Ford Brakes/Suspension :: 1997 E350 2wd - Both Front Brakes Getting Hot
Jun 2, 2012
Drove a few miles and both front brakes got hot. The driving was mild failry flat road under 30 mph and the steel rims were hot to the touch around the lugs on both sides pretty evenly.
The van is new to me and I've driven maybe 20 miles so far. The pads are about new, the rotors look fine. Already I've changed all the COPS and plugs, changed the trans oil and filter and installed a drain plug, chaned the engine oil and filter, changed the air filter, and rear drums are on order. So it would be nice to be done soon!
View 1 Replies
Advertisement
I have a '99 E350 passenger van I have been trying to figure out a vibration problem. All the way up to 67 mph it is as smooth as a Lincoln, but from there up a vibration emerges from where I think is the front driver side area. I have done new rotors/calipers, because it needed them, balanced tires numerous times, have put the fronts in the rear and those have not fixed the vibration. The van has 100k on it and I love owning it especially with the big V10. The vibration is just enough to be annoying and when driving it is almost like it cycles for 4 seconds for the vibration then smooth for 6 seconds.
View 3 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 Replies
On braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
View 1 Replies
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 Replies
I've changed brakes on tons of front wheel drive cars, and two wheel drive trucks. But NEVER on a 4wheel drive Super Duty. My truck needs new front brakes now!!!! its a 2003 F350 4X4 -58,000 miles. I was just wondering from you all, how hard is it to change brakes on a 4x4 truck? Do I have to remove the Hub or lockouts?
View 5 Replies
Initially when I start driving, the brakes work just find. But it seems as I use the brakes, the front brakes build up pressure and slowly start to lock up. They don't lock up completely, but they do cause a significant amount of drag. The rotor, calipers, rubber hoses and master cylinder are all very new. I'm thinking maybe the issue is with the master cylinder and am considering going to get one along with a brake booster(since it doesn't have one currently).
View 14 Replies
I have a '99 E350 van that I am feeling a light anti-lock brake pulse in the pedal when I am rolling to a slow stop under light braking. Braking doesn't seem to be affected, but it doesn't feel right. I tried locking up the brakes and didn't feel any anti-lock pulse...seems backwards.
View 1 Replies
I have a 1997 F250 Light Duty with a 5.4L and 4 wheel drive, 216,000 miles. Last year one of my front tire chains broke and ripped the ABS wire. I have soldered them back together and no longer have the ABS light illuminated in the dash. However, when I apply the brakes at speeds slower than 25 mph, the ABS pulses. Over 25 mph the brakes work as they should until almost stopped and then they pulse.
View 1 Replies
Two months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 Replies
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 Replies
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
View 14 Replies
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
View 4 Replies
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 Replies
1996 F350 PSD 7.3
Front Dana 60 mono beam
4 x 4
Last week I broke my front right caliper. I replaced the caliper, rotor and pads. Now, when I apply the brakes I pull to the left. I took the truck into my repair shop and let them figure it out. They were unable to repair the truck. They replace the master cylinder, all brake lines, calipers on both sides, brake pads, bearings on both wheels, vehicle alignment, tire balancing and tire rotation. The tires are three months old. Prior to last week i did not have any problems braking or steering. Driving at 60kmh the truck goes straight until i gently brake, it will slightly pull left.
View 2 Replies
Yesterday while driving, i lost all power steering and power brakes (you would automatically think Booster). I pulled over, popped the hood and fluid was spewing from behind the power steering pump somewhere. I limped the truck home about 20 miles. I checked brake fluid and it was full. checked power steering fluid and it appeared to be empty. Yet when i added fluid it took less than a half quart. I started the vehicle to pressurize the pump and find the leak. Yet the pump never pumped any fluid. (one would thing pump was out) I am baffled as to if the pump went out, why fluid loss? If the booster was out, why do i still have brakes just without power assist? Andif a hose is blown, why such small fluid loss? I dont want to just start replacing parts till it get the right one
View 1 Replies
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 Replies
