My friend has a 97 Aerostar swb panel van. It's a 3.o with an automatic, with the code of death P1744. For the price of a rebuild, he would rather put a manual trans in it. What trans will fit, and what needs to be done as far as electronics goes?
View 8 RepliesI got this code and symptoms of 1-2 hard shift and no torque converter lockup. No flashing overdrive light on shifter. If I switch off engine all shifts are smooth until I pass 45mph. I would feel the TCC lockup. This doesn't happen the as i come to a stop I get a harsh 2-1 shift. Key off restart then shifts smoothly up and down provided I dont exceed the TCC lockup speed. This leads me to the TCC solenoid I think. Fluid has been changed regularly.
Had to drive 300 miles to get home. Only for the plate trans cooler the fluid would have overheated as on inclines on cruise control the engine would rev to 3k to keep the speed at 70mph and I could see the fluid temp increasing. Fuel consumption was very bad almost a full tank (with no ac). Doing some research there is talk about valve gasket blowout Epc solenoids etc, though these were for Rangers and Explorers, no real mention of Aerostar.
Just curious. is it possible to convert my auto camry to manual transmission? also, how much would it be? where can i go?
View 5 RepliesI have a 2007f550 auto trans with a flashing tow/haul light and a code of po791 coming up. Flashing light will clear in k/o position and remain off until placing selector in drive,after two feet or so of travel,an audible clunk and the trans acts like it is in third gear. Reverse is no change and highway will not shift into o.d. The iss "A" is listed as the culprit but ford doesn't list a iss a.
View 2 Replies2002 Ford Escape... My OD light started to come on every once in a while, and would go off once I turned the car off... This being said, as far as I could tell, the tranny was running smooth. Then an engine light popped on and this code and explanation come up... P1744 "Torque Converter Clutch System Stuck in OFF position".
I recently came back from a bit of a trip... and after shutting the car off, it didn't want to restart. Since this time, the car has begun to start, but the engine light remains on with the P1744 coming up...
Research seems to indicate that the problem is with the Torque Converter Solenoid. You Tube videos show that there are two solenoids just under the transmission pan...
I have a 2000 expedition with the 5.4L and a squirrel got under the hood and chewed up some wires that run to the pcm along with some vacuum lines. I got all the wires I seen spliced back together. I drove it yesterday for the first time and my check engine light came on. I pulled a p1744 a trans solenoid for torque converter lock up. The fluid isn't low and looks bright red on dipstick. It drives and shifts fine. Is there a certain wire from the pcm harness I need to look at first?
View 14 RepliesAfter multiple problems with this vehicle already, it's about time that I made an account.
We have a 2003 Escape XLT with around 150k on it, and are now having transmission issues.
It's slipped some when cold and starting from a full stop and sometimes rolling stop, when trying to accelerate. Basically, it acts like it's in neutral until the gears "catch up". Once it's warmed up, it's fine even on steep hills. Also, going in reverse seems to act normally oddly enough.
We were hoping to get through winter as it was since it was easily manageable, but yesterday the O/D light started flashing and we have the pending error P1744. Nothing happened when the error came on including the normal slip since everything was warm at the time.
We'd of course, love to avoid completely replacing the tranny, but I'm mostly learning as I go with this one. Where to start narrowing out possibilities? The fluid was changed when we first got the escape about four years ago and is still at the right level and clear/red.
I have a 1992 Aerostar Sports edition. My clock spring went bad like 6 months ago. I couldn't find a replacement anywhere. Not even at the Ford. I went to different junkyards and couldn't find the same exact one. Since I wanted to change the steering wheel anyway, i got the steering wheel and the clock spring from a 1999 Ford Explorer Sport at the junkyard. The clock spring fits perfectly and so the steering wheel. My only problem is that clock spring harness is different. I have no problem with the steering wheel side since both the steering wheel and the clock spring came from the same car. But under the dash is a different story. I have the manual for my Aerostar with the wiring schematic for the speed control system (cruise control) and horn but i just can't find the one for the 1999 Explorer. I got one for a 1996 Explorer and have the same wire colors than the clock springs i got from the 1999 Explorer. But i want to make sure I got the right schematic to feel confident I'm doing the job right. I can also use another version for the 1992 Aerostar because mine is a little confusing.
My old clock spring had two harnesses. One for the airbag which I am not going to use (i don't like airbags) and a second one for the cruise control/horn. This harness had four wires. One thick black one that goes to the casing of the ignition switch, and three smaller wires (BK, LB/BK, and Y/LB). The clock spring from the 1999 Explorer has six wires on that harness. One thick black that goes to the ignition switch and five more smaller ones (BK, LB/BK, DG/O, Y/LG, and R/BK). Going by the two schematics i have them figured out (i think), but want to make sure.
I was just wondering is the climate control self contained so it can be directly swapped for manual HVAC controls? I have a XLT and would like to upgrade the HVAC and radio system if possible if they are direct swaps.
