Was driving issue free most of day, when leaving a red light I noticed my i had to give the van some extra gas to get up and go, then i could feel the brakes getting tighter and tighter to the point where I had to park the van. So currently my van is sitting in a parking lot 30 miles from home with locked up front brakes. Both driver and passenger front wheels were hot to the touch.
View 11 RepliesWhat would cause the front wheel on drivers side to lock up if it isn't the brakes. have been hearing a loud popping noise for a while on drivers side especially when turning left. Today got really loud just driving and then a real loud grinding noise. Then a loud pop and front wheel locked up and skidded across highway til i came to a stop. What it could be or how can i at least get wheel to turn to get it on trailer...
View 6 RepliesWhen braking from very low speed to full stop (f.e. parking maneuvers), i often hear a loud "pop" coming from the front brakes, regardless of steering direction. I'm pretty sure this has been discussed before here but can't find a thread.
Brakes are otherwise working good (front & rear) but it's time to do a maintenance just to be safe.
97' XLT RWD, 3.0L Vulcan, 99890miles - can't wait to see turning over to 100'000.. hope, i do not miss the moment
Going down a steep loose gravel drive way, going maybe 5 miles per hour. About 50 feet before the stop sign we lightly applied the brakes and the front right wheel completely locked up. If we didn't turn into the grass we would of stopped in the middle of the busy street. We picked up speed when we applied the brakes, like we were on ice. When I got out, I could see the one long brake mark in the driveway. This happened on a paved road about 6 months ago, it had some loose gravel at the stop sign. I couldn't tell which wheel locked up at the time. This happened on snow in December to, twice. Since the ABS light never came on. Brake pads and rotors needed replacing about 9 months ago. Tires have been rotated, no change. Not sure what it could be. I disconnected the Abs fuse for now.
View 5 RepliesI have a 1997 Aerostar 4.0L 165k Miles Keyless entry
I am having strange electrical problems. This happens on an unpredictable basis but is getting more frequent (ie. use to be once every couple days and now is happening several times during my 24 mile drive to or from work).
After starting, the car door locks may automatically lock; however, a few seconds later they may lock again, and again.... This may happen 5-10 times in a row then it stops for 5 minutes or 2 days.
This week a new symptom showed up. The dome light came on while driving. It stayed on for a few seconds then went off. 5 seconds later the doors locked. This may or may not repeat. The light may stay on for 5 or 30 seconds always followed by the doors locking. It may repeat once or sever times in a row. I also noticed if I stepped on the brakes it turned off the dome light and then the doors locked but then it would likely start again. Turning on the headlights did not seem to have any effect.
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
My 94 is on the mend , since I got it a few months ago. The air conditioner blows cool , just not cold . It's still a R12 system, and I got the fittings/R134a/oil charge/and mineral spirits to do the change over, but hesitated when I found someone locally had a few cans of R12 for sale . My thought is to buy 1 can , and see if a shot would make the difference before going through the procedure to flush the 12 out and go with the 134a .
My biggest problem is lack of a gauge set , but a guy from CraigsList here says he walk me through the change over for 60 , and betting he'd have the hoses for a 12 system to hit that if that's how I decide to try first. I just wonder why , since I got it , the "cool" it does blow hasn't changed so I am betting it isn't leaking , but the jackleg I got it from was one that IMHO wouldn't know how to open the hood , or what to leave alone, I am just at that point of impasse, as to which way to go ...
It is a garage queen 1994 4.0 AWD with 42,000 miles in nearly perfect shape. Except for the dent in the rear on the passenger side.
I have posted a picture of the dash when going down the road. As you see the engine light is on. It comes on intermittently, pulled the codes, indicated MAF, 02 sensor, running lean/rich. Runs like a champ, no hesitation, still gets up and goes, gets the appropriate gas mileage. I replaced the 02 sensor with the original Ford Part. Didn't cause the engine light to stop going on after about 20 to 60 minutes driving, sometimes it doesn't come on at all.
Could this thermostat be running too cool and causing the engine to throw those codes? Would gladly take it to a mechanic, but seems like it might be a fishing trip with my dollars for them. Next I was going to replace the MAS myself, easily done with the original remanufactured part at a cost of 150.00, 70 for the core, but don't want to chase my tail with these engine lights on when it runs nearly perfect.
Have sprayed the MAF. Checked for air leaks anywhere. Done all the things I could do by just lifting the hood.
So the picture shows the Temp gauge barely touching the N flying down the road at 70 on a level surface, outside temp about 60. Reading the posts says they all run in the cool section of the temp gauge.
So the question is, do they run this cool? Heater works fine and the gauge goes up past the N resting before the O when going up hills on the way to Tahoe. Is this a thermostat problem on a 20 year vehicle with low mileage, or am I going to have to bite the bullet and let the mechanic go wandering through the vehicle?
1994 - 3.0 .... Back behind the water pump there is a stream of coolant what could that be. Water pump has been replaced earlier last year I thought that fixed it,there has always been a mystery leak..
