Ford Escape / Hybrid :: 2001 V6 - Rough Start / Cranks For A Few Seconds Then Fires Up
Oct 7, 2015
Alright I thought changing a fuel filter was fool proof but I changed the fuel filter in my 2001 escape v6. awd and now for some reason it wont start right up like it used too before the filter change. It cranks for a few seconds then fires up and runs perfectly fine it sits for a few hours same issue where as before the filter change it fired up fine every time, what did I do wrong. 2001 ford escape...
View 1 Replies
Advertisement
So it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
View 4 Replies
I am having a problem starting my Escape. It ran fine when i parked it. Now it turns over but wont start.
It turns, almost catches, then turns slower. White smoke comes out of the exhaust, which means it is getting fuel i think. When I crank it all the dash warning lights go off. I tried the spare key. I tried pushing the gas pedal. No codes on the scanner. I switched the fuel relay (r3) with the fan relay (r4). I tilted the column a few times. Coils and wiring do not show any damage or wear. I opened the air filter with no change.
The only change i notice is that when turning the key has some resistance. It does not feel like it used to turn. This year I had to install a new battery and alternator. At 90k miles i gave it a tune up (plugs, boots and coils). It has 116k on it now.
View 12 Replies
Wifes Escape with the 3.0 has been progressively getting harder to start. It spins over just fine, but now takes between 3 to 8 seconds to actually fire. In the last six months the alternator, spark plugs, air filter have all been replaced. Engine runs perfectly, never stalls and seems fine in every other way. I've cleaned the throttle body and the IAC is working fine.
Did some troubleshooting and sure enough, we are getting no spark for a few seconds and the engine runs fine when it finally gets spark. Would this be the crank position sensor? Cam position sensor causing this? Not sure what is supposed to happen during the starting sequence in regards to what sensors are in being read by the PCM and then enabling spark.
View 1 Replies
2 questions regarding my 2005 Mariner 3.0L, as follows:
1. After a cold start (in the garage, so not freezing cold) the water pump belt - not the serpentine belt - squeaks for 15 - 20 seconds; ambient temperature doesn't matter. I had put a new belt on about a year ago, then this began 6 or so months later. Thinking I may have a defective belt, I replaced it again about 3 months ago, but the squeaking has continued - starting immediately after the replacement. My analysis is that the water pump bearing is going south. I've noticed that it is taking a little longer for the squeak to go away in the past few weeks, so it's probably getting worse, altho no leaks at this point. So the question is, so any other reason this is happening?
2. Assuming I do need to replace the WP, I bought a new one from the local parts house. I have a shop manual for the car, which tells me to remove the thermostat housing, hose connection to the WP, etc., and then remove the WP by removing just 3 bolts. However, the replacement part is just the front of the housing with the impeller and pulley included, so there are a half-dozen or so bolts that hold this new part onto the WP housing. So, doing this change-out? Will the front of the WP housing come off by itself without disconnecting the hose, etc., or do I first have to remove the whole WP and then take it apart to replace the impeller and front cover? I can't really tell from the pic in the shop manual, and it doesn't address dis-assembly of the WP.
Also, I'd like to just remove the belt w/o cutting it and having to buy a new one. Can I do this by just loosening the WP bolts? (I know how to re-install, obviously.)
View 6 Replies
I have the notorious PO171 and PO174 codes on my 2003 5.4L that come back whenever I erase them. I cannot figure out the problem. Whenever I start the truck it cranks for 3-4 seconds before it finally fires, then rpm's are very low, then they finally pick up. I have noticed a loss in power as well. I have completed a full tune-up (spark plugs, coils, boots, filters, etc.)
I have checked the vacuum and PCV lines numerous times, I have yet to find a leak. MAF appears clean. I am running a K&N CAI setup. O2 sensors a good, replaced the gas cap. The only other problem I can see is a bad PCV valve? I hope it isn't a manifold gasket. The truck has been very well maintained and still looks brand-new throughout at 250,000 miles.
View 4 Replies
So my wife's 2005 escape currently will not start. It was running rough so we brought it in to the shop to have the codes read. There was a bad MAF sensor code so we brought it home and were gonna replace the part the next day. The next day rolls around and it refuses to start. Swapped out the spark plugs which was much needed, replaced the valve cover gasket, which had also gone bad, and put in a new MAF sensor. It still refuses to start. It will turn over, but never starts. Also, the sound as it turns over doesn't sound right. It's hard to explain what sounds off about it, it almost has a "soft" sound to it. I can try to explain better if needed.
View 6 Replies
My 2001 escape recently decided to act up, it was running rough for a little while and then it died and would only run intermittently after that. I found the #3 coil was bad and the egr valve was broken. I replaced those and now when it decides to run it runs smooth but when you give it has it bogs down and dies and doesn't want to run again for a while. I also put on a new fuel filter and the fuel pump sounds like its running good. I know I'm missing something here but I can't seem to figure it out. Also there are no DTC's at all. I really need this car to be back on the road again.
View 11 Replies
My daughter has a 2001 Ford Escape, V6, Automatic, 2WDR, 132,000 miles that is having starting problems. When you turn the key the engine will try to start. You have to push on the gas pedal to keep it running, it will not idle until it gets warmed up. If you try to drive it while cold, it has no power. Reading previous posts I have already replaced the spark plugs, intake gaskets, air filter, EGR, TPS, and fuel filter. Check for crack hoses / vacuum leaks. It is still not starting properly. No engine codes. New problem is oil light is flashing but the engine has oil. All of the gauges, lights, functioning normally. What do I try next?
