1994 - 3.0 .... Back behind the water pump there is a stream of coolant what could that be. Water pump has been replaced earlier last year I thought that fixed it,there has always been a mystery leak..
View 6 RepliesThis is an update to my Heater Hose to Water Pump Failure post. As it turns out, the water/coolant pump seems to have failed at the same time as the heater hose. I think Ford secretly installed an internal time mechanism to deconstruct certain parts at the same time.
Anyway, in desperation I took the van to the local Ford dealer for an inspection. NOTE: I don't trust most of the locally owned small time shops and national franchises. Half of the time, they don't know what they are talking about.
They said the water pump is toast. And I already knew that! Then they said, because the water pump is attached to the front timing chain cover, they need to replace the gaskets there also, and also the oil pan is attached to the front chain cover, so that needs done, and then they said the radiator is also leaking. What!!!
Then they asked if I would be interested in buying a new or used vehicle. This tool works great. Mine happens to be a left hand fan. The tool is used with the handle on the left. This tool is used to hold Water Pump pulley stationary, while unbolting the fan assembly.
Tomorrow morning is when I finally replace the water pump. Not a lot of tool are needed, except for the stubborn fan clutch. Sockets: 8, 10, 13, 17, except a 22 mm open end wrench for the fan clutch.
My 92 Explorer 4WD has a coolant leak somewhere at the front of the engine above the water pump. I assume it's the lower intake manifold gasket leaking. The engine has 170k miles. I'm also seeing a small amount of white smoke, possibly steam when the engine is running. It's somewhat heavy when I start it up but mostly goes away once warm, so I suppose it could be steam, but could be coolant from either a head gasket leak or lower intake leak.
I also get a lot of water from the exhaust dripping on to the floor and the smell of the exhaust could be that of coolant, it's hard to tell. There is no coolant in the oil. I was wondering if I should go ahead and change the head gaskets while I have the intake out. Is there anyway to be certain the head gaskets are fine? I'd hate to change the intake gasket to find out there's a small leak in one of the head gaskets.
One other thing: I failed emissions because my CO was too high, but my HC and NOx were very low. Could this be an indication of coolant entering the combustion chamber? Just wondering why my CO was so high yet everything else passed (Massachusetts emissions).
Recently, I bought a new-to-me 1994 Jaguar XJ6 which had a small laundry list of things that needed work. Amongst them was to have the waterpump and belt replaced. Long story short, after getting it back from the shop (I'm a repeat customer) and 50 miles down the road, I checked things out under the hood. I saw that there was a small bit of coolant sitting on top of the pump where the mating surfaces meet. It appeared that was some weeping from the gasket. I'm a little perplexed because this shop hasn't done wrong by me before, but there's a first time for everything. Is it possible that the cold weather in North Dakota (routinely -10) is a factor? It doesn't appear to be a catastrophic leak by any means, but I intend to keep my eye on in it. In the mean time, I made sure the bolts nearest the leak were adequately tight and put some red RTV sealant where it was leaking. Is it possible this problem will "go away" or do I have to try to shake down the shop and get them to re-check it/fix it? Frankly, I'd rather not have to deal with them again, but I paid them good money to get it fixed.
View 6 RepliesNoticed about a gallon of coolant on my floor the last 4 days. Got it pressure tested and was told bad water pump. Had it changed with timing belt and tensioners. Got home, next day, same thing. Coolant everywhere. Also, do I really need to put G12++ in as coolant? I've been using it but the shop put some green stuff in it.
I have a 2005, V8, Phaeton with 181,000 miles. Also, my car overheated, got the coolant too hot warning, 270 on gauge, let it sit 5 minutes, no problem afterwards. Should the thermostat have been changed also?
One last issue with my 2000 B3000 3.0L. The leak seems to be on the left (passenger) side of the water pump very near where the bottom radiator hose connects to it. I can't find any loose bolts. It does not leak while driving the truck or soon after. It has to sit for several hours or overnight before it shows up. There are usually 3 or 4 wet spots where it drips from the water pump to the frame to the driveway. It is small enough that I only have to fill up my coolant tank every 1 or 2 months. Could this just be a small gasket leak? It's been happening for about a year or so I think. I replaced the radiator about 2 years ago. I've been expecting it to get worse or bust loose and have been checking it very often. I've never seen one not leak while running like this-has me puzzled.
View 6 RepliesSo I parked on an incline last night for ~an hour or so, and suddenly my coolant light came on and my reservoir was completely empty. Sure enough, all the coolant had leaked out of the car. I am sure it's the water pump, but it doesn't seem to be a complete failed one because I picked up and filled my car's reservoir back up today and it hasn't leaked at all.
