Ford Aerostar :: 1996 - OD Light Blinking / Code P0500 Speed Sensor A Malfunction
Jul 27, 2013
Vehicle is a 1996 Aero* XLT, 4.0 engine with 155000+ miles. I'm getting the P0500 code with the OD light blinking. Tranny is not shifting properly. Did not look at the speedo or check the cruise due to worry about making it to my driveway. I have had ocasion to set the cruise to 45MPH and at times it will drop out. I don't know the lower limit on the cruise. Is this speed sensor the same as the VSS...
View 9 Replies
Advertisement
My car is now 24/7 with this error which is Vehicle Speed Sensor malfunction an there seems to be no way of solving it, symptoms are:
*Speedometer not working, needle always in 0
*Power steering not working
*Car wont past 3rd gear
*Check engine light and power steering light on
I checked all 4 speed sensors and the wiring looks good and they look good. Also if i hit a bump, issue goes away for a couple of minutes, until i hit another, etc, so looks like a wire or short circuit, cant tell. Is there a speed sensor on the transmission as well? where is located?
View 1 Replies
Recently, my I4 XLE camry with abs came up with a cel P0500 - Vehicle Speed Sensor A Malfunction. Where the vehicle speed sensor is located? i doubt this thing's hard to service, but so far i have no luck finding it.
View 13 Replies
So I'm getting code p0500 the question I have is will the speed sensor on the tail on my transmission cause this code on my 99 f150 4x4 . the reason I ask is because this sensor has been broken off . I'm hopeful it only control's my speedometer and is not related to the code . I've tried to remove what is left however in fear if I get it loose it may fall into the transmission. I will be replacing the speed sensor on the pumpkin this weekend . but the transmission it's the upper one is broke off below the surface of the transmission this is a manual transmission....
View 2 Replies
2010 RX350 check engine light is on code P0500 came up it said speed sensor A...
View 1 Replies
Where the vehicle speed sensor is located on the 2007 es350. Reomoved battery and air filter box but just can't find it.
View 1 Replies
I have an 08 avalon w/ 281k miles. NEED to replace the transmission speed sensor (P0500 code thrown). Where is it located on the trans and what is the part #? I'm thinking about servicing the trans while I'm there but looks like a lot of "comments" regarding this transmission and the problems with servicing it!?
View 9 Replies
I have read several of the post on here about speedo's acting up, but I'm not finding anything that pertains to my specific problem. A few months ago I bought a 2000 Excursion, it currently has around 179,000 miles on it. When I got it the ABS light was on and this site is actually where I found out to replace the sensor on the rear end to fix that. My problem is that until a few weeks ago even with the ABS light on my speedo worked just fine and then it started acting up every time I hit the brake pedal and then eventually quit working all together and my cruise control light would flash as well as the OD light.
I replaced the sensor in the rear end and also found out about a recall for the cruise control and had that repaired as well. Now the ABS light is no longer on and the cruise light is not flashing, however the OD light still flashes and 95% of the time my speedo does not work at all. On Monday while heading to town it started working, hit the brakes and all was good, set the cruise control and used it all the way to town, but as soon as I hit the brakes the needle started jumping around and went back to zero and stayed there. I have ohmed the sensors and wires from sensors to harness under the hood and all seems good. The only code I can pull with my meter is P0500 which is just a generic code.
View 6 Replies
So I have a 1996 Chevy Lumina (3.1L V6 engine) and I keep getting a DTC code P0101, which is a Mass Airflow Sensor malfunction. It's rather annoying because every time this happens, my engine shuts off. I'm talking no power steering, no power breaks, no acceleration, nothing. So I replaced the mass airflow sensor and it continues to stop about every five minutes. However, it does something odd and that is that the car drives just fine when it's in Overdrive and stops when it's in regular drive. I don't know if that's important, but I thought it might diagnose the problem.
View 4 Replies
Got an air bag code 41. Comes on and flashes the code a number of times, then goes off for the rest of the ride. It is a 96 Arerostar, XLT, 4LV6. From what I read it is a short someplace. Where are the crash sensors and how do you check them for "shorts"? I don't understand much about the whole system.
View 12 Replies
I've got a 99 F-250 6.8L V10 manual 4WD with no speedometer or odometer. The ABS and MIL lights are on. Code is P0500 - VSS malfunction.
This started when the previous owner hooked up some large LED backup lights to the factory wiring. Something smoked under the dash. He then moved them to a relay-switched +12V feed. He reported that the backup light fuse did not blow.
Ive tested the backup light fuse and the recently replaced VSS. Fuse is good and the VSS tests ok for Ohms and gives AC voltage when the tone ring turns. I pulled the fuse panel, GEM, and PCM. There's no visible damage anywhere there. I'm stumped. Tomorrow, I'll dig for any melted wiring under the dash....
