Ford Aerostar :: 1993 - Gear Shifter Broke?
Feb 5, 2011
I went to put the van in park, and the gear shifter just went all floppy in my hand. I was able to wiggle/jostle it around and get it into neutral or drive, but nothing else. Tow truck driver crawled under the van, and put it into drive for me, and told me it was probably just going to need a new cable or link shaft (tube shaped thing)... My hubby usually fixes these things, but is now living 1700 miles away.
Anyway, the shop called me and said I needed a new steering column, and said something about the 'lower' cap or half??? He quoted me $340 for the job. I am not getting the connection between the gear shifter being loose/floppy and the steering column needing to be replaced? Is this right?
It is a 1993 Aerostar, 3.0 by the way...
View 14 Replies
Advertisement
My mom's 95 shifter is slowly getting worse. Right now it's at the point where we have to hunt for gears just to put it into park or reverse or d/od. It's not stiff like the rest of ours, hers is all sloppy and loose. She says it's been doing this for a while, but i think it got worse when i pulled her cluster out to change the light bulbs. I say this because i couldn't get the needle cable un done, so i just let the cluster rest on it while i was changing the bulbs, which put a little bit of tension on it.
View 14 Replies
Checked icm and is good, replaced coil and still no spark. Issues be gan when about 700 miles ago rotor button broke while driving??? Replaced button cap wires and plugs. Engine fired right up. Ran 700 miles and rotor button broke for 2nd time. This time replaced and will turn over but not crank. That's when I checked icm and changed coil. what should i check now?? 1993 Ranger 3.0 ... Truck has 199,800 miles. Top end was redone at 140,000.
View 10 Replies
I drove our 95 3.0l aero to work today, I was going to a job 45 miles away. It sounded like it was revving awfully high for 65-70mph, but the gear selecter said od, so I figured I was just crazy. Got to the job and tried to back up and the shifter wouldn't go into reverse. Parked for the day after realizing the shifter would go N and down, but not into rev or park. Apparently it was revving high, as the gear indicator was now off and I was no doubt in drive, driving to work. I got it home, then had to drop my daughter at work, by staying in OD.
Then on the way home the van just DIES while going 35+- mph. Won't restart, smelled gas after many many attempts to start. Towed home. NO spark. I have 12+ volts at+coil. I tried my ignition module and a new one, neither sparked at the coil wire. I bought a new coil, then checked resistance at + &-, and - and coil output post. Basically same resistance new & old coil. Did my hall effects or cam, or crank sensor just go out or? Why both problems same day? I thought if it was the coil or ignition module, maybe it got too warm on drive revving high. Does a 95 3.0 coil get triggered by the distrib haal effects or does the crank sensor do it?
I can easily see one of those being bad as they are original, with 334,000+ miles. All the tune up, coil, wires, plugs, ign module, cap, rotor, were replaced 55,000 miles ago. ALSO does this distrib have a TFI module on it? My book says to pull the distrib and remove it, like my 5.0l Mustang, but I don't see one, I think thats the ignition module on the pass. inner fender. I'd like to see if I can get 400,000 miles out of it.
View 4 Replies
We have a question about our 93 Aerostar. The A/C is working, but not very well. Not cold enough. It is fully charged. We are not able to see any condensation dripping below the car when parked, after running the air. We cannot discover where this condensation is going, or even wbere the hose from the evaporator is supposed to be. Shouldn't it be coming down into the front wheel well area? We have had the van since about 03, and the AC system has been replaced in that time. When the weather is cool (not often this summer) the air works OK, but it isn't keeping up in hot weather.
View 4 Replies
Is it possible to convert a 1993 2WD Aerostar EB with a A4LD to a AWD drivetrain? I am a Subaru veteran (this is my first time posting), and the mod capabilities of soobs is endless - older 2wd car to AWD is not hard at all on those cars - in fact it is a relatively easy bolt-in change.
Traction on snow (or anything else) in a stock 2WD Aerostar leaves MUCH to be desired (especially when compared to a vintage soob). How good is the AWD drivetrain overall? Is it as reliable and rugged as the 2WD? Gas mileage difference between 2wd and AWD? Handling? Maintenance? Are there different versions of the AWD? If so what are they like? I have a 1993 FSM for the drivetrain, but I don't know how similar other model years are.
View 14 Replies
I have an '86 Aerostar with the 2.3 four and 5-speed stick. The shifter is sloppy, and it's often hard to find 4th when downshifting from 5th, and sometimes, it shifts hard through all the gears. Other times, it works fine. The manual says that this shifter was used from 86 to 89 only. Did they use the same one on Rangers? Can I buy a rebuild kit? Or, is this a sign of some other problem such as the clutch slave cylinder?
