Ford Brakes/Suspension :: Why Are The Brake Lines Coiled Near Master Cylinder
May 9, 2013
Why the brake lines have 2 or 3 coils in them near the master cylinder? Makes it a real pain to work on anything down in that area. Always snags ratchets and stuff...
My brother and I were discussing it the other nite, and the conclusion we came up with was, the first guy ever who was installing a brake system had tubing that was a couple feet too long, and couldn't find a tubing cutter, so he coiled them up.
Then the next guy saw that and figured "hmm, so THAT'S how it's done", and so on... Kinda like the story about the lady who always cut off both ends of her ham before she put it in the broiler..
View 12 Replies
Advertisement
I have a 79 f150. I changed two brake lines and master cylinder and bleed,and more bleed,but still very soft all most to floor? wheel cylinders look good.
View 2 Replies
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cyclinder need rebuilding or is my vacume diaphragm going. Not sure thats what its called.
View 14 Replies
I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 Replies
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 Replies
Which line goes to front brakes and which to rear from the master cylinder?
View 1 Replies
What kind of brake line is it and if is replicable with regular brake line? I'm just replacing long line between front and back splitter block and just would like to know what is it. What is purpose of that braiding (?) at front brake lines and why they wind down instead of going straight. Part of that long line is braided too, part that go across frame.
View 3 Replies
I have a '53 Ford F100. I have a PB conversion kit on it. The master cylinder & Booster are under the floor. I have used this setup for many years. Recently my master cylinder went bad. I replaced it with the same model. I bench bled it, and installed it. I also added a remote fill kit, since it's difficult to check & fill. Because of the booster, the master cylinder no longer sits under the hatch in the floor.
I got everything installed & connected, then bled all 4 wheels using a bleeder kit with an electric vacuum pump. The fluid runs clear & no bubbles, but I can't get a pedal by pumping. I have no leaks. I tried with the engine off, and running. I have felt soft pedals before, but I have no pedal at all, it just goes to the floor.
View 13 Replies
I was wondering if there was how to on doing the MC replacement? The brake pedal goes to the floor almost every time you press on the brake?
View 1 Replies
Is there a good way to bend brake lines without a bender? I have two brake lines to bend that are probably no longer then 3 feet and don't want to buy a bender.
View 6 Replies
I am having trouble big time getting air out of my brake lines. I put new front pads and rotors on and also had to replace the brake line coming from the caliper as it kind of crumbled and needed to replace the next line up that goes to the ABS block on the left front. After doing this, I bled that wheel only and at first it was ok until the brake line on the right front at the caliper also broke when I was pushing on the brake pedal with the truck running, spewing fluid all over. I have tried to bleed using a decent vacuum bleed setup from Advanced Auto but keep getting massive amounts of air coming out and when I start the truck and hit the brake pedal, it goes to the floor. Could the master cylinder be bad? I have checked every connection that I made and all other connections and there are no leaks at all. I am stuck in the garage! The truck is a 1999 F150 4x4 with 4 wheel ABS.
View 1 Replies
A few years ago I (for him) replaced all 4 calipers, rotors, pads, etc....things were good. Just recently he replaced his Brake Booster and Master Cylinder (not sure what led to this), but long story short everything is back together and he doesn't have brakes.
My GUESS is that the system needs a good flush, new fluid, etc....
My problem is I'm unsure how to bleed the ABS system. A few google searched indicate I need a scan tool, but is there another way? Can I jump something.
So my question, how do I completely bleed the brake system on this truck?
View 7 Replies
I replaced my MC cap and gasket less than a year ago with a Dorman replacement and I'm leaking again, already. I don't want this to be an annual thing! Any good quality replacement? Is there any tip or trick to get the gasket to seal better?
View 9 Replies
Early 70's Ford truck. The brake MC fluid is filled but not overfilled, and doesn't leak at all when the truck is parked. It can sit there for a month and never leak a drop, parked. But when I drive the truck, even just around the block, then park, and look inside the engine compartment immediately the brake MC is dripping brake fluid. It appears the leaking mode is by the fluid somehow jumping up and coming over the top edge of the MC when the truck is in motion or when the brakes are applied. All my diy'er years of replacing brake master cylinders on Ford Galaxies, VW Rabbits, Corollas, and this truck, I've never seen this kind of weird brake problem before. On this MC design it seems there's sort of a rubber baffle inside the lid of the MC, and that's present and accounted for.
