Ford Escape / Hybrid :: 2001 - No Start When Turned Key / Dash Lit Up But Starter And Fuel Pump Did Not Fire
Sep 3, 2015
I have a 2001 ford escape V6 3.0l. Dropped a new motor in it, got everything running fine. Surprisingly the most frustrating part was when we mixed up the order of the front 3 coils but we got it!
It drove "ok" for a week and a half. Then it started to shudder at 45-55 mph. Got it home that afternoon and started to diagnose why it would shudder. Suspect its not shifting right.We started to diagnose what was wrong, made some adjustments to IAC, MAF and checked a few other things. We then went to test drive, started up fine, drove up the driveway 50' and it died. It didnt sputter and die, it just lost all power and died.
Got it back in the garage and tried to get it started again. Turned Key... nothing. Dash lit up but starter and fuel pump didnt fire. Odometer reads ------. I can jump the starter by pulling the starter relay. Same for the fuel pump. I use a jumper wire between two pins and I can get the starter to crank and the fuel pump runs when I jumper wire the relay too. So I know its not a bad starter nor a bad fuel pump.
Odd part of everything is that It drove just fine that day (other than shuddering). Then started just fine, then died. When it died we were making a sharp left turn in the driveway. We've messed with the steering wheel because it was "accidentally" put upside down when we dropped in the new engine. Could something have grounded out in the steering wheel? Air Bag? Maybe a problem in the clock spring? What would stop it from The fuel, starter and spark all at the same time? Bad PCM? Grounding issues?
View 8 Replies
Advertisement
I have a 2004 Escape, 4x4, V6 with 116k on it. Recently it won't start until it's sat for a few hours. I'll drive it for a couple of days without a problem and then it will refuse to start. The Battery is strong, the starter is trying to turn it over but it won't fire up. I've seen several other posts with Escapes having this same issue but none have given a resolution. I'm figuring it may be the fuel filter, the fuel pump, or the computer control.
View 14 Replies
2009 Ford Focus. Six months ago got in car returning from 60 mile trip. Turned ignition key heard fuel pump hum but no juice to ignition. (Not anti-theft lockout--security light behaved normally.) Would not take jump. Ford Roadside assistance tried everything else possible. Nothing. Towed to nearest Ford dealer. On arrival, car started immediately. Took to local Ford dealer who found absolutely no problems but ran TSB 10-21-8 reprogram PCM--test OK. Had no further problems with car until a week-and-a-half ago--same thing happened. Car towed to dealer again. Started immediately at dealer! Picked up from dealer, that night same thing happened. Did not phone roadside assistance--after 45 minutes car inexplicably started. That was a week ago. No problems since then. Feeling a little panicky w/car that may fail at any time--winter coming.
View 5 Replies
Wifes Escape with the 3.0 has been progressively getting harder to start. It spins over just fine, but now takes between 3 to 8 seconds to actually fire. In the last six months the alternator, spark plugs, air filter have all been replaced. Engine runs perfectly, never stalls and seems fine in every other way. I've cleaned the throttle body and the IAC is working fine.
Did some troubleshooting and sure enough, we are getting no spark for a few seconds and the engine runs fine when it finally gets spark. Would this be the crank position sensor? Cam position sensor causing this? Not sure what is supposed to happen during the starting sequence in regards to what sensors are in being read by the PCM and then enabling spark.
View 1 Replies
A friend has 2005 escape 3l. He called me yesterday saying that he needed replacing his fuel pump.
Before I got to his place he had already replaced the fuel filter...
We got the pump replaced, and when we went to start the vehicle, it still wouldn't start.
We double checked to make sure everything was connected and plugged in and it was. We checked all fuses, and they were all good.
This morning I am going to try jumping the relay and see if that does anything. What else to check?
View 3 Replies
I am running into some issues with my 2011 Escape 2.5L. I am pulling a total of 7 codes. Two codes keep repeating, which those are P0455 and P0457. And I am also getting a C1963. Accompanying the engine codes, my HUD is displaying "Check Fuel Inlet" when I first turn the vehicle on.
View 10 Replies
The connector is near the floor (that's the gas pedal, in the picture). I've slid back the red clip on both, but the connector still will not separate. Is there a trick?
2001 Escape V6....
View 3 Replies
2 questions regarding my 2005 Mariner 3.0L, as follows:
1. After a cold start (in the garage, so not freezing cold) the water pump belt - not the serpentine belt - squeaks for 15 - 20 seconds; ambient temperature doesn't matter. I had put a new belt on about a year ago, then this began 6 or so months later. Thinking I may have a defective belt, I replaced it again about 3 months ago, but the squeaking has continued - starting immediately after the replacement. My analysis is that the water pump bearing is going south. I've noticed that it is taking a little longer for the squeak to go away in the past few weeks, so it's probably getting worse, altho no leaks at this point. So the question is, so any other reason this is happening?
2. Assuming I do need to replace the WP, I bought a new one from the local parts house. I have a shop manual for the car, which tells me to remove the thermostat housing, hose connection to the WP, etc., and then remove the WP by removing just 3 bolts. However, the replacement part is just the front of the housing with the impeller and pulley included, so there are a half-dozen or so bolts that hold this new part onto the WP housing. So, doing this change-out? Will the front of the WP housing come off by itself without disconnecting the hose, etc., or do I first have to remove the whole WP and then take it apart to replace the impeller and front cover? I can't really tell from the pic in the shop manual, and it doesn't address dis-assembly of the WP.
Also, I'd like to just remove the belt w/o cutting it and having to buy a new one. Can I do this by just loosening the WP bolts? (I know how to re-install, obviously.)
View 6 Replies
Im noticing my mpg dropping in the past couple of months. I usually get 19 or 20 in town, and up to 23 on the highway. Now im lucking if I get 16 or 17mpg.