My guess is the pump isn't bolted on right and on the incline, the gasket is breaking it's seal, or some oil dripped down onto it when on the incline and the gasket swelled.
Nonetheless, my dealership is covering it on Friday, and they said they finally are making them with metal housings instead of plastic, and recalls should be going out soon (win for the MKVI crowd).
So my coolant system woes have continued! I recently replaced my thermostat ,thermostat housing, thermostat cover and all of the rings and gaskets. I finally stopped the leak on the driver side which seem to be the thermostat now about seven days later I am experiencing leaking on the passenger side. I walked out from work today and noticed I pool of coolant under the car. I can't tell exactly where it's coming from but it's coming from one of the components that runs off of the large belt. I snapped a few pics from the bottom of the car I don't think this is the actual component that's leaking. I think the leak is just falling off of it . I was wondering where the water pump is located.
View 5 RepliesI was driving my 2005 RX 330 (138k miles) North on I-75 through Atlanta in rush hour traffic when the car completely died in the left hand lane w/ no shoulder. GDOT stopped six lanes of traffic to push us up and over a couple of hundred yards to a right shoulder. It was determined that due to a coolant leak from the water pump the timing belt malfunctioned and shredded.
I had heard that the water pump should be replaced during the 90k maintenance when the timing belt is changed, but my water pump was not replaced according to my maintenance records. I understand from reading a couple of posts that this isn't always required but that they do check the water pump. Is this correct? And if so should they have noticed that there was a potential problem?
I just wanted to share with you all about a coolant leakage problem I had experienced for a couple of days.
It all started a few days ago when I noticed the temperature gauge needle, which I hardly ever look at, began fluctuating in the hot region. I thought "oh my god" what is wrong? I then stopped at the nearest gas station and added some, I mean a lot, of water. My initial thought was the coolant level was too low.
The following day, I noticed the belts were squealing a bit (at that time I thought it was another vehicle with loose belts, but NO... it was mine making the belt noise). At that time, I did not realize it was because the coolant was leaking onto the belt(s). But then when I made a stop at a location for a couple of minutes, I returned to my Aerostar and noticed a trail of coolant leaking from underneath the vehicle.
I thought "oh my god" the water pump is busted! I then took it to a local repair shop and inquired about the cost to replace the water pump.
But after I inspected the vehicle more thoroughly, I noticed some dryed out green colored stuff where the heater hose connects to the water pump. I then removed the heater hose from the water pump and discovered to my surprise a tiny hole had developed where the hose is expanded from 5/8 to 3/4 inches.
My plan to repair the problem is to purchase about 6" of 3/4" heater hose (to connect it to the water pump), and a Gates or Dorman plastic adapter reduction fitting that reduces it to 5/8", in order to plug it into the factory original old heater hose.
This is an emergency repair. While inspecting the heater hose, I discovered an electrical connection that goes no where.
1989 3.0 shorty - 135K on her - and at 21 years old, the original radiator finally failed with a hair line crack, and so I bought a plastic on, from on of the part stores, put it in, and now it takes on like a gallon a month of antifreeze.
BUT I see no leak at all... the engine runs fine, and not head gasket or crack head (been there done that with the explorer I have). I don't smell it either really -heater core is dry... as is floor underneath. Need replacing the Radiator?
89 3.0L - I seem to loose a little bit of coolant every time I drive maybe like 1/2 a pint?
I checked every connection - engine running, and even waited to make sure the t-stat was opening, and closed, etc (maybe it was the top hose, nope)
I did replace the radiator a couple of years ago, and had the problem ever since I did that, but at the same time, I also replaced the T-Stat with a 165 degree, since she was starting to run a bit on the hot side, even with the new water pump and radiator I did... on a cool day, it would run at the middle of the gauge with a 190 degree... and with AC on, hills and 95 degree days, it would be pushing upwards of 3/4 of the way on the gauge...
Could the 165 degree therm stat be somehow causing a 13 lb cap to not function properly? I replaced the original with a Stant... but Im thinking I should get a new Motorcraft OEM cap, since the other one lasted 20 years!
I kept the old radiator - love it - "wow real brass/copper in there!" it was still fine when I pulled it, but had a hairline crack right below the top hose area...
Anyways, pressure tests revel nothing, I see no bubbles or anything with the engine idling, cap off
I replaced the water pump on my 3.0 and now, 9 months later, there is a coolant leak from the front engine cover (timing chain cover). The leak has probably been there two months or so, but it was so small initially, it was difficult to locate. A google search seems to indicate that a leak from the timing cover is somewhat common on the 3.0.
