Ford Brakes/Suspension :: 1994 - Shimmy With ABS On?
Nov 4, 2011
Have read through alot of the threads and can't seem to find an answer. Bought a used 94 explorer xlt. It came with brand new Wrangler tires. The day we bought it we were driving home and it started shaking and wobbling at about 95kms and but seemed to improve after 115. So I took it to the tire shop next day and had all 4 tires rebalanced. The shop told me that all were out to lunch. The worst was 2 ounces out. Ok cool. Was certain that was the problem. Took off. Got on the highway and same damn thing. The steering seems very tight. No bangs. No knocks. Just the bloody shaking. Oh and also the abs light comes on just as it starts to shake.
View 1 Replies
Advertisement
Truck is an 89 single cab, single rear wheel F350 4x4 with 7.3 non turbo diesel and a c6 trans. not lifted, stock size tires. If you hit just the right bump, regardless of speed, the front end just goes crazy.. tires and wheel shoot violently side to side and its very frightening/dangerous. you can just barely hold the wheel, front end is bouncing and whole truck shakes from such rapid camber change as the contact patch swaps from inside to outside of the tread.
Tie rod end, draglink, steering stabilizer (add on,) shock absorbers (rancho,) and a wheel bearing are all brand new. With each part replaced the shake felt worse (since more of it was transmitted to the steering wheel rather than lost in the sloppy parts) and i took it off the road immediately.
Brand new steering box, put it back on the road, did it again less than a mile away. It rained all day so i haven't jacked the truck up again and really, I am quite sick of this problem.
View 7 Replies
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
View 14 Replies
I have a 1994 Black Ford F150 and i was wondering if i could lift the truck 6 inches only using lift blocks (or any other cheap way to get my truck off the ground)....
View 2 Replies
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
View 1 Replies
My 2000 excursion (94K) front end shimmies when I put on the brakes...could my rotors be warped...or is there something worn in the front end?
View 11 Replies
Brakes shimmy on my 05 f150. Been doing this since new new pads and rotors and alignment. what now?
View 5 Replies
Two months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 Replies
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 Replies
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
View 4 Replies
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
1996 F350 PSD 7.3
Front Dana 60 mono beam
4 x 4
Last week I broke my front right caliper. I replaced the caliper, rotor and pads. Now, when I apply the brakes I pull to the left. I took the truck into my repair shop and let them figure it out. They were unable to repair the truck. They replace the master cylinder, all brake lines, calipers on both sides, brake pads, bearings on both wheels, vehicle alignment, tire balancing and tire rotation. The tires are three months old. Prior to last week i did not have any problems braking or steering. Driving at 60kmh the truck goes straight until i gently brake, it will slightly pull left.
View 2 Replies
Yesterday while driving, i lost all power steering and power brakes (you would automatically think Booster). I pulled over, popped the hood and fluid was spewing from behind the power steering pump somewhere. I limped the truck home about 20 miles. I checked brake fluid and it was full. checked power steering fluid and it appeared to be empty. Yet when i added fluid it took less than a half quart. I started the vehicle to pressurize the pump and find the leak. Yet the pump never pumped any fluid. (one would thing pump was out) I am baffled as to if the pump went out, why fluid loss? If the booster was out, why do i still have brakes just without power assist? Andif a hose is blown, why such small fluid loss? I dont want to just start replacing parts till it get the right one
View 1 Replies
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 Replies
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 Replies
Brake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 Replies
On braking my front brakes locks up and there's a screeching of tires. Once I release the pedal all seems fine...or is it?
I dissassembled the front brake calipers and cleaned out the cylinder bores and blew out any contaminants from the line. Reassembled and bled the system only to find the pads doesn't move as freely from the rotors as they should. C-clamped the cylinder as far back in the caliper as it will go, pumped the brakes and still the rotor doesn't move freely from the pads, when the pedal is released...which accounts for the radical "loss of power", as the front brakes are holding on.
Bare in mind the vehicle hasn't seen the long road for almost 5 years and has been under the grinder/ welder/ primer/ sanding for most of that period and only moves out in the driveway when it's a good day to work outside.
New flex hoses? Flush the brake fluid from the whole system and start fresh? New caliper rubber seals? Blow the lines out with compressed air to rid of goop? New proportioning valve?
View 1 Replies
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 Replies
