I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 RepliesI was wondering if there was how to on doing the MC replacement? The brake pedal goes to the floor almost every time you press on the brake?
View 1 RepliesWhy the brake lines have 2 or 3 coils in them near the master cylinder? Makes it a real pain to work on anything down in that area. Always snags ratchets and stuff...
My brother and I were discussing it the other nite, and the conclusion we came up with was, the first guy ever who was installing a brake system had tubing that was a couple feet too long, and couldn't find a tubing cutter, so he coiled them up.
Then the next guy saw that and figured "hmm, so THAT'S how it's done", and so on... Kinda like the story about the lady who always cut off both ends of her ham before she put it in the broiler..
I have a 79 f150. I changed two brake lines and master cylinder and bleed,and more bleed,but still very soft all most to floor? wheel cylinders look good.
View 2 Replies1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cyclinder need rebuilding or is my vacume diaphragm going. Not sure thats what its called.
View 14 Replies2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 RepliesA few years ago I (for him) replaced all 4 calipers, rotors, pads, etc....things were good. Just recently he replaced his Brake Booster and Master Cylinder (not sure what led to this), but long story short everything is back together and he doesn't have brakes.
My GUESS is that the system needs a good flush, new fluid, etc....
My problem is I'm unsure how to bleed the ABS system. A few google searched indicate I need a scan tool, but is there another way? Can I jump something.
So my question, how do I completely bleed the brake system on this truck?
I have a '79 F150 4wd and was wondering what would indicate a caliper needing replacement. I'm already going to replace everything on my rear brakes, they are completely trashed. However, the fronts seem OK, NO indications of leaks or seizing both sides of the rotors appear to be evenly "used" I guess. The inner pads do seem to be thicker than the outer pads is this normal? Anything I should be specifically looking for before I have the rotors turned and put a new set of pads on?
View 5 RepliesI have a 2001 F150. Front brakes replaced a few months ago. Last night, I realized my rear brake lights weren't working. I'm not sure how long they've been out or if it's related to the bigger problem.
While testing the brake lights by pressing the brake pedal, the pedal seemed to give out and sink lower. While driving the brakes worked but only when I pushed the pedal all the way in. Eventually the ABS light came on and stayed on.
I have a '53 Ford F100. I have a PB conversion kit on it. The master cylinder & Booster are under the floor. I have used this setup for many years. Recently my master cylinder went bad. I replaced it with the same model. I bench bled it, and installed it. I also added a remote fill kit, since it's difficult to check & fill. Because of the booster, the master cylinder no longer sits under the hatch in the floor.
I got everything installed & connected, then bled all 4 wheels using a bleeder kit with an electric vacuum pump. The fluid runs clear & no bubbles, but I can't get a pedal by pumping. I have no leaks. I tried with the engine off, and running. I have felt soft pedals before, but I have no pedal at all, it just goes to the floor.
I am doing an sas on my 93 f150 short bed. my issue is that I've made coil spacers out of 1/2" thick by 3" tall by 4" in dia.... as you can see strength is not an issue here. i bought 6" lift coils for a 93' then decided to just say f it and throw a d44 straight axle under it. the springs on a 78' d44 are the same dia. top to bottom. 93' springs get smaller at the bottom so i made this spacer for two reasons.... 1 to have smaller seat for the bottom of the coil.. and 2 so i could make up the spring length difference between the two springs. The spacers are leaning forward due to the 7 degree c bushings on the radius arms.
View 1 RepliesI have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
I just replaced the front break pads. I didn't replace the rotors or get them machined, didn't look like they needed them. Once I pushed on the brakes (truck off) I noticed that brake fluid spilled out the brake reservoir. I'm guessing it happened when I compressed the piston into the caliper? I took some of the fluid out of the reservoir and now its at MAX (I didn't bleed them). I've only been only be able to stop and go on the driveway (I'm waiting on a new radius arm bracket). The brakes seems spongy, the brake hits the floor. ABS and Brake lights came on then turned off once I started to pump them when I turned the truck 'on'. Do I just need to actually drive and "break" the breaks in?
