Ford Aerostar :: 1997 - Code P1443 For EVAP System
Jun 2, 2003
My 1997 aerostar 3.0 6 cylinder, throwing code p1443 for the evap system. What should I be looking for?
View 5 RepliesMy 1997 aerostar 3.0 6 cylinder, throwing code p1443 for the evap system. What should I be looking for?
View 5 Repliesfinally found the reasons for the two Codes in my '97 4.0.
here are the culprits: Code P401 DPFE Sensor, found it on eBay. (The metal case sensor, nos)
Code P1443 Evap system Purge Sensor (also eBay)
Finally, CEL is off after replacing both sensors above.
Now I have to figure out the REAR ABS light, still ON.
I have a 1999 Ford Explorer with the V-6 SOHC that is stuttering and stalling when I try to accelerate. A very slight acceleration will get the vehicle moving, but anything coming close to normal gas pedal pressure causes immediate stuttering and/or stalling. Check Engine light came on when problem started yesterday.
Where is the EVAP System Canister Vent Solenoid? I bought a code reader after beating my head against the truck all afternoon and got code "P1451 EVAP System Canister Vent Solenoid Circuit Malfunction". My Haynes book says on the left side frame rail... can't find anything along there that looks like it (based on picture from Rock Auto for replacement part) and found some people online talking about it being in the engine compartment on the passenger side...
Just crawled all over the truck and I think I found the charcoal canister, but couldn't trace it back to the vent solenoid... There was something right next to the canister, but again, it looked nothing like the replacement part listed on Rock Auto...
I'm not too knowledgeable about wiring and electrical systems. I'm getting a P1451 code (EVAP Control System Canister Vent Solenoid Circuit Malfunction) on my 99 4.2. I've read that it could be a bad solenoid, bad wiring, or a blown fuse. So far I've;
- checked (and changed) the related fuse
- checked the wiring for damage at the connector
- checked voltage at the connector (12 volts)
- checked the resistance at the solenoid (around 60 ohms)
- actuated the solenoid with a 9V battery (can hear it opening and closing)
I haven't had a chance to check the wiring all the way back up the frame to yet, but I noticed that the ground at the trailer wiring harness has broken off the frame. Would this potentially cause a fault in the upstream wiring? I'm going to slap a new connector on and bolt it back down anyway, but as it's Labour (Labor) Day I'll have to wait for the stores to be open tomorrow.
Check engine light emissions evap system code comes up when the system is scanned what could be problem? 1998 chevrolet prizm...
View 4 RepliesI've been getting this code for a while. Changed the Purge solenoid and valve, replaced the hose from the canister to the two units, didn't change the hose to the intake.
Is there anything else to check? Could it be a bad gas cap? the one on the truck is a replacement.
My 2009 F250 5.4 was throwing code P0442 - minor EVAP control system leak.
The first time it happened, the guy at the parts store checked it out, reset it, and said if it comes back, try replacing the gas cap.
The second time it happened, same thing.
I bought a Stant cap at my local parts shop, and had them reset it again. I don't like the Stant cap since it does not fit the retainer correctly, but it sealed fine.
However, the same code came back.
It took a smoke test to identify a leak from the vent tube on top of the fuel tank. The tube was replaced today.
If the code stays gone for a few hundred miles, I'm going to switch back to the original gas cap. I want to make sure the leak is gone before I change anything.
I have a 2006 Hyundai Azera that is coming up with the error code P2422. I have figured out that the code relates to the EVAP system. I have cleared the code a few times but it always comes back within a few kilometers. Also I have started to notice at some gas stations that the gas stops pumping around every $5 i put in the tank. This only happens at some gas stations but not all that i go to.
View 3 Replies2009, 89K miles ... As title states, check engine light came on today and after the codes were pulled, I got P0496. It was referred to as "Large EVAP system detected". I'm guessing this may have something to do with the fuel vapor management system but not sure what's a sure bet to check.
View 6 RepliesIt all started with a fuel cap loose light (it wasn't) after a day or two the MIL came on and got this code I reset it but I'm sure it'll come back since there's probably a real leak. What can I check myself to find this leak?
