I have a concern with my serpentine belt chirping when it's wet or cold. I have tried soap, and other attempts to quiet it down. Belt tension is good, new water pump and fan. Otherwise no other issues so far.
View 9 RepliesI was driving the other day (cold weather- approx 15 F), and my serpentine belt shredded. Managed to drive a mile or so to my driveway. The belt was shredded on the fan side (and had come completely off), but it wasn't torn in two. Got a new belt and installed it, but upon test-cranking, found that it was riding up one ridge on the crank. All the other ribbed pulleys were fine (PS, AC). The smooth pulleys had the belt move a little, however.
Thinking I didn't set it right, I reinstalled the belt on the crank and tried again. Same result (belt rides up one groove, towards the fan). I perused the archives, and one comment was that someone simply trimmed one groove off the belt and everything was happy. The belt found it's "groove", and didn't act up anymore. Doesn't fix the underlying problem, but
1) is this a good fix
2) any clue what is going on?
3) Do I need to get the crank fixed?
BTW, I am sure that I threaded the belt on correctly!
1992 Aerostar, 4.0L, AWD. AC+P/S....
I have 1997 F250 LD since i bough it has been doing this chirping sound coming from the serpentine belt and the pulley area but when the truck has been working for 15 - 20 min it goes away
This is apart from the from the problem before I think the fan clutch is broken because when I start the truck I can hear the fan going at the same speed of the engine is that normal ? even when the truck is cold
I have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 RepliesWell, started to get belt squeak during cold starts. The idler pulley was changed many miles ago for same issue, but it seems to be starting up again. There are NO tutorials for serpentine belt replacement on this gen of RX.
View 14 RepliesI was wondering because serpentine belt is a big thing for 05 corolla since everything runs on it. I also had a 94 camry which had a alternator connected to a belt. and if i wanted to tighten up that belt i would just loosen the alternator and pull it. Is there a way to tighten up serpentine belt in my 05 corolla in the same way?.
View 1 RepliesWhat a Serpentine Belt is? (how much is it for that part alone and to install at the dealership?)
Dealership told me why during the cold mornings after I start the car up, it is creaking and squeaking........
They told me it needs to be replaced?......
When it is cold out or wet my serpentine belt squeals a lot or a couple of minutes. It had progressively gotten worse this past winter. The shop said the belt looks fine and Toyota wants me to pay for them to look at it...
View 2 RepliesI have a '06 sonata 3.3 v6. Let me first describe what was happening to the car before the noise started. When I first started the car and put the ac, the first time turning the steering wheel in either direction the steering wheel would tighten up and the battery indicator light would come on and the fasten seatbelt light would flash even though I had the belt fastened. It would only happen the first time I would make a turn and after that I could turn with no problem. So in recap, it would only happen on the first turn and only when the ac was on. Now when I start the car up there is a noise coming form the pulley/belt area. I wouldn't classify it as a squeaking noise more like a grinding. I've looked at the belt and it seems to be fine. After I start to drive the car the noise goes away. If I start the car again after a drive within about 2 hours the noise doesn't happen when I start it. What this noise could be? and also could the noise and the steering wheel tightening when the ac is on be connected?
View 1 RepliesThe serpentine belt starting squeaking on cold and damp mornings about 18 months ago at about 60K. I replaced it with a Dayco belt, and the noise went away for about 6 months. When the weather turned cold last winter, the noise came back. So I changed the tensioner with both idler pulleys right about when the weather warmed up, and it was fine all summer. Now that it has gotten cold again, the squeak is back yet again and as before it goes away when the car warms up. I know it is the serpentine belt because when I spray it with water the noise immediately stops. I checked all the pulleys with the belt off and when I spin them I hear no noise. Is there something else it could be?
View 1 Replies2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 RepliesI have a 2003 f150 4.2 v8. and i have a squeaky belt I am almost positive its the belt i went to change it today but being sick,cold (NY), getting dark having just worked 10 hrs and changing oil it was not going well.
The reason I think its the belt it does not squeak when its really cold out but once it warms up a little its back so I am thinking when it gets warm it stretches out a little and when its cold it shrinks up or am I just crazy..
So i have a 1998 4.0 ohv ranger and have been fighting belt squeak shortly after i got it. I've replaced the belt twice and the tensioner twice when i put a GATES belt on it stopped for like month. But its still squeaking. If i put a wrench on the tensioner and turn it the squeak stops. So i need to find a way to tighten the tensioner could i somehow jam it, our hook up a turn buckle bolt to manually tighten it, or use a different ford tensioner. I really need to do something cause this squeak is just down right annoying.
View 2 RepliesMy 2007 Ford Focus broke down today. From what I can see and find online with my limited knowledge, it looks like the serpentine belt broke. Would this cause loss of power steering, rise in oil temperature and my check battery light to come on?
View 11 Replies2003 3.0 ranger... This will be my 3rd time replacing serpentine belt and if needed 2nd. time for idler, tension pulleys...NOT SURE WHAT TO DO, should i replace parts again?
View 5 RepliesI've been having trouble with my 2000 EX recently, I've had to replace the serpentine belt 3 times in the last year and a half. Nothing looks out of place but I really don't know enough about this engine yet to say that conclusively. I've been using the regular belts from napa, so this time I ordered the HD belt. Is there something that I need to look at that maybe misaligned that could be shredding these belts
View 13 RepliesLeaving on a 200 mile trip in the morning and when checking the fluids, I found the serpentine belt trying to get off the AC pulley. I've put in on twice and it immediately jumps half way off when starting the engine. How long it's been doing this. Nothing is obviously loose or moved. What is likely causing this?
View 8 RepliesI have a 2006 Escape with a 4cyl. 2.3L automatic gas engine. Recently when going down the road my serpentine belt broke. I purchased a new one and attempted to install it. However, after routing it over all the pulleys there is still a significant amount of slack. Keep in mind when putting the new one on I didn't even have to move the tension pulley. Upon starting the vehicle I was able to see that all of the pulleys were moving and doing what was expected.
However, there is a great deal of squealing and risk that the belt with be thrown off or broken. I researched and am fairly certain that it is in fact the correct size belt as all the sites indicate the same part number and size. Could this be the result of a bad tension pulley that needs to be replaced? Need access to the routing diagram in case I may have put it on incorrectly? Am I missing some other form of adjusting the tension in the belt?
So, my "new to me" 04 Excursion makes a belt chirping sound for a second with hard acceleration, usually 2nd gear, not always, but should I be concerned, I can't tell if it's the transmission, it does NOT appear to be slipping. I googled the scenario and people are mentioning a tensioner or belt that should be replaced.
View 10 RepliesI noticed my serpentine belt started squeaking about 3 days ago. And yesterday as I was driving to work I heard a clicking sound coming from the left side of the hood, then my car started to gradually shut down and white smoke was coming from the engine. When I got to the stoplight it completely turned off, but I was able to turn it back on again to turn into the parking lot before it shut off again. When I checked it there were no visible leaks, my reservoir for my coolant was still full, and my meter never went up indicating that my car was over heating. I'm not sure what's wrong with it, but after it sits for awhile it is able to turn back on again for a while.
View 3 Replies