Ford Brakes/Suspension :: Front Brakes Are Dragging / Does Not Stop The Truck Just Gets Hot
Apr 11, 2013
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 Replies
Advertisement
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
View 4 Replies
Here's the deal:
* Drive the truck after it's been sitting a while (overnight, or at least a couple of hours), everything's fine. Good brake pedal feel.
* Drive 10-15 miles, stop-and-go at lights and stop signs, the brake pedal slowly goes from normal to firm, to very firm. Then, no play whatsoever and brakes are dragging bad. Yesterday, they were dragging so bad that I had it pulled into 1st gear with pedal on the floor just to get thru an intersection.
* Get out and check each wheel, all 4 brakes are dragging. I can tell from the heat pouring out of each wheel. And I've verified with infrared thermometer. Also, I've raised the vehicle when this is happening, and all 4 wheels will not turn. So it's definitely all 4 brakes.
At first, I assumed it was seized slide pins. But I've THOROUGHLY cleaned each and every one, and lubed with synthetic caliper grease. When the brakes are feeling normal, I've had my wife pump the brakes while I watched the calipers. Near as I can tell, they slide easily. Again, when my problem happens, it's all 4 wheels SIMULTANEOUSLY. So I've pretty much ruled out slide pins.
The brake pedal itself isn't getting bound by anything. It moves freely and I've lubed each of the pivot points. No problems there.
* When the brakes are dragging, I can crack the bleed screws and some fluid will come out at each wheel, which releases the brake at that wheel and I can then turn each wheel freely. So, there's residual pressure in the lines. I replaced the master cylinder (twice actually). No change in behavior.
BTW: I thoroughly bled the lines after each of the two master cylinder changes. I must've put 60+ ounces of fresh/clean/new fluid into the system so this isn't related to old fluid.
* Next, when the brakes are dragging, I can unscrew the master cylinder about 1/8-inch or so from the booster, and the brakes immediately release. Again, indicating residual pressure in the lines. So, I assume that something funky is going on with the brake booster. Also, when the brakes are dragging, I can pull the vacuum hose from the brake booster. And after a few seconds the brakes release. So I installed a new brake booster (re-manufactured one from NAPA -- they didn't offer a brand new one). No change in behavior.
After swapping the brake booster, I can still pull the vacuum tube when the brakes are dragging and it'll release in just a few seconds. So, it really seems like something is going on with the booster, but I can't figure out what it might be.
It is possible for the brake booster vacuum tube to have TOO MUCH vacuum, thereby causing the brakes to be unknowingly applied? Is there maybe a regulating valve of some kind in the line?
View 2 Replies
On a 1998 F150 2 wheel drive 4.6 250k, the front brakes will drag under a specific set of circumstances; only in prolonged stop and go traffic with hot ambient temps. Rotors, calipers, rear shoes, drums, fluid, bearings, seals have all been replaced. This occurs only a couple of times a year, otherwise the brakes work perfectly. It starts out as a slight shimmy that worsens until you can smell the pads cooking and the wheels are hotter than hell. The truck will hardly move at times. The rears are normal. After the truck cools for hours, no symptoms.
View 7 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 Replies
On braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
View 1 Replies
I've changed brakes on tons of front wheel drive cars, and two wheel drive trucks. But NEVER on a 4wheel drive Super Duty. My truck needs new front brakes now!!!! its a 2003 F350 4X4 -58,000 miles. I was just wondering from you all, how hard is it to change brakes on a 4x4 truck? Do I have to remove the Hub or lockouts?
View 5 Replies
Initially when I start driving, the brakes work just find. But it seems as I use the brakes, the front brakes build up pressure and slowly start to lock up. They don't lock up completely, but they do cause a significant amount of drag. The rotor, calipers, rubber hoses and master cylinder are all very new. I'm thinking maybe the issue is with the master cylinder and am considering going to get one along with a brake booster(since it doesn't have one currently).
View 14 Replies
Drove a few miles and both front brakes got hot. The driving was mild failry flat road under 30 mph and the steel rims were hot to the touch around the lugs on both sides pretty evenly.
The van is new to me and I've driven maybe 20 miles so far. The pads are about new, the rotors look fine. Already I've changed all the COPS and plugs, changed the trans oil and filter and installed a drain plug, chaned the engine oil and filter, changed the air filter, and rear drums are on order. So it would be nice to be done soon!
View 1 Replies
I changed over to summer tires today on my 1999 4wd F350 diesel . While the front tires were off of the ground, I tried rotating the wheels by hand to see what the resistance was like. I was surprised at how stiff they were. It would take three fingers to rotate the wheel and as soon as I stopped applying pressure the wheel stopped turning. I pulled the rims off and found that the calipers appeared to be contacting the rotors and causing resistance.
My last rig was a 1960s 4wd F250 that had calipers that could be adjusted manually. I kept these adjusted so the calipers were almost touching the rotors. I could spin the rims with one finger and the wheel would turn for 30 seconds or so until coming to a stop. Is this normal?
View 2 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
1998 FORD E350 CLUB WAGON 15 PASSENGER VAN. Front brakes are sticking bad. Stop at intersection with snow or slick condition and you can barely get the van to start moving. After you do you can fell the drag and the vehicle working hard to keep moving. Take tires off front, can not see anything obvious that is wrong. Can see where the bake pads are leave makes on the rotor.