View 6 Replies2 or 3 years ago my airbag light started blinking. 120,000 miles, only owner. The code changes daily. Then the car started reviving at highway speeds. Then cruise control wasn't reliable. Sometimes when I hit a bump, the cruise goes off. My mechanic said the reviving felt like it was going in and out of overdrive, so he rebuilt the transmission. No change. This past month, the car started to pull to the right. It felt like I was driving with the brake on, couldn't get up a small hill. Before I could get the car home, the brakes went to the floor and the car stalled. I had it towed to mechanic.
After 10 days, he couldn't duplicate problem, so I took the car back. A few days later, after 4 hours of errands in the hot Texas sun, it did it again for me. Pulled to the right, driving with the brake on feel, brakes to the floor. This time it smelled like something was burning, either brakes, belt or something, and the rear ABS light came on for the first time. Latest mechanic says it is probably a brake booster, but that doesn't explain the reviving does it? I've had it to 2 dealers, 3 mechanics, and no one has a clue what to check apparently. I am a senior, so I can't really start replacing everything. What should I tell them to check, and in what order? I love my Aerostar....
Srange noises of my 1994 AWD. When driving, if I take off fast, it makes a lot of pop noise, but if I take off slowly, then It's Ok. Or when I make a quick acceleration after slowing down then it make noise, but if I take it fairly slow then it's OK. The frequency is getting worse. My front axles are in good condition (30K miles on a rebuilt pair). I have unplugged the AWD controller box, it didn't do any difference. All gear shipped OK. So what is that noise in that condition? My 94 AWD is about 110k miles, good shocks.
View 14 RepliesAbout two years ago I sold my 1994 Aero (transmission was going, and other stuff) and bought a 1997 that was in much better shape. But one flaw it has is that it was used somewhere with high corrosion, so a lot of stuff is stuck or rusty. I haven't changed the rear bulbs since I got it, but this week, 2 out of three bulbs went. Actually, I only noticed the 2nd one because the blinker went too, and started blinking fast. The 3rd Brake light on top might have been out a while already.
Anyway, to my frustration, I cannot open the 3rd Brake Light to change the bulbs. Even after I removed the 2 screws, the lens won't budge. I tried gentle prying, but I can hear the plastic starting to crack. I figure there are 2 possibilities.
a) It somehow got fused to the gasket over time. or
b) It was crazy-glued shut by some insane maniac (a long-shot?). In which case I can try Acetone.
For starters, once the screws are removed, does just the red lens come out, or does the black frame around it come out with it? I tried prying on both, but one of them is surely wrong. Worst case scenario is that I break it, and have to glue it back on or get another one from a junk yard. But that is not good... Meanwhile I am living ok with just 2 brake lights.
My 1994 Aerostar, with 100,000 miles on it, started lurching at highway speeds. Weeks before this, the airbag light began blinking. The transmission man said it felt like it was shifting into overdrive, then out, then into overdrive, then out, etc.,etc. About this time, the cruise control quit being reliable. Dealership said codes didn't show a problem, "I must be mistaken". Then they said it sounded like a fuel filter.
View 6 RepliesI just bought a 94 Anniversary Edition that came with an aftermarket remote start. I upgraded the module so I could get better range and would like to connect the rear window defrost to it. I have the trunk release feature on the module and since it isn't in use figured I could use that function for the defrost. The module has a negative output. What wire in the defrost switch would I connect to and would I need a relay to convert the negative pulse to positive? The winters here get extremely cold.
View 3 RepliesStarting a hot engine in my 94 3.0L RWD occasionally produces a low- pitch 'wah-wah-wah' groaning noise that goes away after 3-4 seconds. It sounds like it's coming from the engine itself and what I'm hearing is an engine running without sufficient oil. It has never happened on cold starts, but about 30-40% of the time when restarting, like at a gas station after fill up, etc. I live in sunny San Diego so I put 10W40 in at the last oil change. It's also currently overfilled by about a quart--I intend to remedy, but have not gotten around to it yet. Could it be the viscosity or quantity of oil? It's a real sphincter puckerer of a sound and I want to get it resolved.
View 2 RepliesLooking for the fuse that controls the overdrive torque converter clutch/lock up/engagement. Had a look in the owner's manual, didn't find anything. Pulled a couple fuses that I thought might be the one, no go.
I had found this fuse b4 but now a couple years later can't remember which one it is and can't remember where I found the info on what # the fuse was.
I easily removed the key lock cylinder but when I went to put the new one in I cannot get it to turn all the way back to lock the pin in place. The steering wheel is not in the locked position nor can I get it to lock. I have turned the steering wheel as far left and right as I could go with no success on getting it to lock or on getting the ignition key lock cylinder to turn back securing the actuator pin. The old key lock cylinder won't go back in either. What am I doing wrong?
View 3 RepliesI just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
When I hit the brakes hard like seating the brakes the Aero would stall....
View 12 RepliesMy '93 has the RABS lite on when I use the brakes and the brake light comes on when I use the brakes hard. While searching the topic I stumbled on a reference to bypassing theRABS with a piece of brake line, Looking for the particulars on this?
View 10 RepliesMy wife's 89 Aerostar is leaking brake fluid from the back side of what is either the distribution block or combination valve. I am not sure which it is but it is the first block you run into following the lines from the master cylinder and it is right below it near the fender well.
The part has been discontinued and is too expensive anyway so I am looking for input as to what this peice is and if / how to rebuild it.