Ford Brakes/Suspension :: 1997 - Howling Noise / Rear Tires Started Locking Up When Turned
Mar 28, 2016
I've got a 1997 Ford Expedition 5.4 with 200,000. So my rear differential leaks a few drops of fluid every time I drive it, looks like it's coming from the pinion seal. I've just been filling it topping it off with fluid.
Anyway, yesterday I got in it and started driving, I noticed a howling noise, and when I turned my rear tires started locking up. It was like that for about 5 miles until I got home, no matter which way you turned the tires would lock up.
I went under and topped off the differential with fluid again, and I pushed my parking brake in and released it. Got back in the truck and drove, and it was fine. What happened? I'm just worried it will happen again if I don't look more into it.
View 2 Replies
Advertisement
I have a 2004 Ranger 4x4, 4.0, auto and have trouble with the back brakes howling, locking up and generally driving me nuts. I've replaced the drums, shoes, cylinders, emergency brake cables and all the hardware. We've bled all 4 numerous times, blown out the lines, looked for leaks and done all we can think of. What am I missing?
View 1 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 Replies
I'm having a problem with my rear drum brakes locking up when I press the brake pedal. I've had this problem before, but ignored it because it wasn't too bad. It would just release after taking my foot off the brake pedal.
1998 F-150 XLT supercab 4x4 front discs, rear drums 4.6L v8 175k miles
I cleaned my master cylinder and bled all brake lines so they have fresh fluid. Now that my brakes work way better, my rears just lock up. I put new brake cylinders on, still locking up. I went to a junkyard today and replaced the proportional check valve, brakes still locking up.
Could I maybe have did something wrong when cleaning the master cylinder? I'm sure I put it back together correctly. Anything else i should look at? bad lines maybe?
View 14 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
I have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems i was having the the speedometer and the transmission not shifting correctly.
Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles? Had to push the truck hard to get it back to my house, a mile or so. If i let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on.
It was not on before but i am pretty sure the ABS is disabled on the truck. the wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
View 1 Replies
On braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
View 1 Replies
Last weekend I did a rear brake job on my 1997 F350 4wd diesel. I replaced the shoes, replaced all the hardware, replaced the cylinders and had the drums turned. I have driven the truck all week and everything has been fine. Tonight while out of town I set the parking brake to see if it was any better since the rebuild, and it was. Shortly after releasing the parking brake I drove about an hour to get home. When I arrived home by driver side rear brake, wheel, etc. was very hot. I threw water on it and it turned to steam instantly.
I suspect that setting my parking braked hard like I did (like you're suppose to) somehow caused it to drag. What is causing this and what needs to be done so that it doesn't happen again?
After reading some other posts I went out and checked my parking brake cable and found that it is not bound up that I can tell. Perhaps it did not completely release although it seems to release just like the other side. I checked it from front to equalizing bar and it is in great shape. The plastic coating is still on the wire and there isn't any corrosion the entire length. The only thing I did differently on this trip vs the one I made two days ago was try out the parking brake before I left. The last trip I could barely feel any heat on the rear wheels when I got home, this time the driver side was scorching hot.
View 1 Replies
I have A 97 F-150 4X4 with rear drums. I noticed the brakes felt like they weren't releasing right away after i let of the brake pedal. i took drums off and noticed on the left rear the front shoe moved normal but the rear shoe didn't move at all. on the right side front shoe moves normal rear shoe very very slow, and i could see rear shoe was worn way more than front. So I replaced on both rear the shoes, all the hardware, springs, wheel cylinders and brake line from cylinders to the proportioning valve.bleed the brakes, and adjusted the drag on the drums. Now i drive it, test it out, feels like the same issue is going on. feels like im driving with the brake on, and right rear gets really hot. Did i miss something? not do something right?
View 4 Replies
Recently purchased my first Ford truck, a 97 F250 w/7.3L diesel. I discovered the passenger rear drum brake was full of oil. Cleaned it up and put it back together to do some research.
I see how the hub comes off and there are two bearings in it an an oil seal. The bearings are lubed in wheel bearing grease. Does differential oil circulate through the bearings too?
