Ford Brakes/Suspension :: Stabilizer / Sway Bar Clamp Part Number
Jun 10, 2016
What are the part numbers for the REAR Sway Bar Bushing Clamp to fit a 2004 F350 Dually w/ the dana 80 axle? This is the part that surrounds holds the bushing that encompasses the sway bar holding it to the axle itself.
Found out couple weeks ago that the front and rear bushings were different heights. Meaning the ones for the front sway bar bushings were taller and the ones in the back were shorter. I can find the part numbers for the front ones pretty easily but the rear ones is like searching for the holy grail. And yes I need the shorter rear ones.
View 1 Replies
Advertisement
I'm wanting to get a single in-line steering stabilizer for my '05 F250 4x4, but I can't seem to find any that include brackets.
I don't need a dual setup because I'm not running a big lift or big tires, but I want an inline stabilizer so that I can just leave the stock one in place.
What is the part number for one that comes with the mounting brackets?
View 7 Replies
Looking to replace the steering stabilizer on my 2008 F-250. It has a 6" lift and 37" tires.
Also, does "dual" mean better?
View 3 Replies
While underneath truck today i noticed the front stabilizer bar has disconnected at both ends,Haven't noticed anything in the handling,How important is this thing ?
View 5 Replies
I need the part number for the lower shock bolt that holds the shock, swaybar link, and trailing arm together. It came loose and stripped the threads out of the trailing arm. I think if I can find a nut the right size I can tighten that against the outside of spindle for a temporary fix. I can't seem to find one, or a part number.
View 2 Replies
I'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 Replies
I am looking to install a new Message Center in my 2003 Excursion XLT. I have checked the vehicle for wiring and everything seems to be in the right places. I have ordered the Ambient Temp Sensor and that will just plug into the harness that is on my vehicle with a factory cap in place at the moment. However when I tried to order the message center, the dealer said it would be best to get the part number off one that is currently in a vehicle.
View 13 Replies
While fixing some trans leaks on my 6.8. I was tightening a clamp on the center cooler and the lines must have rotted. It snapped off. I was having problems with both attachment points. So guess it's just time. Problem is I cant find a good part number to order one. I can't find it on Rock auto. Here is a picture if it. It's between the front and main radiator.
View 10 Replies
Looking to confirm the part number. My ICP is mounted on the RH valve cover and has a yellowish upper where the three pronged connector inserts.
View 10 Replies
When I bought my truck one side of my truck had plastic between the outer sheet metal and inner sheet metal and the other side was missing. It looks like the purpose is to keep mud and road gunk from shooting up into the rear area. Where I can order replacements and what they are called? I need both sides, since the one I did have was cracked and barely hanging on.
View 8 Replies
Had a question about where the battery fuse is located and it's number. I just put a brand new alternator on.my truck. Turns out I might not have needed one, switched the battery with the new alternator on and the truck still went dead after it ran for about 10-12 seconds. So some told me it may be the battery fuse but I don't know which fuse it could be.
View 2 Replies
I am having trouble finding the correct part number for the Ford emblem that goes on the front grill on an 09 F150 lariat crew cab. My father in law asked me to order one since his is faded badly. What is the correct part number?
View 1 Replies
I am swapping to a 6.0 trans cooler in my 7.3 and want to add the external filter as well. I looked through the tech folder and the link about the external filter doesn't seem to be working. I am just looking for part numbers of what everyone is using. Is the Magnafine as good as a spin on style filter?
View 11 Replies
I found 2 Ford OEM part numbers for what seems to be the same identical metal CAC Tube for the drivers side.
6C3Z-6C640-AA
and
6C3Z-6C646-BA
I wanted to place an order today for my '06 but want to make sure it's the right one. What is going on here? (maybe one is for a '03-04) I Don't know...
View 14 Replies
Checking the front end with the front wheels off the ground I noticed that my Suspension Stabilzer Bar has about an 1/8" up and down play in it. No side to side play at all. I checked the nut on the ball joint and it is tight but wondering if this is why I am feeling a slight tight/loose feeling when going down the freeway at 65.
It has this "tight" or a slight grab feeling when the steering wheel is centered and I move it left or right slightly (like normal steering wheel movement to stay in your lane) I don't feel this at slower speeds 30-40 etc just when I am straight on the freeway at about 65-70 mph.
Ball joints and everything else looked fine, no play noticed. Never had the "death wobble" but having this up/down play in their stabilizer bar.
View 4 Replies
With an AD2 and no HFCM, need to have a part number for just the top of engine filter? All I can find (Motorcraft, AMSOIL, Racor) are the dual filter kits.
View 4 Replies
I'm doing standpipes and dummy plugs. There is a 4mm plug with an oring and mine was trashed. What is the P/N?
View 13 Replies
When I went to do my fuel filters tonight I found that the Fuel Return Tube had broken. I have the Ford part number 3c3z-9t289-AA and was looking to see what is the IH part number. I think I'll pick up that oil filter assembly too.
View 4 Replies
What the exact part number is for the seal for the rear axle in a 2003 F150 4x4 ?? Mine decided to leak yesterday and so I looked up Ford for the part but there's two .. one is thick and one is not. I don't want to take the seal out first to look because I got no other vehicle to get it and putting it back in and out would be silly.
View 4 Replies
Does that little clip that grounds the PCM case have a part number? I've been troubleshooting an "SES - but no codes that would cause it" issue, and noticed tonight that clip is not there. Even a photo would work, as I assume I could make one if I had to. It's just a piece of copper, right?
View 4 Replies
I need to remove my EGR valve to clean the unit of carbon. While there I will be removing the intake elbow to check if I have the throttle plate installed on my engine. What the part number is for the gasket / o-ring that seals the elbow to the intake manifold??
View 7 Replies