View 4 Replies
I have a 99 f150 4x4 that has done this twice, once last year and once this year during hot (90+) weather. I'll notice the vehicle seems like it doesn't want to go. Park overnight and it will work ok. Last time it happened the other day I stopped at wally world and both front wheels were real hot and I could smell the brakes. Came out hour later and when I pushed the brake pedal to put it in gear the pedal went to the floor.
Pumped up pedal and drove off but truck would barely move, drove 10 mph to a buddy of mines shop and it sat overnight and worked perfect the next day. He inspected everything and seems to think it might be the abs control unit. He noticed a small amount of fluid had come out of the unit and dripped on the ground. Also no abs light or brake light has ever come on
View 9 Replies
Bought a high mileage 99 f150 4x4 yesterday. In the process of cleaning her up, the water hose hit the disc brakes on the drivers side and it was hotter than a BBQ grill! Ok, immediately I thought this isn't good. Jacked her up and pulled the caliper. Pads were almost gone so replaced them with a new set, went for a drive. Now the damn things were smoking so bad I thought they were gonna catch fire! Sticky caliper , right? Stopped and got one then realized that the passenger side started doing it too.
Another trip for the other caliper and new pads because these were toast. I mean just burnt to hell. Before I started working on the truck again, I checked on here and I'll be darned if I didn't find out that the old brake hoses might be acting like a check valve because of rust and deterioration. Got a set of brakes hoses too. Put everything on this morning and works like a charm.
1999 4.6 XL
Passenger side done
View 1 Replies
2003 Santa Fe 3.6 V6 with ABS
The car sat virtually driven for a year before it was given to me. After 2 weeks of normal driving this past December, the power brakes completely went out. Had to drive the pedal to the floor to stop at even slow speeds. Took the mechanic and they replaced the Master Cylinder and both brake lines.
Shortly thereafter had an unrelated issue with a coilpack gone bad. Replaced coilpack and at that time replaced both sets of brake pads on the rear.
In January, started noticing grinding metal on metal from both front brakes. Took the mechanic and they replaced both calipers, rotors, and pads.
2 weeks or so later, after 10 minutes of driving the front brakes started dragging. The pedal would become extremely hard, and I could notice thew smell of the pads burning. Would have to pull over, put the car in park and pump the brakes to get the calipers to release. This would occur intermittently every few days. Pumping the brakes would always solve the problem.
Over time, the issue became worse, ocurring far more frequently. Around this time I noticed leaving the engine on in park while pumping the brakes would no longer solve the issue. I would have to completely turn the car off and pump the brakes to get them to release.
Started noticing around this same time that the left rear started grinding. The brake pads completely wore down in 3 months time. Too to the mechanic. Replaced caliper, rotor and pads.
Still having the same issue with the brakes dragging. One mechanic thought it could be ABS related and advised me to pull the fuse and the two breakers to diagnose. Still had the same issue, so put the fuse and breakers back in.
No mechanic seems to know what is going on with it, and I'd hate to have to replace all the brakes again as the problem goes untreated. Is it possible that the master cylinder or brake booster could be the issue? It's a brand new master but that doesn't necessarily mean anything, I'm told. Again, I can only get the brakes to release the pressure by pumping the pedal with the engine off.
View 1 Replies
The front brakes on my 2000 Toyota Sienna are dragging occasionally. I have replaced the front calipers (one of them twice), the master cylinder, and the ABS unit (with a junk yard unit). I have also shortened the master cylinder push rod to see if that would make a difference. The brakes still drag occasionally as indicated by the front hubs becoming excessively hot.
View 9 Replies
Truck is 2007 6.0L 4 door F-250 FX4
So this started after some High water encounters around my area. All freshwater. Went to the store and then i notice the truck pulling Left and got home and checked brake temps and the driver front and rear were over 400*F passenger side was 150* or less. No trailer no load in the bed. I decided to clean everything. Pads are worn but still have life.
Rotors showed some signs of where the pad is dragging Not bad though just a small area close to the top hat. I cleaned pads, carriage, and clips and reinstalled everything with some anti seize on the edges of the pads where the clips are and at the same spots on the carriage.
Thought it was ok but the after more water and a day or two sitting the same thing happened again. It is only the drivers side and it's both front and rear. I am stumped on this one. Two calipers going bad at once? I need to tow a boat on Monday So I have got to fix this.
View 1 Replies
I have a 2006 Subaru Forester with 115K miles. It's been well-maintained and well-loved.
For the past few months, the brakes have been inconsistently making a dragging/grinding noise when coming to a stop at low speeds (<5mph). It sounds to be coming from the front half of the car - I can feel it vibrating a little near the driver side. We've taken the car in to be looked at three times - each time, the mechanics think they've heard the noise and report there is absolutely nothing wrong with the brake pads or rotors. Twice they reported a shim was out of alignment. After the last shim adjustment, the noise got a little better - instead of grinding, it's more of a dragging sound now. Because the noise is inconsistent, I haven't been able to crack the formula of the conditions that produce it, other than that it only happens as I'm coming to a stop at very low speeds.
Is there something besides the brakes we should be having inspected? Does this sound safe to drive?
View 10 Replies
Our 2010 Prius just had the brake booster recall done and I also installed new pads and rotors. The car now has issues with the front brakes dragging excessively causing lack of power and poor fuel economy. There are no codes and everything else checks out okay, the brakes function fine. Is there anything on these cars that would cause brake drag after a new brake install? I just want to ensure there isn't something I can do before I bring it to the Toyota dealer.
View 10 Replies
