Ford Brakes/Suspension :: 1994 F250 - Blown Brake Line / No Brakes At All?
Nov 21, 2015
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
View 14 Replies
Advertisement
Before I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
View 1 Replies
I had a leaky brake line behind the gas tank on my 2000 f250 superduty and in the process of fixing that I ended up changing all my calipers and brakes. I've bled the lines and there is no air left in the lines but the brakes are still soft is there something else that needs to be bled. I think all brake fluid leaked on the floor when the line broke.
View 10 Replies
Using a line lock as a parking brake? Going to switch to 4 wheel disc wont have parking brake.
View 10 Replies
I have a 1999 Subaru Impreza Wagon that I have owned for about 2.5 years, and I love it. I travel for work and I use rental cars alot. I have noticed in the past year that my brakes feel softer than most cars I drive, but I figure.. they are new cars, and my car is pretty old.
In the past 2-3 months I have notices a pulsing in my brakes...it sounds/feels kinda like the ABS, but I was thinking it would be worth getting my brakes inspected soon.
Then this past week, I totally blew a brake line when I was driving.
The car has about 140,000 miles on it and the mechanic says a brake line alone may not be related to the pulsing sounds...because brake lines usually go because of rust....
So...thoughts on things I should be looking at? What could the pulsing be a symptom of?
if one brake line blew, and it is rust, is the other one not far behind? (this was a new england car up until 2 years ago)
View 4 Replies
Rear steel brake line ruptured the other day (was pretty rusty). Despite being an idiot in regards to automotive repair (among many other things), I decided to give it a shot. I was able to get the damaged section off, went to Autozone with the broken piece, they matched it up, were nice enough to cut it and put on one larger fitting (because the two were different sizes) and flare it for me.
I was able to get the one side (at the T fitting) on OK. That was the "new" side, the one they flared at Autozone. Looks good. No leaks.
The stock side, at the passenger side caliper, leaks like crazy. Not out the threads, but out the hole through which the line passes. Know what I mean?
I'm having a hard time figuring out what's happening, because I'm not sure how this thing works. Does the line fit flush to something inside the connection at the caliper? Is it a bad flare?
It did not go in easy, but the new one was just as much trouble as the fitting that came out (stock?), so it must be right.
View 9 Replies
The brake line on the passengers side went bad. Called ford for replacement and they said ford is not supplying that line any more. Where I can get a replacement? Its hard line and connects to the rubber line.
View 2 Replies
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
View 4 Replies
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 Replies
Brake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 Replies
I have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems i was having the the speedometer and the transmission not shifting correctly.
Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles? Had to push the truck hard to get it back to my house, a mile or so. If i let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on.
It was not on before but i am pretty sure the ABS is disabled on the truck. the wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
View 1 Replies
92 F250 4x4 with 140,000 mi. Abs light came on, Replaced the sensor on the rear axle, Light is still on. When the light comes on the brakes still work but it takes more pedal to stop. Now the Brake light comes on, It has new pads on the front, and its bleed out good. When you drive it some times it works fine, then out of the blue it lights up.
I have checked the fluid level, parking brake switch, and even swapped the abs black box with another, also bleed the bleeder on the left frame rail. When the lights come on you can pull off the road and turn off the motor and restart the lights stay off for several brake applies, then sometimes they light back up. The light issue is not that bad to me but it drives my wife crazy. I am more concerned about it taking more/harder pedal to stop.
View 8 Replies
I just replaced the front break pads. I didn't replace the rotors or get them machined, didn't look like they needed them. Once I pushed on the brakes (truck off) I noticed that brake fluid spilled out the brake reservoir. I'm guessing it happened when I compressed the piston into the caliper? I took some of the fluid out of the reservoir and now its at MAX (I didn't bleed them). I've only been only be able to stop and go on the driveway (I'm waiting on a new radius arm bracket). The brakes seems spongy, the brake hits the floor. ABS and Brake lights came on then turned off once I started to pump them when I turned the truck 'on'. Do I just need to actually drive and "break" the breaks in?
View 2 Replies
My buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 Replies
So it looks like there is no adjustment on the Parking Brake on this ride other than adjusting the shoes up. As far as I can see my Parking Brake should work like a champ, but it won't hold on much of a hill. I have new shoes, new drums and it is adjusted up so I can hear them drag. I can actually feel it getting tight then looser as you spin the wheel, like one of the new drums is slightly out of round, so I don't think I could go much tighter. Is it possible one or more of the cables is stretched? I did see the shoes spread when I had the drums off and I stepped on the Park Brake, so I know things are working at least that much.
View 2 Replies
I got my grandpa's 84 ford f250 its been sitting in the barn for awhile but i drove it over to my house yesterday and it drove fine but you did have to push on the brake quite a bit but not to bad but today after school i took it for a drive around the block and i noticed that when i was going down hill just coasting i was slowing down a lot and my foot was not on the brake but when i got home my breaks were smoking pretty good but tomorrow i was going to take the front breaks off (its only the front two disk breaks doing this) and clean all the rust off them and put a little oil on the piston on the caliper that pushes on the break pads...
View 1 Replies
When depressed the break peddle is firm, when released break peddle does not return, replaced mc and booster, bleed breaks. Still having same problem.
View 1 Replies
I have a 2005 F250 Power stroke w/ brake controller installed. There is no voltage to the trailer brake (blue wire) pin. I've checked all of the fuses and they appear to be okay.
View 5 Replies
Recently purchased my first Ford truck, a 97 F250 w/7.3L diesel. I discovered the passenger rear drum brake was full of oil. Cleaned it up and put it back together to do some research.
I see how the hub comes off and there are two bearings in it an an oil seal. The bearings are lubed in wheel bearing grease. Does differential oil circulate through the bearings too?
It doesn't look like a difficult job. Do the seals go bad often or could this be due to a clogged differential vent? Truck has only 100k miles. Any gotchas I should be aware of?
View 6 Replies