View 8 Replies
I have a 2001 Toyota Celica GT, automatic with 177,000 miles, it has been very well maintained. I started having a problem usually just after starting when it is still not completely warmed up. I try and shift it into reverse or drive, and the shifter says it is in those gears, but the car acts like it is in neutral. Once it gets a little warmer I can try it again and it will slowly shift into reverse or drive, usually though the rpm's seem to go a little higher than normal while it shifts. It seems to drive pretty well after this, shifting-wise, but not exactly perfect.
When it is completely warm though it usually drives really well - mostly I do a lot of highway driving. The transmission fluid is full, and looks perfect, nothing in it, not burnt. Previous owner had it changed a few years ago I believe. The check engine light is on and the codes are Speed Sensor A P0500, P0770 Shift solenoid E. My speedometer also works perfectly by the way. I don't have a lot of good shops around and I feel like the ones that are closest to me will see dollar signs in their eyes when they see that transmission code and will just try and replace the whole transmission right off the bat.
View 1 Replies
97 ranger 2.3l 5spd ... I keep getting p0500 code. the speedometer and odometer work fine. I understand they get they're reading from the OSS on the transmission. Now I also have the vss in the axle housing which I believe is what gives the ultimate speed reading to the pcm that way there is no need to ever adjust for axle ratio.
When using the torque app with my obd reader my OBD MPH guage does nothing until I get to about 55 then it bounces around randomly between 20 and 55 and once I hit 60 mph it reads correctly. I have tried 3 different vss sensors checked wire continuity from sensor to firewall examined the teeth/sprocket that gives the vss it's reading and it all checks out...
My questions are:
- What volts or ohms are supposed to come out of the plug end so I can test if the signal to the sensor is working
- Looking for wiring schematics for this sensor to pcm...my schematic only has the oss.
View 6 Replies
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 Replies
I've got a 2000 ex limited with the v10.4x4. The engine light came on. So I had it scanned. Also the a.b.s light is on.and the overdrive off light was flashing but now isn't. The parts store that scanned it said code was po500. Told me it's a speed sensor but that there's 3 of them on the truck. Which sensor it is.
View 14 Replies
I just replaced my starter and on my first ride after replacing it the X started to stumble a bit, and then would stall out at almost every stop light. It threw a CE light and I pulled the code P0720. I searched here and it seems most guys say this is a C.O.P. issue. If it is a bad C.O.P. would it stall like that?
I did have the battery disconnected but I made sure the terminals were clean and tight. Is this a coincidence or did I do something while changing the starter?
View 8 Replies
I've got a 2006 F350 5.4L.
The ABS light came on and it was throwing a 'rear speed sensor' code. I searched around and it seemed to be a common issue that the sensor goes bad and needs to be replaced.
I bought a sensor and replaced it, but in doing so, I saw that while the sensor was indeed bad (cracked) the wire right at the connector was corroded.
I replaced the sensor but the ABS light is still on the dash. Is it possible that they code simply needs to be cleared? I was able to read it with my OBD2 dongle and Dash Command App, but maybe I'm not able to clear it?
Or is it more likely that the corroded wire on the connector is the issue? (it wasn't fully corroded and I cleaned it up and sealed it.). It didn't look like I could pull the wires out of the connector, so I assume I'll need a new connector. What is the part number?
View 2 Replies
1999 F250 Super Duty 6.8 V10 4x4 157k miles
On Friday afternoon the ABS light on my dash came up, ran the codes on my SCT Livewire and came up with a "P0500 Vehicle Speed Sensor A"
What should I be going after? Rear speed sensor? Front ABS sensors? Transmission speed sensor?
Speedometer is functioning 90% of the time, twice in the last 48 hours it wouldn't then shift hard and I would pull off to reset.
I have looked over the search results and wondered if there is a way to test the sensor with my multi-meter? Seems quite a bit of people had flashing over-drive light's at the same time, which I do not.
View 6 Replies
My 99 F250 with a V10 had an abs light come on and then it would go off. Now the ABS light stays on and it drove fine for a little while but the other night the Service Engine light came on along with the ABS light. Tranny was shifting harsh, winding out and I scanned the codes and got P0500. Is it the sensor on top of the rear differential or is it the ABS light causing the problem?
View 2 Replies
So yesterday I decided to wash my truck and after taking care of that I took it for a short drive and the tranny started acting funny. Check engine light comes on and the code is P0500 . It calls for a VSS but I cant locate it. Also the fact that it did after washing the truck is making me think its a wiring issue... F250 SD 5.4 4x4 ....
View 5 Replies
I have an ABS light on. I have crawled under the truck I don't know how many times everything is connected just as it should be. The wires did have to taped up because they burnt into after getting against the exhaust at some point, but I had fixed that awhile ago, I've even tore back into the tape and re-did everything again, nothing gets rid of the ABS light. When this first happened it would go away after I turned the truck off, but would come back after using the brakes a few times, especially harder stops. Then it got to where it just came on and stayed on, and didn't go out no matter what. Thinking my ABS speed sensor went, I bought a brand new motorcraft one from rock auto it fits perfectly in the rear, plug looks good. I can't find NOTHING that would keep this light on. The code is always the same "Rear ABS Center Speed Sensor Input Malfunction", how to get rid of this?
View 1 Replies
