I have a 2001 Ford Escape 3.0 4WD, it has a rattle in the motor and no acceleration... Bought the escape with the rattle when you start it up and put into drive it wont accelerate. Transmission is good...
View 3 RepliesI've got an issue on my Escape, and I'm at a dead end. '01 XLT V6 150K miles.
About a week ago, driving to work, it started stuttering or misfiring while accelerating up inclines. Cruising and idle were smooth with no issues. I found that if I let off the gas as it was stuttering, it would stop, and then I'd give it gas again, and it would be fine. It was pretty intermittent.
Opened the hood and the large vacuum hose that goes from the top of the intake down to the PCV, has an L boot that connects it to the intake. That boot was collapsed down on itself while the motor was running. It went back to normal when I shut it down. I felt the boot and it was very thin and worn out, so I replace the whole two piece hose, along with the PCV valve. The old PCV came out and was rattling, so I believe it was ok, but I installed a new one anyway.
Drove it after that and it still had the stutter. It was now also doing it just barely at idle. I'd hear the motor miss, and it would really start when I would give it gas. I thought it was still a vacuum issue, and that there were probably other bad hoses. I found two. There's a small hard plastic line that comes off the air intake hose from a T, and those lines go to the camshaft covers. The hard lines go to rubber boots on the cover, and the one in the back was in two pieces. Replaced it. No change.
The other line is a small rubber line that comes off a round component, (I still haven't found out exactly what this part is called), that is bolted to the drivers side shock mount, and has a couple soft lines coming off of it. One of the lines goes over the top of the motor and ties into a T right where that large PCV hose goes into the intake. The part is circled in red, and the arrows point to the hose in the attached pic.
Where the blower motor resistor is located on the '05 model.
View 11 RepliesBlower motor only seems to be working on the 3 & 4 position? Resistor bad? What is the location?
View 1 Replies2007 Ford Escape XLT V6, ~60K miles .... My wife has this rattle in her escape, has had it about a month now. The rattle happens when idling, is less noticeable when driving the car, but might just be drowned out by road noise, etc. Revving the engine in neutral doesn't seem to affect the rattle at all as far as I can tell.
I listened around the engine compartment with a stethoscope for awhile and couldn't pinpoint anything so I told her to bring it in and have it looked at. She brought it in to "Brake King", they do full service mechanic work, but i'm not sure how great they are, but they are flexible about bringing the car in and looking at it right away and my wife can't be without her car for very long since she uses it for work. They said it need the sway bar rods and bushings replaced (they did this and the noise didn't go away). I was pretty suspect about it since the rattle happens when idling, but i'm no expert so I figured they knew what they were doing.
We brought it back and the guy said that the noise was internal to the engine and asked about where we get the oil done. (I do the oil myself and always use Mobil 1, I really don't think it is an oil issue. Maybe the oil filter since we don't change that every time, but again... They did a free synthetic oil change + filter change and that didn't work.
All the while i've been doing research and I decided to go ahead and remove the drive belt to see if the noise would go away when I did ( this whole time I was suspecting something on the drive belt). So I removed it and the noise did go away for the minute or so I ran it without the belt. This pretty much confirmed to me that it was something on the drive belt. I replaced the tensioner since I read that that could be a suspect and they are "relatively" cheap and easy to do. That did NOT work. (I also broke the bolt that holds it on and had a helluva time trying to find a replacement, but that is a whole other story).
So while I had the splash guard off, I listened some more. The rattle really seems to me to be coming from the crankshaft pully area rather than from the A/C compressor area or the alternator area. If it was the C/S pulley, wouldn't it still make the rattle even with the belt off? Looking in the Haynes manual, the C/S pulley doesn't necessarily look like that easy of a replacement (especially if I'm not sure it will actually fix the problem). Anyny opinions as to whether that might be the problem, and if so if a DIYer can do the replacement?
Here is the video. When watching it live, I swear I see a bit of a wobble on the pulley compared to the other pulleys on the belt line, but in the video, you can't really see it...