View 1 Replies
Well I've got an nice steady leak coming from the front of the pan.... running aft of course (downhill, windflow). She's down right now for an AC overhaul and new PS pump/hoses, but I'm inspecting to see what is next to get this stinking oil leakage stopped.
Front HB removal and seal of course, done in situ (in position). But if it is actually the oil pan/seal, can that be done there also? Front of the pan looks tight to the crossmember, and how the internals look (tray baffles, pump pickup) I've no clue if it will come off. Once she is back up and running I'll ascertain where this leak originates.
Interweb searches show the 90-94 4.0L engine is notorious for pan gasket leaks. None of the writeups I've found thus far determine if that pan can be pulled where she sits.
View 4 Replies
I got this code and symptoms of 1-2 hard shift and no torque converter lockup. No flashing overdrive light on shifter. If I switch off engine all shifts are smooth until I pass 45mph. I would feel the TCC lockup. This doesn't happen the as i come to a stop I get a harsh 2-1 shift. Key off restart then shifts smoothly up and down provided I dont exceed the TCC lockup speed. This leads me to the TCC solenoid I think. Fluid has been changed regularly.
Had to drive 300 miles to get home. Only for the plate trans cooler the fluid would have overheated as on inclines on cruise control the engine would rev to 3k to keep the speed at 70mph and I could see the fluid temp increasing. Fuel consumption was very bad almost a full tank (with no ac). Doing some research there is talk about valve gasket blowout Epc solenoids etc, though these were for Rangers and Explorers, no real mention of Aerostar.
View 14 Replies
My Aerostar is a 93 extended EB with 4.0, AT, 212k mostly reliable miles, and blue and gold paint that has held up remarkably well. When started it runs great; smooth idle, easy revs, normal as can be. But when that third pip on the digital temp gauge hits Normal the van becomes possessed. The idle will randomly drop or surge or return to normal, the check engine light will come on for a few seconds then go off, all without pattern, just kinda crazy. Today I held it at 2k rpm, then it bogged down to like 800 rpm and lit the CEL, then it returned to 2k rpm and the light cleared, swung up to 2.5k, all while I hold the throttle steady. The light does not always come on when it bogs. I see no black smoke from the exhaust and it smells normal, but it was kinda windy today.
The check engine light is not lit otherwise so I assume no hard codes are stored. I think I found the code retrieval process for the OBDI but I have not done that yet. After reading a bit in this forum I thought to clean the MAP sensor, but I do not have security torx bits to remove it yet. As background a few years ago it had an oil leak from the top rear which I ignored, and it slowly rotted a harness back there till one day the harness died leaving me running on 3 cylinders. My local Speedy Lube guy was ex Ford dealership and knew Aerostars, he did the diagnosis and repair and said it was a common problem. But he has moved on. I was also told I have a torn boot on a plug wire, but there's no way to get my ham-like paws back in there, from front or back, to verify or replace. I mention all this as background, I doubt a bad plug wire is the issue here.
It seems like an odd problem to me because the only pattern is related to operating temp. It is not a constant problem, not an intermittent glitch, but it very definitely goes nuts right when it achieves normal temp. Aside from pulling the codes, which I will figure out tomorrow, any other tests I can run to diagnosis? Any way I can trick this thing into thinking it is cold all the time?
View 8 Replies
My 1993 ford aerostar 3.0 is a great vehicle but recently its been killing me trying to figure out what the cause is. I'll start at the beginning. I had a job over the hill in Westwood Ca. Ran low on gas on the way home. Too low apparently. Since i refueled it has a really rough idle and no power under acceleration. After it gets warmed up i get a bad smell of gas and exhaust in the cab.
Now if i turn it off wait 15 min or 12 hours it will run ok for 2 min then back to hell. I has not stalled and i have replaced the fuel filter and a few months back i cleaned the Mass air flow sensor and replaced the TPS. I would love to take it to a mechanic but as i have been living in this old girl for the passed 6 months money is non-existent.
What to do. I have even tried disconnecting 1 at a time... the TPS, MAF, and the 02 sensor. No difference. There has been no check engine light until I tested by disconnecting TPS etc.
View 8 Replies
I have a 1993 Aerostar 3.0L, automatic. The transmission has started dropping out of overdrive into drive while at speed. It's very inconsistent as sometimes it will drive without incident and sometimes it will barely go into overdrive and then drop back out and remain in drive for an extend period of time. I changed the fluid/filter/gasket thinking it was just overdue for changing but no luck. The fluid level is fine, perhaps even a little high. Fluid looks clean on the stick, so I don't think it was a lack of draining enough fluid. The problem seems to be more pronounced when warmed up.