View 17 Replies
...Is there anything special that needs to be done for brake bleeding after putting in a new master cylinder? I decided today to flush my system with my vacuum bleeder and now my pedal slowly falls to the floor at a light...No problems in a panic stop or otherwise, just falls to the floor slowly when braking...no leaks, so I'm assuming a master cylinder is an order....
View 14 Replies
I have a 1999 Ford Explorer Sport 4.0 SOHC.
I change the rotor, calipers, and pads on the front end.
When I went to bleed the brakes I got some fluid, then I got none.
I can hear fluid squishing around up near the master cylinder, but none coming to the caliper.
I see a bleeder screw on the master cylinder.
Before the car came to me the person had, had low fluid, but had brakes. Now the pedal just goes all the way to the floor with no effort.
There are no leaks or broken lines anywhere.
View 14 Replies
Lost braking power. Replaced master cylinder. Brakes went soft again. Shop says it is something to do with the ABS Control Unit (?). Took it to dealer who said it is a leaking master cylinder. Back to shop which claims nothing wrong with new master cylinder and it i the ABS blah blah. Dealer says it can't be ABS. Went to another shop. Replaced master cylinder again. Brakes still soft. No one can figure this out and I am stuck with very soft brakes.
View 5 Replies
I tried to replace my brake master cylinder today but wasn't able to because of a plug
It's the black plug on the drivers side, the connector is upside down so I can't see how to unplug it I tried for an hour then got too frustrated I had to come inside
My Haynes manual says "unplug" obviously
View 1 Replies
ll, I changed out the master cylinder on my 2002 F-150, disk brakes front and back w/ ABS. Bleed all the air out and bench bleed the master cylinder. I have good pedal but the brake light will not go out.
View 6 Replies
My son's 2006 F-150 4x4, with 107,000 miles, has in intermittent brake light on. I replaced the rear pads, as they were nearly into the rotors. The brake pedal feels fine in all braking conditions. Could the master cylinder still be going bad? Anything else to check?
View 4 Replies
I have a 2004 Camry LE with 214,000 miles on the clock, and this car has had needed maintenance pertaining to the braking system ever since I bought it in January. Let me give you some background on past issues/maintenance before I dive into my current issue.
During the test drive, the brake pedal felt extremely soft/spongy, having to travel a lot farther than any other car I've driven (even my father's full size pickup had stronger brakes). My dad dismissed it just being the way the car was. In hindsight I would've walked away or slept on it, but let's just say I was pressured into buying the car right away.
We took it to my trusted local mechanic a few days later for an overall inspection, and he said the front brakes/rotors needed to be replaced. He said the rear brakes were thin, but could be replaced later down the line. So we replaced the front ones, expecting it to have some improvement. In reality, the brake pedal force was still the same as before.
A few months later, after hearing faint squeaking coming from the rear brakes, the brake light started to illuminate intermittently. That's when we decided to replace the rear brakes/rotors. After we replaced the rear brakes, braking motion was dramatically improved, and I did not have to push the pedal very far to achieve adequate braking power. It was great,while it lasted.
It gradually started to go back to the way it was, which is really disappointing. After growing tired of the problems, I decided to check the brake fluid level in the reservoir, and it was practically at the minimum line! Figuring it was a brake line or master cylinder leak, we took it again to my mechanic to have him inspect the braking system. Much to everyone's surprise (including my mechanic), there were no leaks to be found and he told me to come back if it gets worse or the brake light comes on. HOWEVER, when I drove it home from the mechanic, the brakes felt the way they did when he put the rear rotors on. On the service record, it said he just looked for leaks and readjusted the rear rotors. This was about a month ago, or at 209,000 miles.
However, as before, the brakes slowly started to loose their "bite" again and sure enough, the master cylinder had lost fluid; albeit not as significant as before, but enough to require topping off. In addition, whenever I'm decelerating on the freeway (from let's say, 75-60 MPH), the wheel shakes as well. This wasn't really present before.
My patience is running thin with this car; we've easily spent half the value of the car on maintenance.
View 12 Replies