View 2 RepliesWhat would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 RepliesMy rear brakes lock up constantly. It doesn't matter how easy I am on the peddle. The ABS goes through it's test on start up. Afterwards, the light goes out. The vehicle sat for quite a long time. I pulled the rear drums and inspected for rust and brake shoe condition. There was no rust to be found and the shoes seemed to be in good shape. I've read on here about some shoes retaining moisture and causing the same thing. These 'seem' dry. I've also read that it could be the RABS. Is there any testing to determine if the RABS is definitely the problem other than by-passing it?
View 9 Replies92 Regal Custom, 3.8L .... I need to replace master cylinder on mother in laws car. How do I determine if it has the Durastop brake system or not?? Any factory code in glove box or trunk, if so what is the code to look for?
View 2 RepliesI am having trouble big time getting air out of my brake lines. I put new front pads and rotors on and also had to replace the brake line coming from the caliper as it kind of crumbled and needed to replace the next line up that goes to the ABS block on the left front. After doing this, I bled that wheel only and at first it was ok until the brake line on the right front at the caliper also broke when I was pushing on the brake pedal with the truck running, spewing fluid all over. I have tried to bleed using a decent vacuum bleed setup from Advanced Auto but keep getting massive amounts of air coming out and when I start the truck and hit the brake pedal, it goes to the floor. Could the master cylinder be bad? I have checked every connection that I made and all other connections and there are no leaks at all. I am stuck in the garage! The truck is a 1999 F150 4x4 with 4 wheel ABS.
View 1 RepliesSo it looks like there is no adjustment on the Parking Brake on this ride other than adjusting the shoes up. As far as I can see my Parking Brake should work like a champ, but it won't hold on much of a hill. I have new shoes, new drums and it is adjusted up so I can hear them drag. I can actually feel it getting tight then looser as you spin the wheel, like one of the new drums is slightly out of round, so I don't think I could go much tighter. Is it possible one or more of the cables is stretched? I did see the shoes spread when I had the drums off and I stepped on the Park Brake, so I know things are working at least that much.
View 2 RepliesI recently purchased a mutt of truck, a 97' F150 heritage w/5.4 Triton motor, 1/2 ton 2WD short bed.
Having a brake issue, the pedal keeps fading. I noticed it first while sitting in traffic on a down hill grade. I am holding the pedal and notice it starts to creep down slowly, I pump it up and it firms up then starts collapsing again. So general logic says hydraulics are loosing pressure right?....No leaks anywhere, so it must MC tight?
I have replaced the master cylinder, brake booster, and both rear wheel cylinders. Long story short they all needed it, truck has 265K+ on the body with 95K on the motor. The only thing I did not do by standard is bleed the MC on the bench, I installed and long bled starting with the right rear working my from longest distance to shortest (wheel speaking). So when bleeding I did of course get air coming out because of the new parts but I still have the same fade issue.
I am confident there is no air in the lines, I have bleed a quart of brake fluid through just to be sure. I have read a lot about proportioning valves and ABS stuff.
I will try and get some vehicle specific photos and attach have hit a road block with this. I am leaning towards the ABS valve thingy mounted on the drivers fender that has four lines attached (2 in and 2 out). Other than that it comes down to hard lines which have no leaks.
I have a '90 F150 and both the yellow ABS light and the red BRAKE light are on.
It was fine until my buddy did a little brake work for me, including replacing a couple brake lines and a parking brake cable. He bled the system at the lines going into the front calipers because the bleeder valves on the calipers where corroded and frozen. I then replaced the calipers and bled the system properly. Three times. I don't think the problem is from the brake work.
The brakes still work, by the way. The pedal just feels a bit spongy and I think the brakes don't work as well as they could.
If the truck is not running, I can pump the brakes a few times, and it will make a sound like it's sucking air a few times. Then the sound stops and the pedal firms up.
If the truck IS running, it keeps making the sucking air sound no matter how many times I pump it, and the pedal feel stays the same. I think it might be a bad brake booster.
I took my 2010 F-150 for brake job and ended up with brake fluid in intake!! How that happened?
View 12 Replies