Also when cold, I've had an issue with it stalling while taking off from a stop. I wouldn't necessarily relate the two problems, but someone mentioned they thought they might both be a symptom of a slipping torque converter or something. But the stalling issue seems to go away when it's warmed up.
Also had an issue with the van not wanting to start when damp. But I attributed this to water getting on the coil or plugs or something. What I could try before taking it to a shop and risking getting taken?
View 6 Replies
We have a 1993 Ford Aerostar 4wd Eddie Bauer edition. This van has 150,000 miles on it. In the past 2 years we've had a number of problems related to the van idling hard and having a lack of power.
First, the van revved high and low and was unable to maintain a steady idle....I replaced the throttle positioning sensor and this fixed the problem. Next, the van was running sluggish and was very slow to respond when you pushed the accelerator....I replaced the oxygen sensor and it fixed the problem.
Currently, (a few months after changing the oxygen sensor and the problem being temporarily fixed) the van is having the same issue as before I replaced the O2 sensor (running sluggish and slow to respond to the accelerator). If you press the accelerator down (even to the floor) it barely responds, you can get it driving at highways speeds but it takes a long time to baby it up to those speeds.
When you let off the accelerator after pressing the petal down it actually sometimes gets a second of power. It also is not maintaining a stable idle (fluctuating between high and nearly dying). I bought a new 02 sensor and installed it but it didn't fix the problem this time. The exhaust smells rich in gas. What else might make the van run like this? Possible solutions for where to look next?
View 14 Replies
My '93 has the RABS lite on when I use the brakes and the brake light comes on when I use the brakes hard. While searching the topic I stumbled on a reference to bypassing theRABS with a piece of brake line, Looking for the particulars on this?
View 10 Replies
'93 2wd, standard instrument panel. Headlights and brake lights work fine. No instrument lights or taillights. The problem, at least with the dash lights, seems to be intermittent. My son has told me the dash lights are out, but they worked when I drove it later. I rarely drive the van. Is this a problem with the headlight switch? I pulled all the fuses, and checked the bulbs in the taillights, and everything looked ok.
View 9 Replies
My neighbor and son took it upon themselves to get the rear latch to catch... well they have done that..... .and then some. I have got the interior panel removed and the what i will call the latch plate assembly out of the way... I can see one Phillips head screw down in the hole ... but can get nothing to move ... this thing is rock solid on the latch bolt.... what can i do?
View 4 Replies
My Aerostar lately has been doing some weird things when going around corners. Whenever I'm going around a corner and I give the wheel a good turn the whole front end and the steering wheel start to shudder hard, and it sounds like the engine is being slightly bogged down. As soon as I finish though and straighten out it goes away immediately. Could this be the serpentine belt or the PS?
View 1 Replies
I recently bought a 1993 Aerostar. When I go to drive it after it rains as soon as I turn the steering wheel a good deal of water comes from the bottom of steering column right into my lap! Why this happens and what I can do to fix it?
View 2 Replies
My 93 with 210K miles threw a new one at me the other day. Not 1 mile from work with AC running, it started stumbling a bit at around 40MPH. I just assumed it was the AC cycling and the Van was in OD. Dropped into D and drove her on home.
Well this morning was round 2.... got about 2 miles from home and it started stumbling again (no AC this time). Just happened to look down at my digital dash and the speed was jumping all over, finally settling on 0 MPH. I got about a mile down the interstate and it suddenly reactivated and displayed 70mph.... smooth as silk.
OK, so I know that the rear diff. has a sensor for ABS, and obviously a pulse wheel on the diff. Is this sensor the input for speed? From other makes, I understand the pulse train input is "conditioned" in another device ( hardware) which then outputs to the dash display.
Based on these assumptions, I'm going to assume the crazy speed variation was playing hell with the ECU. When it settled on 0 mph it was happy again. Can't just be a display issue as there would have been no stumble. Getting ready to drive her about 3.5 hours this weekend to go trout fishing.... obviously the cruise won't work but otherwise it appears to function WITHOUT the speed input.
View 6 Replies
Have a '93 Aerostar that had something roll up against inside sliding side door and must have nudged it out of alignment. Broke off outside door handle, took off inside panel and tried prying, pushing, kicking and pulling rods, handle, linkage and anything I could get at. Any way to get it open, so I can re-align the catch mechanism??? I have tried everything I could to "muscle it" open....
View 14 Replies
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
View 3 Replies