Video : Mystery rattle ford escape 2007 - YouTube
I have a 06 Mercury Mariner and this past week fuse #26 keeps blowing turning the HVAC blower motor off. I replaced the blower motor since i had one already in the garage and same thing is happening. The AC will run for awhile and in about 10/15 mins the fuse will blow. Fuse #26 is the Climate control system mode switch, are these known to go bad? Is this the part I should replace or look for other problems IE compressor?
View 2 RepliesI am pretty satisfied with the performance of my 2009 Ford Escape. Two years 51,000 miles after I find that the rear door does not open. Following threads of earlier Escape models I find how to remove the inside panel and open it manually. After a thorough study all I need is a replacement latch motor. The plastic latch cover has the following number GA6 GF30.
View 14 RepliesNot always & seemingly at random. Just like at startup after battery reconnect.
Most searches come back only with incidents at startup only. Recommendations say battery &/or alternator. Battery is Optima Red that's been in there maybe 6-7 years and all connections are clean & reads 12.48 at rest.
Alt is a AC Delco new unit replaced 20k or so ago & reading 14.24 at idle with or with out any accessory drain on the system or RPM.
Troubling thing is a code for coil misfire on # 5 which put it into limp mode (I erased & so far hasn't returned) & some comm issues with the Inova 1403 that I'm using.
The wifes 2011 Escape battery was dead. Charged it and also found that the rear wiper motor was not working. But it was very hot to the touch even with the car shut off. It was killing the battery. I wonder if the wiper needs to complete it's cycle to shut down. It won't work. Again it gets very hot even with the car shut down for the day I believe killing the battery. Also how can the wiper motor assembly be removed?
View 3 RepliesA couple of weeks ago I got a check engine light. Pulling the codes I saw that it was a p0304 and sometimes a p0316. The first time this happened I check the spark plug cables and one was loose (cycylinder 4). Then last week my fuel pump died. since then I have gotten the two codes on a somewhat continous basis. I replaced the plugs (needed to anyway) and the problem did not go away.
The odd thing is that the check engine light does not come on at idle. IT only comes on after the motor is at a higher rev. The replaced plugs looked pretty normal, but the cylinder 4 plug had some carbon deposits. I am currently running injector cleaner in the gas. I may go ahead and replace the plug wires since the current ones are high mileage and it is not an expensive fix.
2004 Escape 2wd 6 cylinder 170k miles. Intermittent clunk/rattle sound when hitting bumps while going straight and especially turning right. I felt a slight bumping in passenger side floor board. Inspected everything. All looks good and tight- no signs of loose hardware, worn ball joints or tie rods. Only thing I noticed was a slight rub mark (missing paint) on the lower control arm under the sway bar on drivers side. And noticed the rear bushings on the control arms are tearing.
Not collapsing but with the tire removed and suspension hanging at full droop you can see tears in that rear bushing on both sides. We painted the arm and sway bar in the rubbing location to see if it makes a mark there again after driving it a few days. Question is do you think that the rear control arm bushings could be allowing enough movement to contact the sway bar or make the noise? The bolts are tight. Has newer Moog struts and newer swaybar end bushings, possibly sway bar hold down bushings too- (they look pretty good).
I have a 2006 Ford Escape that's turning into a mystery. Over the last few months the warning lights have been reporting issues with the overdrive. I've taken it to the mechanic who hasn't been able to identify the issue.
He's cleared the issues from the ECU, and the car doesn't complain for about 2 weeks, then it reports a different issue related to the overdrive (eg: OD or transmission).
Possibly related, the car occasionally loses power on acceleration. When taking off from a stop, it'll be really underpowered while getting up to speed. This only happens occasionally.
Is it a part failure, or could it be electrical or related to the sensors?
I have a 2001 Escape, V6 engine and I guess it really does not like it when it's cold outside. Usually the car runs just perfect but when the winter arrives and temps drop into the 20s the truck does not want to run idle right when I first start it. I have tried by stating it without touching the gas pedal. And also by pushing it all the way down and then releasing it. I don't know which method is the right one, but it doesn't seem to make a difference. It takes some time and eventually after about 5 miles of driving it will act normal again. What could I do to fix that?
View 9 RepliesThe cruise control has not worked on my 2001 escape since i bought it a few weeks back. i checked the usual culprits and everything is good. i plugged my scanner in and got a control module code.
c1945- park switch indicates park with vehicle moving.
