I have a 1991 F250 Lariat, 4x4, 460 engine, auto trans. I am having trouble with my steering. The power stering turns good to the left but when I turn to the right it is like there is no power and is very tough to turn.
View 1 RepliesOne my F350 with 175,000 miles on it, at low speeds when turning the steering wheel it seems as if it has two places during use that it rubs or has an oblong spot in it. I have 285 tires on it and have for years.
Kind of like if you were turning a shaft in a seal and it rubbed or was rough. It makes a faint, muffled, barely audible grinding noise or feel. I have a lift and level of about 4" and 285s for years. This just started in the last 5 months or so.
I have a 2010 F250 King Ranch FX4. I have an odd problem that I am trying to get to the bottom of. We went on a 2,500 mile road trip last year and I noticed on the way home my steering wheel had worked it's way off center counter-clockwise at a perfect diagonal. I had gotten an alignment right before we left and it was perfect center at that point.
I took it back in when I got home and had a tire rotation and another alignment. Within a week the wheel was off again to the same degree, counter-clockwise at a perfect diagonal.
Two weeks ago... tired and annoyed of driving like this, I crawled under the truck and adjusted the steering wheel to center via the drag link adjustment. I tightened everything down tight and this lasted all of three days.
Wat would cause this? Tires are wearing normally, alignment checks out and it tracks straight. I do see some grease like leakage where the pitman arm meets the top of the drag link and again have some small grease where the drag link connect to the passenger side tire. I lifted the front end and tried to move/wiggle the tires and I have no movement... everything is solid. The truck never wanders when on the road... steering wheel is just off.
Truck only has 90k on it of highway miles and an easy life thus far. I am not hard on the truck.
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 RepliesBefore I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
I have a 2008 f350, crew cab,6.4L. with 27,173 miles. may have a problem with the steering, seems to be tight when turning from left to right or right to left, doesn't seem to center, if I turn a little to left or right it stays there. I can go in complete a circle. Raised front off ground turns ok no binding, nothing loose on the front end.
View 1 RepliesLooking to replace the steering stabilizer on my 2008 F-250. It has a 6" lift and 37" tires.
Also, does "dual" mean better?
2000 f250 with v10, got home from work today, then short time later we were going out again and my steering was extremely loose. Basically you could swing the wheel and it spins around. Power steering fluid was empty and I refilled it but still the same problem. Is there possibility that I'm just not using a thick enough power steering fluid?
View 1 RepliesMy 97F250, 7.3 diesel, 4WD has an intermittent steering issue. When I come out of a turn, it doesn't want to come out of the turn all the way. It will keep pulling one way, and I have to jerk the steering wheel in opposite direction, and sometimes the truck then over corrects quickly the other direction. Mechanic said front end looks good, so he replace the power steering pump. That didn't work...
View 4 RepliesI have a 1993 f150. Problem is that the steering wheel can wobble back and forth about a half inch or so. I took the wheel off and it looks like there is a lock ring holding everything in place. I just wondered if there was a solution to this to fix it
View 1 RepliesStarting having a problem with the front suspension on my 01 excursion. When you go over a incline I am getting a big bang in the front suspension also when you turn the steering wheel to the middle it has a jerk right before its in the straight position.
I have new wheel bearings and new locking hubs coming, this problem still happens without the hubs in. Could it be a front axle or U joint but it happens with the 4x4 disengaged.
I have a 2009 screw with ~60k miles. It is used for DD and tows our small camper or my flat deck w/jeep.
The other day I noticed an issue when turning right. The wheel gets hard to turn and does not want to return to center. There is also a low speed clunk you can feel in the steering wheel/column itself.
The truck is at the dealer now and they said the rack needs to be replaced and there is something in the column they need to replace too. I have the extended warranty, so this is all but covered 100%. I just have a deductible to pay.
I have not hit anything with the truck, so I am not sure what caused these issues.
Starting about a year ago, "sometimes" when I step on the brakes and am turning the steering wheel, I loose the power steering. I took it to Ford and they said that this is a a known issue but they didn't say what it would take to fix it. Because this problem is intermittent it is very hard to get this fixed unless the mechanic can experience and verify the problem for himself...
View 14 RepliesI had some steering issues with my truck so took it for an evaluation at pep boys. They recommended a new steering gear box and tie rod that hooks to the pitman arm so I had them replace them. Steering was improved but now the wheel is canted to the left or right depending on when I make a turn. When I make a left turn, the wheel is canted about 10 o'clock. When I make a right turn, it's canted about 1 o'clock.
I looked under and had my brother turn the wheel and didn't really notice any thing loose. I lifted the front and noticed the left wheel bearings need to be replaced. I also noticed the shocks were shot and replaced them but it didn't make a difference in the crooked wheel.
Do you think it's the wheel bearing that can cause this? How about the ball joints? The truck has 407k miles and I bought it a month ago. Previous owner said he never replaced any steering components. Should I just replace all steering components with the Moog kit? I'd like to hold off on the $600+ kit for now as I just bought a a boat and the boat needs some stuff. I hope to find that one thing (hopefully not more) that's loose.
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 RepliesI have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 RepliesIf this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 RepliesBrake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 Replies