I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 RepliesI have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems i was having the the speedometer and the transmission not shifting correctly.
Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles? Had to push the truck hard to get it back to my house, a mile or so. If i let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on.
It was not on before but i am pretty sure the ABS is disabled on the truck. the wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
I'm not too familiar with these trucks, but I've been working on my buddies 1999 e350 ford van.
The other day we were going out kayaking, and the brakes locked up, we were able to drive it home, but it was obvious the brakes were holding the truck back. decided to check it out today, found one front and one rear caliper were sticking, the dual piston calipers only had one working, which I believed to be causing the pads to get pressed together crooked, and caused them to "lock up" or get stuck.
anyways, got the new calipers on and no more sticking, so I bled the brakes started in the front and went all the way to the back, did every caliper. brakes feel firm with the vehicle off, but instantly when the van is started, the pedal goes to the floor. it still stops okay, but the pedal feel is not nearly where it should be.
I got all of the air out of the system, but the abs light is on, and has been for a while. I'm wondering if there is something else that needs to be bled in the abs? someone was telling me about bleeding the abs motor?
I have been having hub locking trouble and finally located a bad vacuum hose. Hose has been replaced. Now when I engage the 4WD and apply a little power, I get a terrible bang out of the front end, then the truck moves on. Sometimes there is a second bang, sometimes not. The chain appears tight in the transfer case and the ujoints look ok. I have turned the wheels with hubs locked one at a time and the joints are free.
View 9 Replies2008 F-350 wheel will lock for no reason. I think the Hydroboost has a hair line crack it and when the temp and pressure reach a certain number then it sends brake fluid threw the crack to the caliper? I also heard it could be in the ABS because its locking just one wheel?
View 1 RepliesI have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 RepliesIf this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 RepliesBrake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 RepliesBefore I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 RepliesOn braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 RepliesI've changed brakes on tons of front wheel drive cars, and two wheel drive trucks. But NEVER on a 4wheel drive Super Duty. My truck needs new front brakes now!!!! its a 2003 F350 4X4 -58,000 miles. I was just wondering from you all, how hard is it to change brakes on a 4x4 truck? Do I have to remove the Hub or lockouts?
View 5 RepliesInitially when I start driving, the brakes work just find. But it seems as I use the brakes, the front brakes build up pressure and slowly start to lock up. They don't lock up completely, but they do cause a significant amount of drag. The rotor, calipers, rubber hoses and master cylinder are all very new. I'm thinking maybe the issue is with the master cylinder and am considering going to get one along with a brake booster(since it doesn't have one currently).
View 14 RepliesDrove a few miles and both front brakes got hot. The driving was mild failry flat road under 30 mph and the steel rims were hot to the touch around the lugs on both sides pretty evenly.
The van is new to me and I've driven maybe 20 miles so far. The pads are about new, the rotors look fine. Already I've changed all the COPS and plugs, changed the trans oil and filter and installed a drain plug, chaned the engine oil and filter, changed the air filter, and rear drums are on order. So it would be nice to be done soon!
My 2003 F-250 5.4L 2WD has a front end vibration that starts around 40MPH (sometimes) and gets gradually worse until it goes away at 55 MPH. It oscillates the wheel a good 3/4"-1". It also does it also when decelerating through those speeds. It "feels" like the left side, but I can't be sure. When I jacked it up, I could get some movement laterally on the left wheel, but not the right. Also Noticed that the drive shaft has about 1/4" of play at the carrier bearing. Leaning towards ball joints.
View 2 RepliesI have a 2005 F250 Power stroke w/ brake controller installed. There is no voltage to the trailer brake (blue wire) pin. I've checked all of the fuses and they appear to be okay.
View 5 RepliesHave 2005 excursion. Just did ball joints , wheel bearings all of them, axle joints and seals.Also warn manual hubs. Have a intermittent scraping grinding noise sounds like driver but could be both front.4wd works fine in high or low, no vibration just this annoying noise. took brakes apart and no funny wear or foreign object in dust shield.
View 3 RepliesI have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.