I did do some live data testing and it does infact show park when in gear. the display on the dash shows the proper position.
I am almost certain this is the issue with my cruise. Where this sensor is? Doing a parts lookup isn't showing much.
Is it possible to replace the main bearings in a 2001 Escape 3.0 with the engine in the vehicle?
View 1 RepliesWhat to look for. 2001 escape 3.0 starts and runs but it has a miss and no codes came up yet . the engine will rev up but it really takes time to idle down . don't matter if its cold or hot it just don't want to drop to idle as fast as it should.
View 4 RepliesI have a 2001 escape. The red brake warning light in the dash is on. I have changed the low brake fluid sensor and disconnected the parking brake switch . It is not on when first started but comes on shortly after starting to drive (within 100 feet). Do these things have a proportioning valve and a sensor in it?
View 2 RepliesI own a 2001 V6 Ford Escape XLT, although that's already likely far too much information for this weird issue I'm having. It's been going on for a while now, steadily getting worse.
The issue is that the driver's side window will easily roll down, but becomes unresponsive when I click the button to bring the window back up. At first, I could simply press the button a bunch of times and eventually find success. Now, if the window is rolled down, I have to get out of the car and move the door back and forth while furiously pressing the button. Eventually, I'll find a spot in the door's swing where the button will finally make a connection with *something* else inside the door and roll up the window.
What could the issue be? Seems like a clear electrical issue, and something that would occur in the joint of the door, since opening and closing the door is the only way to eventually establish an electrical connection.
A couple weeks ago I had to have both lower ball joints replaced on my '01 XLS 4WD with the 6 cylinder engine. The garage's alignment machine was on the blink, so the mechanic told me to it woudl be fine to drive, and to bring it back this week when the machine was fixed.
The Escape seemed to drive fine until today, coming home from work, the Escape veered slightly to the right, and there was a brief sensation in the steering wheel as if it had been disconnected, as if something slipped. Then the steering was back, and although I was tracking straight down the highway, I noticed the steering wheel was turned to the left. It seemed to steer fine, although I had slowed way down.
I have a 2001 Escape 3.0 l 6 cyl. She stalls or almost stalls every time I fuel up. I found if I turn key but not to start, it only severely sputters and usually doesn't stall. Replaced EVAP canister (and all but dust separator inside), fuel pump, EGR valve, pcv tube, iac, upper gaskets, valve cover gaskets, seals, spark plugs, fuel/air filter, evap purge valve, fuel filler cap, ftp sensor, all ignition coils, checked for clogged fuel filler neck, fuel/vent hoses from/to evap canister...nothing worked.
There is a hose I cant get to that ends unattached just past fuel tank and near fuel vapor(?) "tee" under car. Seems to come from fuel tank. What is it? Just an overflow vapor hose? Should it be attached to something? Anyway, I suspect fuel vent hose or valve on top of fuel tank since my options are limited now. Have it running great (except this issue) with 260,000 miles so really don't want to spend mucho $$. No codes thrown.
Vehicle: 2001 Escape 3.0L V6
I'm listing here the obvious that has been changed already:
1) Valve cover gaskets
2) Oil pan gasket
3) Timing chain cover gasket
4) Upper and lower manifold gaskets (not oil related but changed)
5) PCV valve
6) Washed engine twice to remove everything and make sure nothing else burning
Problem: I still have a small leak from the top that causes smoke near or around the #4 COP on passenger (left side of the motor). But we do see some oil coming from near the PCV valve. It makes no sense and after reading what caused smoke on that side of the vehicle I changed the Timing chain cover gasket (which were finished anyway) and while was at it the oil pan but to no avail. Smoke and leak still there.
Probably not: I know that it is not the head gasket because there is no sign at all; I've never lost a drop of coolant and there is no smoke from the exhaust in back.
Suspicion: Could it be the oil separator where the PCV valve connects and makes it's way around to the other side? Is there something I am overlooking? There can't be many other places for an oil leak like that.
Coincidence ? : Even after changing all the COPS and spark plugs I found oil in the #4. However smoke was there before. I thought maybe a cylinder gasket I got second opinion from my mechanic says no not cylinder...
Engine runs well except for misfire in #4 but comes and goes. I think when oil builds up.