Ford Aerostar :: 1997 - Grinding Noise From Steering Wheel?
Aug 11, 2012
'97 Ford Aerostar, 155k miles. Airbag model-
The problem: When I turn the wheel, there is some grabbing and tightness, and a strange grinding noise from the top of the steering column, like, right under the steering wheel. What's more, the wheel will actually pivot up and down on the steering shaft. I have tried pulling on it, and it loosen the grabbing, but it won't pull off in my hands or anything....
I suspect a bearing in the upper steering column has failed or has come loose. I guess I need to pull the bag and look around- Are there any tricks to pulling the airbag?
View 10 Replies
Advertisement
I've got a 1993 ford aerostar. Today, my steering wheel started shaking/rattling when I turn the steering wheel. Seems to be more obvious when turning right rather than left, and is only obvious at low speeds.
Only thing out of usual was that the front had been on jacks for a few days for an unrelated (starter) repair. What to check or how to isolate? I imagine it has to do with the power steering but not sure what to check.
View 6 Replies
Ford Focus 2012 - 25,000 miles
There's a loud grinding noise from the front end of car when I turn the steering wheel... even when the car is off and in park.I can post videos of the noise if needed.
View 2 Replies
One my F350 with 175,000 miles on it, at low speeds when turning the steering wheel it seems as if it has two places during use that it rubs or has an oblong spot in it. I have 285 tires on it and have for years.
Kind of like if you were turning a shaft in a seal and it rubbed or was rough. It makes a faint, muffled, barely audible grinding noise or feel. I have a lift and level of about 4" and 285s for years. This just started in the last 5 months or so.
View 1 Replies
I may, or may not have had to jump a curb at 40 mph to avoid rear ending another car. Truck is a 2003 F-150, single cab stx package, 4.2ltr. Long story short, no damage to my passenger side front tire or rim that I can see, but I do have a horrible grinding noise when I turn the wheel either direction. The truck still turns properly, power steering fluid is level. What should I start replacing first?! She's got about 90k miles on it, I'm sure a lot of the suspension parts are due, just need to know where to start!
View 3 Replies
Lately my 2007 Camry (2.4 L, Auto) has developed a bit strange problem. When I'm driving on highway, even slight left turn results in a grinding noise and sort of resistant steering wheel. It happens only when I turn left. As soon as steering wheel gets back to straight, the noise and steering wheel resistance/hardness goes away. I don't really feel much when I'm driving slow on the city streets. Although some time when I am little bit fast, I feel slight grinding noise and steering hardness. No problem in turning right at all.
View 5 Replies
My 08 gx just started making this weird noise when I have I'm leaving from a stop and have the wheel towards the right. It sounds like a rubbing noise. This doesn't happen when I have the wheel turned to the left. Only the right.
View 10 Replies
1994 Chevrolet silverado 2WD 350/V8 ... I've been too focused on the loose steering and now there is a grinding noise feel on the steering wheel when I'm driving straight and above 20 mph. I jacked up the front end of the truck and after wiggling the front tires at 12:00 and 6:00, I can feel a slight movement at both front wheels. Is it a telltale sign the wheel bearings has failed. Note that I am deaf and can't hear any growling/grinding but I certainly can feel the grinding feel on my steering wheel. Wheel bearings it is?
View 19 Replies
I have a 1997 Ford Aerostar rwd with a 3.0 L v6. I would like to know how can I remove the power steering pump. Furthermore, the reason I am changing the power steering pump, is because I am changing the rack and pinon mechanism. Additionally, I found the rack filled with hydraulic fluid. If possible pictures would be a nice addition to your respond.
View 3 Replies
I just bought a 99 f150. Its in great shape only 65000 on it but there is a hissing swooshing sound when turning the wheel... not really any brake sounds. The truck has been maintained and I dont see any leeks in the ps system hoses. I didn't know anything about the atf fluid in the truck... and I haven't added either ps or atf fluid to it. I'm wondering if that is maybe something the dealer i bought it from did. or maybe one of the shops the previous owner did. Would ps fluid cause these kinds of sounds? Do I need a flush of the system.. How to do that.
View 14 Replies
I have a 1997 f150 4x4. When I put to 4 wheel drive on all I hear is grinding, but I'm pretty sure it works...
View 4 Replies
What would cause the front wheel on drivers side to lock up if it isn't the brakes. have been hearing a loud popping noise for a while on drivers side especially when turning left. Today got really loud just driving and then a real loud grinding noise. Then a loud pop and front wheel locked up and skidded across highway til i came to a stop. What it could be or how can i at least get wheel to turn to get it on trailer...
View 6 Replies
I have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 Replies
My 1997 4.0 Rear Wheel Drive is making a clicking noise when it is put into gear or when it switches from drive to reverse and vice versa. Sound is coming from the back of van. Does not make noise all the time. Drove 50 miles last night with no problems and minimal clicking. Could it be U-Joints going bad? Or is this a different problem?
