Ford Brakes/Suspension :: After Pressing Pedal Resistance Became Really Soft And Brakes Very Sensitive
Apr 27, 2012
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 Replies
Advertisement
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 Replies
After putting my Ford Ranger in park and pressing down on the E-break to get the news-paper or mail. I've noticed that there is a consistent squeaking coming from the back drum brakes when the brake pedal is applied. But only for a certain period of time; then the squeaking stops.
View 8 Replies
I changed front rotors and bled brakes. They were hard for a few days and went soft. No leak in fluid (MC reservoir is still full). No leak in fluid near any wheel. Could I need to bench bleed the master cylinder?
View 12 Replies
I have a 79 f150. I changed two brake lines and master cylinder and bleed,and more bleed,but still very soft all most to floor? wheel cylinders look good.
View 2 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
I just joined as I bought my '97 F-150 5.4 4X4 about 3 months ago. The dealer gave me a 6 month warranty but hasn't honored it at all and I've had one problem after another. That's another story though but right now I'm just trying to fix the important issues. The problem at hand are my brakes.
I was noticing a couple days ago (maybe I never noticed it that much as it was a new vehicle to me) that when I apply the brakes it sounds like a bicycle pump and the pedal travels nearly all the way down. It doesn't hit the firewall but I'd probably guess it has 3 more inches or less until it bottoms out. The hissing only occurs as the pedal travels and stops when the brake pedal isn't moving.
Now I'm not sure if the hissing sound is normal as I replaced the brake booster (from the junkyard though) and the new one still hisses when I apply brakes. The brakes seem to work okay, could be more sensitive it's just the pedal feels soft until it almost bottoms out like I stated before and the the brakes grab a little bit harder. What could it be?
View 2 Replies
The pedal used to go right down to the floor and would barely stop the car from a crawl, in response I have bled the brake lines to all calipers, and checked the hydro booster fluid level, and with only slight improvement the pedal almost hits the floor.
I am thinking the brake master cylinder is shot. The pedal becomes solid after about 15 pumps when off, and holds pressure, when on it takes several pumps to build any sort of pressure and cannot be built up to the solid point, and looses pressure quickly when just holding the pedal down.
View 3 Replies
I have a Hyundai Santa Fe 2005 2.7L 4WD ABS.
The problem is that the Brakes pedal is so soft, that it goes to the floor, and doesn't brake at all in first pedaling. I am able to apply brakes after pumping the pedal thrice in continuation and then when it builds up some pressure, then it brakes and I'm able to stop the car. Once, I take the foot out of the pedal, it goes bad again. Once, again if I have to apply brakes, I have to do 3-4 times pedaling.
The brakes are stopping the car fine when they get applied in 3rd or 4th pedaling and when pressure is built up. Its the pressure not getting built up or maintained in the first go.
What has been done by the mechanics to solve this:
1. Master Cylinder has been replaced with a new one. (This has been done twice)
2. Brake Pads have been changed.
3. Brake fluid has been replaced and is upto the brim in cylinder reservoir.
View 7 Replies
My 2003 Elantra has multi spark (quad) electrodes? I have a hesitation on acceleration problem. Also feel resistance when pressing the gas pedal. I am going to change the plugs and wires. Just wondering if the type of plugs may contribute to the problem.
View 9 Replies
My dad is having problems with his truck, brake pedal goes all the way to the floor even after bleeding all the brakes and the master cylinder. The wheel cylinder didn't have clips in it and he fixed it and it hasnt changed. What do we do? Its a 1993 f150 4.9l.....
View 4 Replies
I did a complete rebuild of my brake system in April. Drums, shoes, wheel cylinders, springs, hoses, pads, rotors, calipers, master cylinder, proportioner valve and flushed all the lines and refilled with synthetic fluid. I have made five trips from Southern California to Idaho hauling home furnishings, one trip to Oregon and one trip to Northern California since overhauling the brakes with everything working great. Now something strange is happening. The brake pedal goes to the floor with very little resistance. It isn't spongy like there is air in the lines. It just goes to the floor if you push it all the way down.