View 1 Replies
My dad has an 2001 XLT 3.0 4x4 with 100,000 miles. He was having trouble with hesitation and decided to change the fuel pump. All went well and the Escape ran fine for a couple of weeks. The other day, he went to start it and nothing happened. One click and the gauges ran up and stuck. Battery was tested at Auto Zone and checked ok.
View 3 Replies
I'm trying to diagnose an issue my sister has been having on her 2010 with the V6. Dealer can't find anything wrong with it
She says when she stops to get gas, it has trouble starting back. Will crank, but not start. has to try it several times. Sometimes pumping gas will work. (Sounds maybe like IAC to me)
She says when she's driving, that sometimes it will quit. Best I can understand from her description, it's when she's off the throttle. She says most of the time it will start right back up then.
She also says sometimes when she's trying to crank it back, it acts almost like a bad starter, or battery. Starter getting slower, then speeding back up. Also says that sometimes it acts like it's low on power. She has to floor it to make it go.
My thoughts are IAC or faulty fuel pump?
View 5 Replies
i just rebuilt the motor in my 2002 ford ranger 3.0 and it wont start it cranks over but back fires and bucks alot. took the plugs out and it gets spark and fuel. when it sparks it sparks like multiple times.
View 3 Replies
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
View 14 Replies
I have a 2001 ford escape V6 3.0l. Dropped a new motor in it, got everything running fine. Surprisingly the most frustrating part was when we mixed up the order of the front 3 coils but we got it!
It drove "ok" for a week and a half. Then it started to shudder at 45-55 mph. Got it home that afternoon and started to diagnose why it would shudder. Suspect its not shifting right.We started to diagnose what was wrong, made some adjustments to IAC, MAF and checked a few other things. We then went to test drive, started up fine, drove up the driveway 50' and it died. It didnt sputter and die, it just lost all power and died.
Got it back in the garage and tried to get it started again. Turned Key... nothing. Dash lit up but starter and fuel pump didnt fire. Odometer reads ------. I can jump the starter by pulling the starter relay. Same for the fuel pump. I use a jumper wire between two pins and I can get the starter to crank and the fuel pump runs when I jumper wire the relay too. So I know its not a bad starter nor a bad fuel pump.
Odd part of everything is that It drove just fine that day (other than shuddering). Then started just fine, then died. When it died we were making a sharp left turn in the driveway. We've messed with the steering wheel because it was "accidentally" put upside down when we dropped in the new engine. Could something have grounded out in the steering wheel? Air Bag? Maybe a problem in the clock spring? What would stop it from The fuel, starter and spark all at the same time? Bad PCM? Grounding issues?
View 8 Replies
94 Saab will not start in the mornings , it cranks but wont fire , runs fine later in day with no problems at all . Than next morning a repeat performance of not starting.
View 10 Replies
My 2006 Azara has had a no start problem since about a year after we bough it new. The condition is intermittent and is not dependent on outside temperature, humidity or other conditions, It happens when the engine is cold or hot. Sometimes the problem goes away for a week or so then it comes back. It happens with either key.
The engine cranks over but does not start. Usually resolve it by sitting for 10 - 15 seconds then trying again. Sometimes have to do this two or three times before it fires. All other electrical items work ok and the battery has no problem powering accessories. I've had it into the dealer however because it is difficult to replicate, they have a hard time repairing the problem. The first time they neutralized the immobilizer and re-programmed it. The second time, I got a check engine light and they replaced the immobilizer. But the problem continues.
View 6 Replies
On my new/used 2008 Escape XLT 2.3L 2WD. It flashes every two seconds, like the manual says. Lower left corner of instrument cluster.
But I don't recall the warning light flashing when I test drove it. But I did push the buttons on the keyfob and various places on the dash/instrument cluster to see what they did...
Is the anti-theft system an on/off affair? If so, how do I turn it off?
View 1 Replies
My 96 Town and Country won't start. It turns over and fires for about 1-2 seconds max. After that it only turns over, no fire. The key sign/symptom is that the odometer and PRNL do not light up. This is very sporadic. Sometimes months and months apart. I unhook the battery in an effort to reset the computer. Sometimes it works in 1/2 hr. Sometimes several hours. So I don't think it resets but I still do it anyway. I have replaced the computer but no luck. Could it somehow be the dash cluster?
View 8 Replies
My wife has her 03 escape v6. It has a very rough and low idle. On start up it idles nicely and then the idle drops and pulses if that makes any sense. I've pulled I think its the idle control sensor. It killed the engine as soon as I did. I've cleaned the throttle body.
View 2 Replies
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
View 11 Replies
I have been having this problem with Gf's car for a few months it is a 06 3.0 escape with 141K on the clock the car seems to run ok except at red lights and when in drive it seems to idle like its just about 100 rpms low when I give it a little gas just a touch it smoothes out. if I put it in neutral the car smooth's out but in drive when you come to a stop light or stop sign you can feel the rough or low idle in the steering wheel. She is nagging me and it has been very cold here in Pa and I'm trying to wrap my head around if it is a cold thing or just a coincidence. I'm fairly good at wrenching and I just need some things to look for as when you start the car up cold it idles fast like 12 to 1300 rpms and then drops to about 900 and in drive it seems like maybe it's about 600 to 700 rpms. but where to start to look Is it a sensor, vacuum leak ?
View 6 Replies