View 6 Replies
Maybe I'm just too picky or my imagination is kicking in. In the last week or two, I noticed a grinding like feel on the stick, the steering wheel and the gas pedal (just a little, not too much), something like a bracket or plate loose somewhere and I can feel it more the faster I go. This can be reproduced by just pressing the clutch a little right up to the point where actually start engaging. I had the same feel on my Maxima and it was the heat shield. Am I alone on this one?
View 1 Replies
I get a grinding or whirring sound when I turn my steering wheel left or right. I gets worse if press the accelerator pedal. I believe it has something to do with the power steering but I don't know how to troubleshoot the issue....
View 5 Replies
I have a 2003 Sport Trac 4wd with 299,000 miles. There is what sounds like wheel bearing noise (grinding) that was noticed after returning from a trip where I flat towed it behind my rv. I did not notice the noise the last time I drove it - before towing it about 450 miles. I have towed this vehicle for many years and miles this way - transmission and transfer case in neutral with key in on position to unlock steering. I stated this part about the towing because the noise may have gone unnoticed for many miles. About 20,000 miles ago, I changed front wheel bearings, brake calipers, upper and lower ball joints, shocks and outer tie rod ends. Also rear brake pads.
I put the vehicle on jack stands and in drive mode couldn't hear anything in either 2wd or 4wd. I held one wheel at a time so the other side would spin. After checking for wobbling wheel bearings, I took off the wheels and did a push / pull on everything - all seems good. I changed driver's side wheel bearing anyway because I thought it to be a little rough. I removed the front drive shaft and took it out on the road. Noise was still there. This makes me think front differential but before entering unknown territory (for me) is there something else I can do to narrow down the problem? At this point, I'm not even convinced it is from the front end - maybe the sound is radiating through the truck.
View 3 Replies
Just installed new actuator and wheel hub assembly on my 2009 f150,truck still had grinding noise in front passenger wheel , New solenoid and vacuum hose kit installed when test drove noise still there until you put the truck in 4 wheel drive it disappears . The noise returns as soon as you take it out of 4 wheel drive. Also mechanic said steering was tight,installed new shaft same thing, could this be the rack and pinion.
View 5 Replies
I just recently bought a 2000 Explorer, 4.0 OHV, 4x4 with about 150,000 miles.
I've had the vehicle for about a month, and ever since I bought it, it's had a grinding sound (sounded like wheel bearing) coming from the front right side. I replaced both right and left bearing/hub assemblies, and took it out for a drive. The initial sound that I thought was bearing noise is still there, and at about 65mph I started to get a little bit of steering wheel shake. I took my foot off the gas and it stopped. I accelerated up to about 70mph and it seemed ok.
I hit a VERY small bump in the road and the steering wheel started shaking like hell. So bad that I almost lost control. I slammed the brakes and the shake stopped instantly. I took it home and put it up in the air, half expecting to see something loose or broken, and everything looks perfect. I re-torqued everything that I had taken apart for the initial hub/bearing replacement, and took it out again. Same issues.
I never had ANY of these problems before I replaced the hub/bearing assemblies, so I'm completely confused. I was thinking CV joints, but I have no clicking at all when turning, in forward or reverse, everything is smooth. Outer tie rods were done about 6 weeks ago..
View 1 Replies
I noticed the front diff of my truck was whining, so it decided to take a look. I noticed that the passenger side hub would not unlock when it was in the lock position. My truck has the manual floor shifted 4x4 and the manual hubs, not the ESOF. I removed the locking hub from the hub bearing assy and I noticed that the axle shaft still moved when i spun the wheel. I know the manual locking hub is trashed (pieces fell out when i removed it from the truck) but does the fact that the axle shaft still spins in the assy with no hub installed also mean that my hub bearing assembly is trashed and warrants replacement?
Finally, the number one most annoying thing with this "new to me" truck, is this noise in the steering column. It is very hard to describe, but when slowly turning the wheel, either left or right, it will produce a groaning/grinding sound that CAN be felt in the steering wheel. There is a roughness/vibrating/binding type feeling in the wheel when this noise is made. I lubricated the boot that goes through the firewall, and the spring around the shaft behind the turn signal switch with silicone spray and the noise goes on. It really feels like it is somewhere in the column, but as I said before I do not know anything about these superdutys. I work for chrysler and I have never experienced anything like this on a dodge truck.
Its not the best but here is a video, little grinding noise that I am speaking of is most noticeable when camera angle changes to the side of the column, just before door buzzer makes noise : Grind steering - YouTube .....
View 7 Replies
I noticed after the crash the steering wheel is moved forward and gear shift is up against dash. asked around and one person said they made collapsable steering wheels to impact. i have never heard of such a thing.
View 5 Replies
