6 Replies
When started very high idle after hitting gas pedal sometimes it will lower idle sometimes not,,then holding pressure on gas pedal it has very bad surging ... Any guesses what might be and possible cost fix?? I am no mechanic,will have to take it somewhere...90,000 miles on it..
View 3 Replies
I have several problems with my 06 FEH maybe some of you had same issues. I have imported this car from new york in my country 1 month ago, this is first Ford for me. Love this car but there is some issues and want to figure them out.
1. seat heating is turning on without clicking on the button, but not always it's random. Often on passenger seat some time on driver side to. I try to disable fuse but it also for 4x4 so it's not an option.
2. My engine idle RPMs is always higher that 1000. Maybe it is normal but want to be sure.
3. car cannot climb the hills here is the video.... car is just doing nothing to climb no rev up no trying just stall in middle. In my country there is some roads with hills like this and I want to visit that places.
4. Cruise control is working random to maybe it will start speed control in one click or after 20 -s try.
5.Is there any way to see soc? factory unis is replaced in my car with aftermarket radio. I have elm327 and tourque pro but can't find that option.
6. When monitoring with obd water temperature is always lower then it was on my other cars. its around 158-176F on other cars it was 200F.
YouTube......
View 2 Replies
When I start my 2003 Escape 3.0, the rpm's shoot up to about 3000rpms. After a few seconds they drop to about 2000 and slowly creep back up to 3000. When I put in gear, I don't even have to step on the gas and my vehicle goes. It maintains between 1500-2000rpms as I'm driving. When I come to a red light or stop sign, it lurches like it wants to go even though I have my foot on the brakes. I've replaced the IAC valve, TPS, had it checked for vacuum leaks, PCV valve replaced. I'm at a loss as to what it could be.
View 3 Replies
Posted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 Replies