When I was doing the job, I noticed that some of the water pump bolts also hold the front cover in place, which seems like a bad design because removing those bolts takes some of the compression off of the timing cover gasket. Now that I have this leak, I'm wondering if changing the water pump is related to the leak. And, yes, I did use thread sealant on the bolts as recommended in the genuine Ford shop manual.
So now, I'm curious. Noticed a leak from the timing cover relatively soon after replacing the water pump on 3.0?
the only thing that is left to replace would be the radiator?my truck is a 1994 f150 and it is not overheating!i get lukewarm heat only on the highway,everywhere else it is cold air!!this new england weather is killing me
View 10 RepliesI'm feeling a bit embarrassed posting my delima, but I have a minor coolant leak which seams to be coming from where the heater hoses connect to the water pump and as well to the thermostat nuckle thingy. I have replaced all of the hose fittings with SS band clamps.
A couple of weeks ago I replaced the water pump, thermostat, alternator, rad hoses, belts, coolant sensor, PS tension pulley. The water pump is now tight and sealed. Since then the temperature gauge has been continually fluctuating from Normal to near Cold.
I was wondering if I should have placed some type of sealant compound where the heater hoses connect to the water pump and also to the thermostat nuckle thingy.
Initially, I thought it may be residual trapped air in the coolant system. But after a week, it became apparent that the heater hoses were leaking at the engine, and at the water pump, connections.
What puzzles and torments me is why is the temperature gauge fluctuating so widely up and down? This is totally weird.
I was surprised by a leak and identified where the water was coming from, the bottom of my vehicle. It's from a gasket or seal on the front of the pan near the flywheel. 1994 Ford Explorer 4X4.
View 6 RepliesI seem to have a coolant leak somewhere - i changed the oil yesterday and while i was at it i topped off the coolant in the recovery tank to the cold line. Took the truck out for about a half hour then parked it over night. when i came out this morning i found a pretty sizable puddle on the ground, seeming to originate from the drivers side, and when i checked the radiator it was low but the coolant recovery tank was full past the cold line...i let idle today for about a half hour then let it cool down trying to catch it in the act but saw nothing. if i trace the source of the puddle it seems to be coming from the cap area or at least that side of the compartment. would this be the radiator cap itself? allowing coolant to boil over and out but not get sucked back in? Since I've had the truck i have noticed a small, very small, amount of coolant on the ground now and again but this is the first big puddle.
View 1 Replies1995 Ford Van E150. So I've been trying to solve my overheating problem for months now. One morning I walked out of my house and all of my coolants was on the street. I could not completely detect the source of the leak after running more coolant through it. I also checked the dip stick and coolant on the ground for any sign of oil/coolant mixing. I started by replacing the thermostat.
I did a more thorough inspection and found a crack at the bottom of the radiator that I replaced less than two years ago. I replaced the radiator again and while I had the belt, intake and fan disassembled I switched out the water pump as well. The old water pump was gunked and the gasket was almost completely worn off. The van is still overheating and spitting out coolant at a much higher rate. I'm guessing because of the new water pump. A friend said it could be the intake manifold because of where the steam was coming from the motor.
I replaced my water pump on my 2000 Excursion 7.3 about six months ago because it was leaking from the little hole underneath. Everything was fine until today I noticed a big stain on my driveway under the front of the truck. I took a look and the new pump is leaking. It seems to be coming from the the back of the water pump where it sits flush against the engine.
Could the gasket have deteriorated or cracked? I bough it from a local parts store called part source, so it should be under warranty. Any thoughts?
I noticed green coolant leaking from bottom of black, what I think is called, timing belt cover. There is 188, 000 miles, and when I changed the timing belt, I did not change the water pump, although I did change out the thermostat. I have done a lot of work on this truck in the past. I checked the oil and no signs of water or coolant mixed in. The water pump is not weeping from the top well. I rely on this truck and the way I look at it is I may just keep driving it until it goes kaput (its real beat up). Should I go to an auto parts store and see if I can buy some sealant. I would guess it is either the water pump or maybe the timing cover gasket? I have inspected all hoses, and I see nothing. The leak must be coming from somewhere under that black, plastic cover. I am capable and willing to do just about anything other than perhaps a full engine pull, although I have the wherewithal to do that too if absolutely necessary.
View 9 RepliesI replaced a water pump on a customers 2013 5.0L truck this week. The bearing was totally shot and lost all the coolant. Truck only had 46000 miles on it, is this common?
View 7 Replies