Ford Escape / Hybrid :: 2001 - Cruise Control Not Working
Jan 31, 2014
The cruise control has not worked on my 2001 escape since i bought it a few weeks back. i checked the usual culprits and everything is good. i plugged my scanner in and got a control module code.
c1945- park switch indicates park with vehicle moving.
I did do some live data testing and it does infact show park when in gear. the display on the dash shows the proper position.
I am almost certain this is the issue with my cruise. Where this sensor is? Doing a parts lookup isn't showing much.
View 11 Replies
Advertisement
I recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.
View 3 Replies
I recently purchased the 2006 Mazda Tribute and the previous owner has confirmed the cruise was not working. What I have looked at:
Checked fuses
checked cable and connections
check connections at unit
What I have is the cruise will power on (light on dash comes on) but it does not appear to engage. I tried to use the diagnostics built into the car, where you hold the off button and turn the key on. I get a flash for off, and on, but do not get a flash when I push the resume button.
View 3 Replies
Looking for any pointers on fixing my cruise control Have looked around under hood but what it looks like. I've got the air working again,put Warn hubs on and have ordered the Hellwig rear sway bar,adjusted steering box i/2 turn....
View 14 Replies
The cruise control in my recently purchased '01 Excursion isn't working. I've done a lot of searches and discovered there was a recall for a wiring harness: 2001 FORD EXCURSION Recalls
I called my local dealer and they stated there aren't any open recalls for this vehicle, so the previous owner must have taken care of it.
Is there any way I can verify that the warranty work was done? Can I visually inspect the harness? What else I can check to fix the cruise control? The lights on the steering wheel are illuminated.
View 14 Replies
I have a cruise control issue. I tried the self diagnostics test, and the "cruise" light would not come on. (Also read that 2001 did not have a self test, so maybe that's why it didn't work? Also, when I first start it, all the other lights turn on except for cruise.) I checked the brake master cylinder and it has the double fuse wiring with 2 good fuses. Not quite sure what else to test. I just bought the X knowing it had this problem, but didn't know how much I would miss cruise control until driving without for a week.
View 12 Replies
One day it work and the next day it didn't. I checked the 15a fuse and it was good. What else should I be looking at?
View 12 Replies
I've just bought 2001 f-250 crew cab and when I push the cruise control on the steering wheel it does nothing. Maybe a fuse or does my year have one of those master cylinder switches?
View 12 Replies
2001 F250 SD 7.3 PSD Was doing a trailer towing road trip too and from Montana. On the way back the cruise control stopped working. Checked fuse #28. Looked fine. Attempted to do a self test on the cruise control. Holding the OFF button did nothing. Never went into diagnostic mode. Button ? A different fuse?
View 14 Replies
My 2008 Escape LTD AT steering wheel has a chunk out of it, so I got a steering wheel off eBay advertised as a '2008 Escape' steering wheel (came with upper part of column also). The color is the same, and it looks exactly the same - except for one cruise control button.
I don't know if there was a difference between the MT and AT cruise controls; the owners manual doesn't say. Or if maybe this wheel is from a different year than 2008. What I would like to know is if the wire connections will be the same, if the 'Set-' button is the same as the 'Cst-' button.
I'd hate to swap them and then find out there was a different pinout for the eBay cruise buttons....
View 2 Replies
I have a 2003 2.7 auto. Quite suddenly the speedo and cruise control have stopped working. Everything else works just fine...
View 2 Replies
I have this weird problem with the cruise control of my 2002 elantra gt: I cannot set the cruise control at 30 or 40 mph, but I can do it somewhere above that (just went to the highway and set it around 60 mph). What could be the problem? Do cruise control systems need calibration or would I have to replace it?
View 2 Replies
My 2002 Santa FE's cruise control has stopped working, light comes on but no hold or anything, any obvious faults they have that I can try. I checked the fuse, that's OK...
View 7 Replies
I was recently on a road trip, using my cruise control extensively (like usual) when it just quit working. I tried to reset to a lower speed, but it would rev itself back up to the original speed. I turned off the cruise control, drove a mile or so and turned it back on. The cruise dash light came on, but the right control buttons no longer worked. No check engine light. It's never worked since.
My local tire shop checked codes and found the tcm not communicating with the mod (cruise module?). I'm looking to take it to the dealer, but I'd like to be better informed with what I may be dealing with before I get there.
View 1 Replies
Never had any issues with it before and was working fine on a trip a couple of weeks ago. On the way home I had it on, we stopped to get some food, and then when we started up again cruise control wouldn't turn on at all. I tried turning on and then setting, but nothing happened so I don't think it's the light. Checked the fuse and it looks fine (no noticeable distortion or break to the wire anyway) and brake lights all work.
View 8 Replies
I have a 2004 Santa Fe GLS that the cruise control just stopped working. It will not turn on when I press the ON button. Could it be a blown fuse? I recently had a new AC compressor installed. Could it be related to that? Maybe something didn't get plugged back in?
View 1 Replies
well Im working on mother in laws 2002 escape...replacing wheel bearing and ball joints...I went with replacing control arm with ball joint already pressed in , I did try to press out old ball joint first but it wasn't budging...so I went on to the control and the back bolt came out fine...except threads at top of bolt look worn bad...anyways moved on to front and it was tight and moving along good...sprayed down with pb blast moved it back in sprayed again and waited a bit....as I went to bring it back out it snapped....I got the broken bolt out...it broke right at where the threads start...anyways Im having problem with gettting the control arm out while the rest of that bolt is still in there.
View 14 Replies
I just bought a 2008 Mercury Mariner about a month ago. A couple of times the Traction Control light came on from when I started it, until I turned it off (5-30 minutes.) Then it didn't come on for days. What the problem could be??
View 1 Replies
Same car I posted about a couple of days ago. It was running fine. My son was driving on the freeway, and tapped the brakes to disengage the cruise control, and the transmission just stopped working. It was not in gear after doing this and the transmission would not engage. It was nothing like a slipping transmission. The engine just revs with no resistance.
Got it towed home and checked the codes: P1529, generic 'Check Engine' light from the TCU; P0760 Transmission solenoid C and P0765 Transmission solenoid D. I have googled these codes individually, but not sure how they tie together.
Oh, I overfilled the transmission. Probably a quart too much because I didn't know how much extra I needed for the torque converter. I doubt this is the issue, but I will drain the excess. Where to check next?
View 3 Replies
After about 6 months I finally got the alternator replaced in the Tribute. I totally forgot about the CEL that was on for EGR Circuit. I've found a couple of pages ( OBD-II Trouble Code: P0403 Exhaust Gas Recirculation Circuit Malfunction ) that explain how to diagnose the issue but I was wondering if any other route for something that may be more common than another thing.
View 2 Replies
So a little while ago I had my parking brake, ABS, and traction control lights all come on at the same time. There was no change in performance, but they have been on ever since. I looked in to it online and a bunch of people said this was a common problem with damaged tone rings, so I checked them out, but they were fine (as far as I could tell anyway). So I scanned the vehicle using a buddy of mine's Snap On scanner, and it came up with the following code:
B1342 Faulty Control Module
We tried to check the fault code through Mitchell OnDemand but it said that this code was for a faulty Parking Assist Module. I don't have any kind of Parking Assist system on this vehicle however. I looked around a little more and this seems to be a pretty generic code for brake system faults with Fords. Also, if the control module for the ABS is the same one that handles traction control?
View 3 Replies