View 3 RepliesI was thinking the other day, wonder if a 66-77 bronco 9" axle would work, width wise, on an Aero? Obviously, you'd have to grind off all the mounting brackets and add the Aero ones. Mostly just building the "ultimate Aero" in my mind,
View 5 RepliesI'd like to know if a 2nd row captains seat can be use as a replacement for the 1st row driver's. I'm referring to the seat section itself, not the entire frame. I found some excellent condition seats but they are from the 2nd row. My Aero is a '95 and I don't know(yet) which year van the seats came out of.
View 11 RepliesI am in the middle of the 7.3 to 6.0 swap and wanted to confirm the in and out lines of each cooler. All the links to the websites that were writeups seem to be dead.
View 3 RepliesI have a 1999 mercury cougar and recently my acceleration has gone down huge, when i try to go onto a highway my car starts to chug, i have to push the pedal to the floor for it to actually start picking up speed a little faster, and once in a while i smell a sulfur smell!
Another symptom I have is my engine heat goes up 3/4 of the way when this happens! Also once in a while after driving while its hot the car starts to shake lightly then shakes a lot until i get off the highway and bring my speed from 110km/h to about 60k?
Engine codes: p1744
I am looking to change out my manual transmission in my 79 f150. I want to put a 5 speed in it but still keep my manual clutch. I have a 300 engine that I also want to keep, can I just put a late 80's early 90's 5 speed transmission in it and keep my original bell housing?
View 5 RepliesI have a 2001 F250 with 7.3. We swapped the auto for a zf6 manual. We left the auto's shift position sensor tied to the frame and left in neutral. I did install a pcm from a manual transmission pickup. Also have the clutch position switch hooked up. I have an Edge Evolution CTS2 reprogrammer, and on the display the gear indication always shows P. I suspect that is why my cruise doesn't work. For interests sake, I tried manually adjusting the shift position sensor through all gears, and the reverse lights come on when in reverse but the Edge's display always shows P. My question is with a manual transmission, how does the pcm know that it is in gear? The only sensor that I am aware of is the reverse sensor on the zf6.
View 4 RepliesBought truck for cheaper price with no 3rd gear. Went to a reputable yard and picked up a cheaper trans... It was carfaxed with 185K miles and in a rollover. (This is the last time I try to save a couple bucks by getting a cheaper transmission.)
I believe trans is stuck in 3rd gear...Takes off slow. RPMs do not drop..Doesn't shift...Feels like I'm in 3rd from takeoff. Here are the codes:
P2262: Turbo / Super Charger Boost Pressure Not Detected Mechanical
P2614: Camshaft position signal output circuit / open
P2262 again
P1000 On board diagnostics II Monitor / drive cycle test not complete
P0678 Cylinder 8 glow plug circuit
P0672 cylinder 2 glow plug circuit
P0603 Internal control module keep alive memory malfunction
P0720 output shaft speed sensor circuit
B1676 Battery pack voltage out of range
B1318 Battery voltage low
I have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.
View 14 RepliesI am planning a swap in an Excursion from the automatic to the manual transmission.
How will I need to modify the wiring harness to make sure everything still works?
Things I can think of that will need addressed:
Harness for the brakes (Neutral Safety Switch?)
Harness for the clutch pedal
Cruise control harness differences?
Back up switch wiring?
Ok so I've done a lot of searching but can't find any info on how to repin the harness to use the 2000 4r70w in my 2002. Both are 4x4 and came behind a 5.4.
View 4 RepliesMy dad has a 2006 F-250 5.4 3v that spun a rod bearing at 107,383 miles. He's never been thrilled with the performance of it (told him he should have gotten the 6.0 when he bought the truck new, but why listen to a 15 yr old ). We've been throwing around a couple different ideas for engine swaps since the 5.4 is dead. We scored a 5.4 2V Lightning engine, but after trying to figure out transmission controllers or if we'd be able to tune the stock PCM for the 2v, we've put the project on hold.
Recently, I've been trying to convince him to do a diesel swap over the L-motor. I have a friend selling a cheap 99 7.3 with trans, PCM, harness, intercooler, piping and other misc stuff. Would that harness generally be plug and play with the body of the 06? Would it be more worthwhile to try to find a 6.0 from 05-07 and swap everything over?
I've also been considering a Cummins swap, although I haven't gone much past looking at complete engines on eBay and Craigslist. Would this be the better route, and just get a standalone controller for the 5R110?
So I'm looking for other's opinions. Should we go 7.3, 6.0 or Cummins? Should we stick with gas over diesel? Try to make the Lightning motor work? Or just go back with a stock 5.4 3V? I should say, he won't sell the truck for whatever reason, so he's not worried about resale or anything. We're in Michigan, so we don't have to worry about emissions. And we're fairly mechanically inclined, so I'm not too worried about doing the swaps, however my knowledge on diesels is limited.
About a month ago my van did the thing where it dumped four quarts of trans oil onto the exhaust creating an awesome smoke screen. I would like to avoid this happening again. I plan on adding a second trans cooler in series with the factory one. If the trans fluid goes through the radiator or trans cooler first?
View 3 Replies