Ford Aerostar :: 1994 - 3rd Brake Light Stuck On - Can't Change Bulbs
Feb 8, 2011
About two years ago I sold my 1994 Aero (transmission was going, and other stuff) and bought a 1997 that was in much better shape. But one flaw it has is that it was used somewhere with high corrosion, so a lot of stuff is stuck or rusty. I haven't changed the rear bulbs since I got it, but this week, 2 out of three bulbs went. Actually, I only noticed the 2nd one because the blinker went too, and started blinking fast. The 3rd Brake light on top might have been out a while already.
Anyway, to my frustration, I cannot open the 3rd Brake Light to change the bulbs. Even after I removed the 2 screws, the lens won't budge. I tried gentle prying, but I can hear the plastic starting to crack. I figure there are 2 possibilities.
a) It somehow got fused to the gasket over time. or
b) It was crazy-glued shut by some insane maniac (a long-shot?). In which case I can try Acetone.
For starters, once the screws are removed, does just the red lens come out, or does the black frame around it come out with it? I tried prying on both, but one of them is surely wrong. Worst case scenario is that I break it, and have to glue it back on or get another one from a junk yard. But that is not good... Meanwhile I am living ok with just 2 brake lights.
View 5 Replies
Advertisement
96 Aerostar Cargo 6 cyln. Auto.
There is a noise coming from what sounds like the rear passenger side wheel. Also, when you put it in drive and release your foot from the brake the van stays still. You have to push the gas to get it moving, like the brake is holding it. If you are going very slow on a flat surface the van will eventually stop instead of idling forward.
I have removed the wheel, it does turn hard. Pulled the drum (was very hard to remove). Had to move adjuster to remove drum. Cleaned inside, inspected the brake shoes, put drum back on, etc. I am pretty sure that brake is causing resistance. How to resolve it?
View 7 Replies
2 or 3 years ago my airbag light started blinking. 120,000 miles, only owner. The code changes daily. Then the car started reviving at highway speeds. Then cruise control wasn't reliable. Sometimes when I hit a bump, the cruise goes off. My mechanic said the reviving felt like it was going in and out of overdrive, so he rebuilt the transmission. No change. This past month, the car started to pull to the right. It felt like I was driving with the brake on, couldn't get up a small hill. Before I could get the car home, the brakes went to the floor and the car stalled. I had it towed to mechanic.
After 10 days, he couldn't duplicate problem, so I took the car back. A few days later, after 4 hours of errands in the hot Texas sun, it did it again for me. Pulled to the right, driving with the brake on feel, brakes to the floor. This time it smelled like something was burning, either brakes, belt or something, and the rear ABS light came on for the first time. Latest mechanic says it is probably a brake booster, but that doesn't explain the reviving does it? I've had it to 2 dealers, 3 mechanics, and no one has a clue what to check apparently. I am a senior, so I can't really start replacing everything. What should I tell them to check, and in what order? I love my Aerostar....
View 14 Replies
How do I change fog light bulbs on my prius 2011???
View 2 Replies
How to change the HID light bulbs? Looking for links with photos.
View 5 Replies
Any tricks that will make this job easier? They seem buried and when I reach I am only guessing as to what I am pulling out. For example, I pulled out a round cover, but what was it covering up? Must the bulb be twisted and then pulled or just pulled?
View 7 Replies
I'm having problems changing the interior lights for my prius. In particular the 3 personal lights at the front. how to change the light bulbs and what light bulbs they are?
View 13 Replies
I replaced all the exterior bulbs in my 2013 F250 6.7L with LED bulbs. My trailer lights work but brake and signals don't work on the trailer.
View 5 Replies
Was looking to change them out. But can't find anything on how hard/easy this is to do.
View 4 Replies
ok, just started to use my vag and now im stuck on trying to change my blinkers from 3 to 4 clicks and releasing to parking brake
View 1 Replies
I have a '95 Aerostar where the two lights are always on. I'd like to pull the codes if i can. Does this year has the RABS or the RABS II module. Or is the diagnostic connector the same?
View 14 Replies
Trying to replace the burnt bulbs. Did the obvious: removed the two screws but in no way could I take the red lens off. I pried hard almost broke it but it's not coming off. It feels like some other mechanism holding it down. It is the one on top of the lift gate. The inside is just a hole with wires going through. What's the trick?
View 12 Replies
I have a 2002 Subaru Outback. The rear right brake light housing cracked, and filled up with water, shorting the bulbs. I thought I was clever in taking the light unit off, draining the water, changing the bulbs, and caulking the crack with silicon. This worked for a while, then the battery died. I couldn't really figure out why - it was a year old, and had no prior issues starting the car. I swapped out the battery for a brand new one, and that seemed to solve the issue for a week. Then the car refused to start all over again. I remembered the brake light, checked it - filled again. So I replaced the unit and the pig electric line, and charge the battery. This seemed to solve the problem, but then the car failed to start after about 3 weeks.