The truck stops ok but it is really scary with the pedal going down like that. You can feel when the rear brakes come on because there is a little resistance in the pedal when they come on. You can actually lock the rear brakes up and skid the rear tires. If you push the pedal down further the front brakes start coming on and if you push all the way to the floor the truck will nosedive and you will get planted in the windshield.
I wonder if the aftermarket Bronco Graveyard proportioner valve is blowing all the pressure to the rear wheels because it won't do it if you take the vacuum off of the vacuum booster. You have full pedal when the booster is deactivated and all the wheels operate normally with the exception of having to plant both feet on the pedal to stop it.
View 14 Replies
yesterday i gave the 02 diesel a treat, 3 new calipers 4 new rotors, and semimetalic pads. the reason for only 3 calipers is the driver side was just replaced 2 months ago after it locked the wheel up on me. both rears were seized so i only had front brakes, and the passenger side front was leaking.
anyway, all new parts and the pedal is fantastic, besides the truck stopping again. this afternoon on the way home from the shop i stopped at a red light. breaks are rock solid. then all of a sudden, the pedal slowly sinks to the floor. but the brakes still hold. i get home and test them. again, pedal slowly sinks to the floor, but they hold. i am thinking still some air in the system, and park hte truck, with the intention of bleeding them again tomorrow.
i get out and see fluid all over the driveway. great. something in the front of the axle is leaking. the frame is drenched. whatever it is, is in front of the frame, on the engine side. what is in there, the ABS unit?
View 3 Replies
I recently purchased a mutt of truck, a 97' F150 heritage w/5.4 Triton motor, 1/2 ton 2WD short bed.
Having a brake issue, the pedal keeps fading. I noticed it first while sitting in traffic on a down hill grade. I am holding the pedal and notice it starts to creep down slowly, I pump it up and it firms up then starts collapsing again. So general logic says hydraulics are loosing pressure right?....No leaks anywhere, so it must MC tight?
I have replaced the master cylinder, brake booster, and both rear wheel cylinders. Long story short they all needed it, truck has 265K+ on the body with 95K on the motor. The only thing I did not do by standard is bleed the MC on the bench, I installed and long bled starting with the right rear working my from longest distance to shortest (wheel speaking). So when bleeding I did of course get air coming out because of the new parts but I still have the same fade issue.
I am confident there is no air in the lines, I have bleed a quart of brake fluid through just to be sure. I have read a lot about proportioning valves and ABS stuff.
I will try and get some vehicle specific photos and attach have hit a road block with this. I am leaning towards the ABS valve thingy mounted on the drivers fender that has four lines attached (2 in and 2 out). Other than that it comes down to hard lines which have no leaks.
View 5 Replies
My buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 Replies
My problem, Brakes. I hardly have any at all (pedal all the way to the floor and hardly stop), yet the front pads are dragging, and heating the rotors. Maybe a bent line? I bled the fronts, and as soon as I loosened the bleeder nipple, a good bit of fluid came out, without pressing the pedal of course. It's dark out now or I would inspect for bent lines. Could there maybe a problem with the booster?
View 6 Replies
I have a '53 Ford F100. I have a PB conversion kit on it. The master cylinder & Booster are under the floor. I have used this setup for many years. Recently my master cylinder went bad. I replaced it with the same model. I bench bled it, and installed it. I also added a remote fill kit, since it's difficult to check & fill. Because of the booster, the master cylinder no longer sits under the hatch in the floor.
I got everything installed & connected, then bled all 4 wheels using a bleeder kit with an electric vacuum pump. The fluid runs clear & no bubbles, but I can't get a pedal by pumping. I have no leaks. I tried with the engine off, and running. I have felt soft pedals before, but I have no pedal at all, it just goes to the floor.
View 13 Replies
I am working on a e-150 van, 2005. the brake pedal fades to almost the floor with little pressure on it. I just replaced the master cylinder, bled the entire system, and it STILL fades to the floor. driving, or in park. engine running. 4 wheel disc, 4 wheel abs...
View 5 Replies
86 f150 4x4
brake pedel goes straight to the floor but if u give it short pumps of the pedel it grabs but barley....master cylinder or the booster?
View 9 Replies
