Ford Aerostar :: 1992 - Serpentine Belt Shredded
Dec 21, 2008
I was driving the other day (cold weather- approx 15 F), and my serpentine belt shredded. Managed to drive a mile or so to my driveway. The belt was shredded on the fan side (and had come completely off), but it wasn't torn in two. Got a new belt and installed it, but upon test-cranking, found that it was riding up one ridge on the crank. All the other ribbed pulleys were fine (PS, AC). The smooth pulleys had the belt move a little, however.
Thinking I didn't set it right, I reinstalled the belt on the crank and tried again. Same result (belt rides up one groove, towards the fan). I perused the archives, and one comment was that someone simply trimmed one groove off the belt and everything was happy. The belt found it's "groove", and didn't act up anymore. Doesn't fix the underlying problem, but
1) is this a good fix
2) any clue what is going on?
3) Do I need to get the crank fixed?
BTW, I am sure that I threaded the belt on correctly!
1992 Aerostar, 4.0L, AWD. AC+P/S....
View 9 Replies
Advertisement
So, I somehow ended up with a hole in my oil pan. Long story short: water pump seized which shredded the serpentine belt. Had the car towed to the dealer. They found the hole in the oil pan. Pretty sure it wasn't there prior to the tow, and unfortunately I didn't watch the driver unload the car when we got there. Both tow company and dealer have just shrugged their shoulders on it.
I let the dealer replace the water pump because it's not something I was interested in tackling with everything that needs to be moved out of the way to get to it. However, I towed the car home myself (flatbed carrier from U-haul) to do the oil pan. I just got
View 4 Replies
I have a concern with my serpentine belt chirping when it's wet or cold. I have tried soap, and other attempts to quiet it down. Belt tension is good, new water pump and fan. Otherwise no other issues so far.
View 9 Replies
I have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 Replies
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
View 4 Replies
So I was getting my car flashed to stage 1 at a dealership here in the Chicago suburbs and there was CSG R in there with the timing belt shredded. Turns out water pump came apart, shreded the timing belt, and apparently the pistons smashed the valves. I got a call from my friend whos a mechanic and said another one is getting towed there today with the same issue. Both have between 2k and 3k miles on them.
View 24 Replies
Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 Replies
I was driving my 2005 RX 330 (138k miles) North on I-75 through Atlanta in rush hour traffic when the car completely died in the left hand lane w/ no shoulder. GDOT stopped six lanes of traffic to push us up and over a couple of hundred yards to a right shoulder. It was determined that due to a coolant leak from the water pump the timing belt malfunctioned and shredded.
I had heard that the water pump should be replaced during the 90k maintenance when the timing belt is changed, but my water pump was not replaced according to my maintenance records. I understand from reading a couple of posts that this isn't always required but that they do check the water pump. Is this correct? And if so should they have noticed that there was a potential problem?
View 9 Replies
I have a 2003 f150 4.2 v8. and i have a squeaky belt I am almost positive its the belt i went to change it today but being sick,cold (NY), getting dark having just worked 10 hrs and changing oil it was not going well.
The reason I think its the belt it does not squeak when its really cold out but once it warms up a little its back so I am thinking when it gets warm it stretches out a little and when its cold it shrinks up or am I just crazy..
View 2 Replies
So i have a 1998 4.0 ohv ranger and have been fighting belt squeak shortly after i got it. I've replaced the belt twice and the tensioner twice when i put a GATES belt on it stopped for like month. But its still squeaking. If i put a wrench on the tensioner and turn it the squeak stops. So i need to find a way to tighten the tensioner could i somehow jam it, our hook up a turn buckle bolt to manually tighten it, or use a different ford tensioner. I really need to do something cause this squeak is just down right annoying.
View 2 Replies
My 2007 Ford Focus broke down today. From what I can see and find online with my limited knowledge, it looks like the serpentine belt broke. Would this cause loss of power steering, rise in oil temperature and my check battery light to come on?
View 11 Replies
2003 3.0 ranger... This will be my 3rd time replacing serpentine belt and if needed 2nd. time for idler, tension pulleys...NOT SURE WHAT TO DO, should i replace parts again?
View 5 Replies
I've been having trouble with my 2000 EX recently, I've had to replace the serpentine belt 3 times in the last year and a half. Nothing looks out of place but I really don't know enough about this engine yet to say that conclusively. I've been using the regular belts from napa, so this time I ordered the HD belt. Is there something that I need to look at that maybe misaligned that could be shredding these belts
View 13 Replies
Leaving on a 200 mile trip in the morning and when checking the fluids, I found the serpentine belt trying to get off the AC pulley. I've put in on twice and it immediately jumps half way off when starting the engine. How long it's been doing this. Nothing is obviously loose or moved. What is likely causing this?
