Ford Brakes/Suspension :: 1995 F250 Truck Does Not Stop Fast Enough When Hit The Brakes
Jun 18, 2017
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
View 4 Replies
Advertisement
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 Replies
I just replaced the front break pads. I didn't replace the rotors or get them machined, didn't look like they needed them. Once I pushed on the brakes (truck off) I noticed that brake fluid spilled out the brake reservoir. I'm guessing it happened when I compressed the piston into the caliper? I took some of the fluid out of the reservoir and now its at MAX (I didn't bleed them). I've only been only be able to stop and go on the driveway (I'm waiting on a new radius arm bracket). The brakes seems spongy, the brake hits the floor. ABS and Brake lights came on then turned off once I started to pump them when I turned the truck 'on'. Do I just need to actually drive and "break" the breaks in?
View 2 Replies
My problem, Brakes. I hardly have any at all (pedal all the way to the floor and hardly stop), yet the front pads are dragging, and heating the rotors. Maybe a bent line? I bled the fronts, and as soon as I loosened the bleeder nipple, a good bit of fluid came out, without pressing the pedal of course. It's dark out now or I would inspect for bent lines. Could there maybe a problem with the booster?
View 6 Replies
The brakes on 95 toyota tocoma are soft and almost hit the floor and wont stop the truck, My first thought was the master cylinder was going bad so we changed it and bleed all the lines and back with the same problems. I am leaning to a bad caliper but every thing looks good so far no leaks every moves good as far as I can tell. Truck has 200 plus on her pads seem to be in good shape, just don't want to pay a shop and no i can do it myself if i no what part to change and don't want to throw parts at it as I've already did with the master cylinder...
View 18 Replies
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
View 14 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 Replies
Brake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 Replies
I have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems i was having the the speedometer and the transmission not shifting correctly.
Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles? Had to push the truck hard to get it back to my house, a mile or so. If i let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on.
It was not on before but i am pretty sure the ABS is disabled on the truck. the wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
View 1 Replies
Before I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
View 1 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
My truck is a 2004 F350 6.0 as with most of the ford diesels from this era it has hydro boot brakes.
Under normal braking the truck felt fine and the brakes behaved as they always have. However if you where to depress the brakes hard, as if making an emergency stop, the brakes would not lock up in the way they did when I bought the truck two years and 80,000km ago. The problem was slow to appear and at first I blamed it on the larger tiers I was running (stock 2012 F350 wheels and tires (yes the offset is wrong)) but after switching back to my stock wheels for the winter I knew that something was not right. It was something I could live with, it did not make the tuck unsafe it was just that it did not stop as well as I knew it could and this avowed me. I replaced the front and rear calipers and when that had no effect I swapped out the master cylinder this still made little difference.
I drove the company truck all of last month (2008 GMC 2500 Duramax) and when I got back in mine I realised that I had to chase down the problem. I did a lot of reading online and after thoroughly flushing and bleeding my brake system I narrowed my problem down to either the hydro booster or the power steering pump. The plan we came up with for diagnosing was:
1. Thoroughly inspect for PS/Hydro boost and brake fluid leaks following the procedure found here Hydro-Boost Power Assist Systems: Operation Diagnosis and Repair
1a. Consider bleeding the brakes as a bit of trapped air would cause your symptoms.
1.b Consider flushing the PS system. Some suggest this works with tough steering.
2. Have a shop check the PS pressure is within spec. (assuming this is cheaper than buying the tool or just replacing the pump) If it is low, replace the PS pump.
3. If PS pump is fine, or is replaced and the problem is still there, consider replacing the Hydro booster.
It is not super complete but it was a place to start. We checked for leaks and found nothing. The pedal would not sink under braking but would say firm meaning the brake system was free of leaks.
I began a rudimentary test of power steering pump. With the truck in the drive way I could easily turn the steering wheel however, applying the breaks about half way would make turning the wheel imposable. This led me to believe the power steering pump was starting to go. The next step would be to have the pump tested using a power steering pressure gage or take the truck to a shop to have it tested. I found the pressure gage to be more expensive then the new pump so went that way. With 350,000km on the truck I figured it was not a bad thing to do even if it turned out to not be the cause of the problem.
It is a bit tricky to get the power steering pump out but after pulling the radiator line under the truck I could drop the pump out the bottom. The new pump went back in the same way and after a full flush and bleed of the system it was time for a test. What a difference! The truck stops like the day I got it. If your symptoms are like mine I would recommend you check the power steering pump. If it is the problem it is a lot cheaper then replacing a master cylinder or calipers.
View 4 Replies
I have a 2005 Honda Civic with approximately 140K miles on it. When I am going 60+ miles an hour and try to brake, the brakes shake. Or at least that is the best way I can describe it. It makes it hard to stop well when going fast, I have to release the brake and kind of pump them until the shaking is under control. What causes this? and what needs to be fixed? I wonder if it is the way I drive or just a normal occurrence?
View 5 Replies
My 95 F150 2WD. The passenger side wheel is leaning in(top) - toed in? and I am A. concerned that this is unsafe to drive it and B. What is the most likely cause and fix? I was just looking for a starting point.
View 2 Replies
Two months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 Replies
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 Replies
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 Replies
