Ford Brakes/Suspension :: 2002 - Brakes Pull To Left Always?
Feb 17, 2012
This is on my 2002 Ford Excursion 4x4. I have replaced the brakes 2 times with the same results.
New: rotors, pads, calipers and grease the caliper slide pins so they are sliding properly. I have also replaced the slide pins the first time. I even lightly greased the ends of the brake pad back plates where they mount in the calipers/brake clips. There is always more brake dust on the left front wheel compared to the right front. The steering wheel turns to the left when I hit the brakes. I can't figure this out.
The one thing that seems strange is it was very difficult to get the pads and brake pad clips into the caliper. It almost seems like the pads are too tight into the clips/caliper. I am wondering if taking a little material off the ends of the brake pad back plate to allow better movement in the caliper/clips.
The left front is either grabbing too much or the right front is not grabbing enough.
View 14 Replies
Advertisement
1996 F350 PSD 7.3
Front Dana 60 mono beam
4 x 4
Last week I broke my front right caliper. I replaced the caliper, rotor and pads. Now, when I apply the brakes I pull to the left. I took the truck into my repair shop and let them figure it out. They were unable to repair the truck. They replace the master cylinder, all brake lines, calipers on both sides, brake pads, bearings on both wheels, vehicle alignment, tire balancing and tire rotation. The tires are three months old. Prior to last week i did not have any problems braking or steering. Driving at 60kmh the truck goes straight until i gently brake, it will slightly pull left.
View 2 Replies
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 Replies
Im wanting to delete my abs brake system in my f150 2002 2wd all disc brakes.
I have to change the module with some kinda valve? and turn off the Abs in a tune?
I know the basics of a brake system, but im lost in the abs stuff.
View 6 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
View 10 Replies
Just did the rear brakes on my 05 EX. New rotors and pads. Now there is a squeal when going around a left turn. It is a constant squeal when going around a left turn, not a squeak-squeak-squeak. Sounds like it is coming from the left rear. Took it back apart to make sure I didnt miss anything and everything looks fine.
View 1 Replies
Just replaced break pads and rotors. Inner pad on left side was gone leading me to believe slides were not working properly. Pulled apart, cleaned and greased everything, and replaced pads and rotors. Calipers seem to be working fine. Now when I break hard, the truck pulls badly to the left. When I break softly, it seeks normal. My front end is a bit out of whack and veers just a bit to the left. Do you think this is my issue with the breaking ? I'm getting new tires and an alignment soon but was just curious.
View 3 Replies
My 97F250, 7.3 diesel, 4WD has an intermittent steering issue. When I come out of a turn, it doesn't want to come out of the turn all the way. It will keep pulling one way, and I have to jerk the steering wheel in opposite direction, and sometimes the truck then over corrects quickly the other direction. Mechanic said front end looks good, so he replace the power steering pump. That didn't work...
View 4 Replies
Two months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 Replies
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 Replies
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
View 14 Replies
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
View 4 Replies
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
Yesterday while driving, i lost all power steering and power brakes (you would automatically think Booster). I pulled over, popped the hood and fluid was spewing from behind the power steering pump somewhere. I limped the truck home about 20 miles. I checked brake fluid and it was full. checked power steering fluid and it appeared to be empty. Yet when i added fluid it took less than a half quart. I started the vehicle to pressurize the pump and find the leak. Yet the pump never pumped any fluid. (one would thing pump was out) I am baffled as to if the pump went out, why fluid loss? If the booster was out, why do i still have brakes just without power assist? Andif a hose is blown, why such small fluid loss? I dont want to just start replacing parts till it get the right one
View 1 Replies
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 Replies
Brake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 Replies
On braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
View 1 Replies