One additional detail is the dial light switch on the driving shaft. One is able to turn this to adjust light settings. Regardless of position, the lights turn off when I turn off the car. However, failure to start seems to be additionally related to the position of this switch; if it's switched all the way back towards the driver the car appears to start consistently for weeks on end, BUT the tail lights fail to turn on in this position (though the brake lights work). Alternatively, dialing the switch all the way away from the driver turns on the tail lights, but seems to be related to battery drain.
I've checked the health of the battery and the contacts - everything checks out. At this point I'm wondering if it's an electrical fault or the alternator.
View 1 Replies
My 94 is on the mend , since I got it a few months ago. The air conditioner blows cool , just not cold . It's still a R12 system, and I got the fittings/R134a/oil charge/and mineral spirits to do the change over, but hesitated when I found someone locally had a few cans of R12 for sale . My thought is to buy 1 can , and see if a shot would make the difference before going through the procedure to flush the 12 out and go with the 134a .
My biggest problem is lack of a gauge set , but a guy from CraigsList here says he walk me through the change over for 60 , and betting he'd have the hoses for a 12 system to hit that if that's how I decide to try first. I just wonder why , since I got it , the "cool" it does blow hasn't changed so I am betting it isn't leaking , but the jackleg I got it from was one that IMHO wouldn't know how to open the hood , or what to leave alone, I am just at that point of impasse, as to which way to go ...
View 6 Replies
It is a garage queen 1994 4.0 AWD with 42,000 miles in nearly perfect shape. Except for the dent in the rear on the passenger side.
I have posted a picture of the dash when going down the road. As you see the engine light is on. It comes on intermittently, pulled the codes, indicated MAF, 02 sensor, running lean/rich. Runs like a champ, no hesitation, still gets up and goes, gets the appropriate gas mileage. I replaced the 02 sensor with the original Ford Part. Didn't cause the engine light to stop going on after about 20 to 60 minutes driving, sometimes it doesn't come on at all.
Could this thermostat be running too cool and causing the engine to throw those codes? Would gladly take it to a mechanic, but seems like it might be a fishing trip with my dollars for them. Next I was going to replace the MAS myself, easily done with the original remanufactured part at a cost of 150.00, 70 for the core, but don't want to chase my tail with these engine lights on when it runs nearly perfect.
Have sprayed the MAF. Checked for air leaks anywhere. Done all the things I could do by just lifting the hood.
So the picture shows the Temp gauge barely touching the N flying down the road at 70 on a level surface, outside temp about 60. Reading the posts says they all run in the cool section of the temp gauge.
So the question is, do they run this cool? Heater works fine and the gauge goes up past the N resting before the O when going up hills on the way to Tahoe. Is this a thermostat problem on a 20 year vehicle with low mileage, or am I going to have to bite the bullet and let the mechanic go wandering through the vehicle?
View 14 Replies
Was driving issue free most of day, when leaving a red light I noticed my i had to give the van some extra gas to get up and go, then i could feel the brakes getting tighter and tighter to the point where I had to park the van. So currently my van is sitting in a parking lot 30 miles from home with locked up front brakes. Both driver and passenger front wheels were hot to the touch.
View 11 Replies
Changing 3rd brake light to an led? Im doing the led swap on all the exterior lighting but I can't seem to find a red 3rd brake light. Using the f250 3rd brake light? Is it a direct swap?
View 14 Replies
Is there a DIY on how to change the headlamp bulbs, DRL and turn bulbs? Do i need to remove the bumper cover and/or headlamp from the car or can i change the bulbs with the headlamp in place?
View 3 Replies
1994 - 3.0 .... Back behind the water pump there is a stream of coolant what could that be. Water pump has been replaced earlier last year I thought that fixed it,there has always been a mystery leak..
View 6 Replies
How to change license plate bulbs? The little clear covers dont seem to pop off ........
View 3 Replies
Srange noises of my 1994 AWD. When driving, if I take off fast, it makes a lot of pop noise, but if I take off slowly, then It's Ok. Or when I make a quick acceleration after slowing down then it make noise, but if I take it fairly slow then it's OK. The frequency is getting worse. My front axles are in good condition (30K miles on a rebuilt pair). I have unplugged the AWD controller box, it didn't do any difference. All gear shipped OK. So what is that noise in that condition? My 94 AWD is about 110k miles, good shocks.
View 14 Replies