I have a 2001 escape XLT. 6cyl 4x4.
I changed the spark plugs, coils and fuel filter about 3 years ago (almost 40k miles ago).
The car starts fine, seems to idle fine, seems to accelerate ok. The only thing that is off is the MPG.
I dont just want to throw money at parts. Which one should I replace?
View 5 Replies
My car is almost turning on. It goes all the way but then just doesn't start. The fuel pump is working, can hear it. We checked for spark and there is. we sprayed that carburetor or whatever it is in the air intake thing too and it still didn't start. My buddy is saying that it has to be a sensor. Either O2 or crankshaft something sensor.
View 13 Replies
My daughter has a 2001 Ford Escape, V6, Automatic, 2WDR, 132,000 miles that is having starting problems. When you turn the key the engine will try to start. You have to push on the gas pedal to keep it running, it will not idle until it gets warmed up. If you try to drive it while cold, it has no power. Reading previous posts I have already replaced the spark plugs, intake gaskets, air filter, EGR, TPS, and fuel filter. Check for crack hoses / vacuum leaks. It is still not starting properly. No engine codes. New problem is oil light is flashing but the engine has oil. All of the gauges, lights, functioning normally. What do I try next?
View 1 Replies
My dad has an 2001 XLT 3.0 4x4 with 100,000 miles. He was having trouble with hesitation and decided to change the fuel pump. All went well and the Escape ran fine for a couple of weeks. The other day, he went to start it and nothing happened. One click and the gauges ran up and stuck. Battery was tested at Auto Zone and checked ok.
View 3 Replies
Alright I thought changing a fuel filter was fool proof but I changed the fuel filter in my 2001 escape v6. awd and now for some reason it wont start right up like it used too before the filter change. It cranks for a few seconds then fires up and runs perfectly fine it sits for a few hours same issue where as before the filter change it fired up fine every time, what did I do wrong. 2001 ford escape...
View 1 Replies
I'm trying to diagnose an issue my sister has been having on her 2010 with the V6. Dealer can't find anything wrong with it
She says when she stops to get gas, it has trouble starting back. Will crank, but not start. has to try it several times. Sometimes pumping gas will work. (Sounds maybe like IAC to me)
She says when she's driving, that sometimes it will quit. Best I can understand from her description, it's when she's off the throttle. She says most of the time it will start right back up then.
She also says sometimes when she's trying to crank it back, it acts almost like a bad starter, or battery. Starter getting slower, then speeding back up. Also says that sometimes it acts like it's low on power. She has to floor it to make it go.
My thoughts are IAC or faulty fuel pump?
View 5 Replies
My daughter's boyfriend just bought a 2000 ranger with a 2.5. We just put a flexplate in it and it wouldn't start. Just turned over. Listened for the fuel pump and no noise. After a few minutes, it worked. He drove it home last night and said that it didn't want to work first try but worked with the second try. He drove it to church, 40 miles, and it sit for around two hours and wouldn't start, no matter how many tries.
We tried changing the relays around with no luck. We went and eat lunch and back to the truck with a rubber hammer. Then it starts on the second try without using the hammer. We got under it and cleaned the connections up and put some bulb grease on them. I couldn't get the one apart right on top of the pump itself, I was afraid of breaking it. It's been doing fine since we left the church before we cleaned the connections.
View 14 Replies
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
View 14 Replies
Almost every time I start my 2001 Ford Focus, it won't start. The starter functions but the engine won't start. I have to pump it, give it gas, and once it starts, it's perfectly fine, no stalling, no problems after that. That is until I turn the engine off. When I go to start it again, say after doing an errand or two, it may or may not happen again throughout the day, the problem only occurring when I attempt to start it.
View 1 Replies
Its a 2005 awp 1.8t gti with 180K stage 2 apr. When i tune the key to the accessories on position I used to hear the fuel pump priming but now I don't and the car wont start.
View 5 Replies
The cooling fan runs on high as soon as the a/c is turned on, regardless of the engine temp. I have the sensor(6F9Z-19D594-AA) that mounts on top of the accumulator. If i replace the existing sensor, will the refrigerant leak out?
View 10 Replies
I have a 2007 Ford Escape with a passenger side low beam that won't turn on when the headlights are turned on. I have replaced both low beam lights and checked all the fuses. Fuses are ok,none are burned out. My high beams work perfectly as well as my fog lamps. I need any and all advice and information , including any simple wiring diagrams that could be of use . Is it possible that the multi function switch for the turn lights and headlights is the problem?.
View 10 Replies
We are a 2 Escape family. We have an '03 and an '05 - both 4WD and 3.0 V6. My college freshman son purchased the '05 this summer to get to and from his summer job. It has a little over 173K on the clock and it has a power steering leak, so I decided to try to tackle this one.
There is a fairly good video on YouTube on replacement of the power steering pump on an '03 - but apparently on the '05 Ford decided to relocate the pump from under the upper right engine mount to a lower location closer to the front bumper so the video is not of much use in this case.
I have searched the web and this site but cannot find any tips or instructions to replace the power steering pump on the '05. The Chilton Manual I have does not acknowledge the difference in the power steering pump location on the '05 and only provides the procedure for those Escapes where the pump is located under the upper engine mount.
I think I may be able to get better access by removing the inner fender plastic and perhaps the front bumper cover, but would really like to know the accepted procedure before I start tearing into this one.
One interesting bit of info regarding power steering fluid on these vehicles. Ford designed them to use automatic transmission fluid (Mercon) instead of power steering fluid. Initially, when I saw the leak, I thought it was a tranny line leak. Then I traced it to the front of the engine which is totally on the opposite side of the vehicle from the tranny lines.
View 14 Replies