It doesn't look like a difficult job. Do the seals go bad often or could this be due to a clogged differential vent? Truck has only 100k miles. Any gotchas I should be aware of?
View 6 Replies
I have had my 2011 model III for a month, and today I had to brake rather abruptly. I heard my tires squeal! Is this normal? I have owned at least two other vehicles with ABS, and I recall the pulsing of the pedal, but not tire squeal.
View 3 Replies
I have been having hub locking trouble and finally located a bad vacuum hose. Hose has been replaced. Now when I engage the 4WD and apply a little power, I get a terrible bang out of the front end, then the truck moves on. Sometimes there is a second bang, sometimes not. The chain appears tight in the transfer case and the ujoints look ok. I have turned the wheels with hubs locked one at a time and the joints are free.
View 9 Replies
AC compressor clutch bearings went bad (went AWAY, actually) and the serp. belt snapped. New clutch went on just fine and works great, but after about 20 miles the power steering pump pulley cracked and started spinning on the shaft and the new serp belt jumped half off and ate itself.
So last night I finished putting in a new pump and pulley. Flushed out the lines with new fluid, manually bled the new pump and then followed the bleeding procedure in Haynes carefully. All looks good. Pump spins freely and runs very quiet. No noise or hesitation lock-to-lock. No leaks. Fluid level holds steady right at the half-way mark on the reservoir.
Sitting in my yard it turns smooth and very easy all the way through the whole range.
BUT, out on the street I'm getting very frequent but random lock-up where the wheel doesn't want to turn AT ALL (I'm a big guy and it's HARD to turn)! And then I'll jiggle it a bit and it's smooth as silk again. It's done it while moving fast, moving slow, and standing still. I drove about 30 miles testing it out and it seems completely random when it will lock up, but it did it about six times in half an hour. And when I got home and parked? Perfect, smooth steering.
What could be doing this? Prior to the troubles last week, steering was perfect, so I don't think the steering box is bad. (Could be, of course...).
View 4 Replies
I have a rough chatter noise coming from the rear end. It happens when starting off up till about 25mph. It rattles the cab a little and sounds real rough. It also happens when turning up hill, causes lots of vibrations in the cab. Some have mentioned it could be the rear differential needing a friction modifier or the u-joints needs some special lube? Its an 05 F150 with 62K miles.
View 3 Replies
2008 F-350 wheel will lock for no reason. I think the Hydroboost has a hair line crack it and when the temp and pressure reach a certain number then it sends brake fluid threw the crack to the caliper? I also heard it could be in the ABS because its locking just one wheel?
View 1 Replies
So my saga continues with my rear brakes on my 99 Suburban - had a glazing problem that was eventually discovered, glaze knocked off old pads and then glaze came back again. So we replaced the rear drums and pads. A month and a half later I get an irritating squeaking noise.
Noise - when the tires are rotating they make a light squeaking noise, a rotating/pulsing squeak; when the brakes are applied they make a lower pitch squeak and if I apply just the right pressure on the brakes I can get the noise to go away (while also giving it gas to keep moving).
Last night I inspected the rear brakes and found an excessive amount of dust/grime on the pads. The drums we fairly clean. The pads had a heavy layer of rust/grime on them. When I ran my finger over them it left no mark on the pad because it was so heavy, but my finger had this sooty grime on it. The rust covered about a 1/3 to 1/2 of the pads (each pad had a different amount of coverage).
Everything is brand new and I'm not sure what is causing all the dust coverage.
View 3 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
Two months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 Replies
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 Replies
Drove a few miles and both front brakes got hot. The driving was mild failry flat road under 30 mph and the steel rims were hot to the touch around the lugs on both sides pretty evenly.
The van is new to me and I've driven maybe 20 miles so far. The pads are about new, the rotors look fine. Already I've changed all the COPS and plugs, changed the trans oil and filter and installed a drain plug, chaned the engine oil and filter, changed the air filter, and rear drums are on order. So it would be nice to be done soon!
View 1 Replies