View 8 Replies
I have a 2006 Escape with a 4cyl. 2.3L automatic gas engine. Recently when going down the road my serpentine belt broke. I purchased a new one and attempted to install it. However, after routing it over all the pulleys there is still a significant amount of slack. Keep in mind when putting the new one on I didn't even have to move the tension pulley. Upon starting the vehicle I was able to see that all of the pulleys were moving and doing what was expected.
However, there is a great deal of squealing and risk that the belt with be thrown off or broken. I researched and am fairly certain that it is in fact the correct size belt as all the sites indicate the same part number and size. Could this be the result of a bad tension pulley that needs to be replaced? Need access to the routing diagram in case I may have put it on incorrectly? Am I missing some other form of adjusting the tension in the belt?
View 5 Replies
I noticed my serpentine belt started squeaking about 3 days ago. And yesterday as I was driving to work I heard a clicking sound coming from the left side of the hood, then my car started to gradually shut down and white smoke was coming from the engine. When I got to the stoplight it completely turned off, but I was able to turn it back on again to turn into the parking lot before it shut off again. When I checked it there were no visible leaks, my reservoir for my coolant was still full, and my meter never went up indicating that my car was over heating. I'm not sure what's wrong with it, but after it sits for awhile it is able to turn back on again for a while.
View 3 Replies
My serp belt squeaks due to contamination due to timing cover leak. I removed belt and cleaned it with mild degreaser solution and it was quiet for 1 day. If I had 100% water in cooling system, would any more leakage cause a belt squeak? I am putting off fixing timing cover gasket since it is a 5hr job. Coolant is @ 90% water concentration now.
Taurus 3.0 Vulcan motor.
View 9 Replies
About 2 weeks ago i noticed that the serpentine belt started shredding. I noticed it before it was all gone, so i parked it and started ordering parts before i did anything. Since i had to get the radiator hose off, i decided to flush the coolant, change the thermostat and the upper radiator hose to go around the belt. Once the parts arrived, I drained the coolant and did two flushes and tried to change the hoses and thermostat. the Gates hose ended up not being the right hose, in hindsight I should have used the old hose and put it back together.
But I returned the Gates hose and ordered a Motorcraft hose. not thinking, i left the system dry and possibly sitting with water from the previous flush. Three days ago, I got the correct Motorcraft part and did the work on Sunday. since it had been sitting, i decided to run another flush, i noticed a squeaking sound and that the water was coming out a little browner than when i left it. So I ran another two flushes and said to hell with it and put the whole thing back together and filled it with coolant and distilled water.
This morning, the squeaking sound was louder, but temps where fine and coolant level was fine. I drove to work ( about a 10 mile drive) and when i finally stopped, i got a whiff of coolant smell. I noticed coolant behind me and when i lifted the hood, i noticed the reservoir was half empty and coolant dripping down from the center of the block. I can still hear the squeaking, I figure the water pump is on its last leg and decide i need to go home. I walk in to work and let them know I'm gonna take the day off to situate this. Before i leave, i top off the reservoir with a gallon of distilled water and head out.
After a short distance I notice that the squeaking stops, now I'm terrified that the water pump just completely failed. (I've never had one fail on me so I'm not sure what happens when it does) As i drive home, I'm watching all my gauges. none of the temperature gauges spike, everything was normal for the drive home (another 10 miles) I park it and lift the hood and the reservoir is completely full. why is reservoir completely full? why would a leak like that stop? Should i just change the water pump? I don't want to just hope for the best, i do use my excursion to haul the kids from time to time.
View 10 Replies
Been trying to isolate my noisy serpentine belt. Had the belt off and spun everything, only thing I found that made any noise was the alternator. It had a nice churp like a bearing was on its way out in it. So I replaced that figuring my squeak was going to go away. No such luck. Listening to it again while it was idling, I crawled underneath. Almost seems like the churping noise is coming from the Crank Pulley. Is there a bearing on this pulley that goes bad?
View 13 Replies
Just a quick question, my serpentine belt fell off while driving on the freeway today and wondering what are the possible causes for this too happen? First things that came too mind were tensioner or worn out belt. Hard to believe the belt would be worn out though as it only has 65k miles.
View 7 Replies
I was cruising along yesterday and felt the steering pump go out on the highway. Nowhere to pull over and pulling a big horse trailer. Three miles later I finally get to a wide spot to dive into. I look down and the temp gauge is maxed and the oil light is on. Most of the antifreeze boils out when I got the engine shut down. I had no choice but to have a friend bring a new belt and some antifreeze to the rescue. Got it changed and filled back up. Started and drove home fine.
I've got this twisted gut feeling about the whole deal. What kind of damage did I likely do? Things to look for? Did I just kill the longevity of the motor? I've been trying to do things right and treat it well to ensure a reliable truck.
On a side note the belt came apart in ribbons and it was absolutely shredded. The belt appeared to be less than 3 months old. No cracks or tears and a bright white numbers sticker on the back
View 14 Replies