View 11 RepliesNew owner of a 2003 1.8TPassat (29,000mi) as of the last 2 weeks and have just had my MIL come on. Scanned it at home with my Actron CP9125 scanner and got this code (P0455) which reads in the scanners manual as "EVAP Emission Control System Leak (Large)". Didn't know if this was a generic description of the code or VW has a more specific definition. What precisely this is in reference to, gas cap, vacuum hose????? Or what VW's actual description of this code is?
View 3 RepliesThis is the code i pulled from Vag. Its not the gas cap...
VCDS Release 805.0: Generic OBD2
Mode 03: Emission related fault codes
Address 10 (Engine): 1 Fault Found:
P0456 - EVAP System: Very Small Leak Detected
2004 VW touareg v6 - engine light on - autozone diagnosed as code P0456. Possibly gas cap, so I replaced with aftermarket gas cap from auto zone. Light still on. What can I do or replace to fix problem. I read something about a N60 or N80 valve. Is this something I can buy and replace myself. Most of my mechanical experience is related to working on a 85 CJ7 with an inline 6cyl or Chevy trucks. If the N valve is a easy fix, any instructions and pictures of how to do this.
View 1 RepliesI have a 1997 Ford Ranger and my Check Engine Light came on a while back. So I eventually bought a scan tool and I'm only getting one code which is P1443. I've looked at both my Chilton and Haynes Manuals, my Ranger manual itself which is pretty useless for this problem, and I've been searching the internet like crazy.
From the threads I have read here it doesn't seem like a hard problem to fix yourself, and it seems like if you take it in anywhere they will charge you an arm and a leg to work on the EVAP system but it's an affordable do it yourself project.
I just don't know where to begin though, I see people talking about buying the complete set with hoses and the canister and sensor all together but I can't find all these parts. Where do I begin to repair the EVAP system?
97 Aerostar 3.0. Factory A/C system staying on defrost. Going to check and replace as necessary all under hood vacuum lines as soon as it cools down. I can already see some cracks in the plastic lines.
But. Just in case, where is the actuator for the door that directs the air flow either to the dash vents or defroster vents etc? Is it the one I can see from under the hood or in some impossible location?
Just received a P0441 CEL (Evap Emission System Incorrect Purge Flow). I have a 2.7l engine, 2WD. I've read other forums and it seems it's most likely the purge valve or charcoal canister.
View 7 RepliesI've had the check engine light come on and was told it was probably from topping up too much and that it would go off on it's own... I should say I have no issues with idle or rough starts.
I had it scanned at Auto Zone. The print out shows: "EVAP emission system incorrect purge flow probable cause
1) Faulty purge control solenoid
2) Faulty vent solenoid
3) Blocked vapor canister
Previous posts suggest if it were a blocked vapor canister I'd have trouble completely filling the tank so I am hoping it's one of the others. Almost everything I see suggests the purge control and that looks like an easy fix. My concerns are a) if it is the vent solenoid - how hard is that to get at and b) what is the part number as I can't find it listed anywhere? I want to have both on hand before I start trying to fix this. Lastly if it is the vent solenoid should I just give up and see a dealer??
A few days ago code 0496 popped up for evap system problems. The fuel tank is very pressurized and there is a constant bubbling heard in the fuel in the tank with the gas cap removed. Sounds like blowing air through a drink with a straw. I have never had a problem like this with any car in over 45 years.
View 1 RepliesCEL came on after a couple of driving cycles showing code P0456 (evap emission control system very small leak detected)............. car drives fine has good gas mileage.....
View 13 Replies97 ranger 2.3l ... I have a problem where I'm losing full power (like cutting out) while under acceleration it's only for a split second almost like a hesitation. I got p1443 for the first time today and I was looking at my fuel trims and I noticed my long term FT is at 99.2% and never changes while my short term goes between negative and positive no more than 6%positive and like -4% I assume this is normal for short term but I really am just guessing on that. I am thinking perhaps I need a new fuel pump...but maybe I'm wrong...truck has a new fuel filter and a new evap purge solenoid...
View 14 Replies2001 X, Limited, 6.8L
Recently, when i turn my X completely off and remove the key, I hear something that sounds like it runs on and off. I popped the hood and it sounded like it was coming from the EVAP canister. It will engage several times, even while my vehicle is off. I am not sure if this problem is related but sometimes when I turn my key off and remove it, my air will still be running if the switch for the air isn't turned off. Could this be related and point to a bad ignition switch? Or is this a coincidence and my ignition switch is bad along with a whole other string of problems within my EVAP system?