My `88 Aerostar needs a replacement steering column. I believe everything can be swapped over therefore color of steering wheel does not matter. Cruise control buttons and tilt are a must. I would like to find one that is tight(er) and not sloppy floppy like mine is slowly becoming (143k miles).
View 1 RepliesI recently bought a 1993 Aerostar. When I go to drive it after it rains as soon as I turn the steering wheel a good deal of water comes from the bottom of steering column right into my lap! Why this happens and what I can do to fix it?
View 2 RepliesSteering column recall ? The ford sites don't have much info yet. What is involved steering column replacement ? Computer reprogramming to sove the issue of the steering ?
View 1 RepliesI have a 1997 F150 that I have taken to a mechanic twice and it is still not right. I had a igination switch replaced and now when the humidity is really high
(I am Guessing), I can have the key in the house and my truck lights flash the radio is on and it sounds like it is trying to start. How hard is it to replace the igination switch myself. I believe it has a short someone in the steering column.
Proud owner here of a '96 3.0L RWD Aerostar Utility Van with about 138k miles, and leaking power steering fluid. At this point I'm replacing fluid from zero every time I have to drive it which is about once a week. I've located the leak and it seems to be coming from the pump/reservoir around the pressure hose. The hose is loose as in i can move it around a bit, but from what I've read, this is normal and the hose is supposed to be like that. I figure that at this mileage, with so much air going through the pump, all the crazy squealing and whining it does even when full, at this point it probably makes sense to replace the whole pump while I'm in there, as opposed to just doing the reservoir. Anyway, I'm planning to do this in a couple of weeks, and have some questions...
1) The pump - I've read on this forum that the best way to go on brand of the pump is Motorcraft.
2) Hoses - I'd like to replace the hoses coming out of the pump while I have this thing all taken apart, but I'm not exactly sure what parts to get. I know one is the pressure and one is the return, but there are variations of each based on the research I've done. The parts on the Napa site have different descriptions like "with switch port", "without switch port" "56in hose" "26in hose", and so on. Which ones I need, specifically the ones connecting directly to the pump? I havent been able to find anything in my research online, in Haynes, or Chiltons manuals.
3) Washers - Whether or not I replace the hoses, should I replace the washers at the connection point? Chilton's seems to recommend replacing them. Will they come with the new pump?
My local auto parts shop has the pulley remover/installer for me to rent so I've already got that squared away. I'm pretty sure I've covered all of my bases otherwise.
I have a 94 EB AWD I am restoring and have recently picked up an 88 EB to restore as well. The 88 did not run. Here's a list of things done.. New head gaskets, new fuel pump, full tune up, radiator flush n fill, oil change, new transmission and rear seal, new battery, new iac valve, many new lights etc. Well here's where your expertise may come in.. the van starts and runs fine for the first minute or two, but when stopped at red lights the van wants to stall.. and while idling actually has stalled. I was going to replace the MAP sensor as I have found that sometimes causes idling issues. I assume the 88 does not have the MAF sensor to clean/replace? Any other things I could check before heading to the vaccuum lines? Also, both power mirrors are inop, the horn is inop and the gas gauge reads CO. I will check the fuses for those problems..
View 4 RepliesOk all.. been working on the 88 getting it running (3.0L EB 2wd). It does run now pretty well.. definitely need some suspension work.. but that's a different post. I have had the rear main seal replaced and the oil pan gasket replaced to stop the oil leak. There is a lot less oil on the ground now.. but still leaves spots on the street. It appears oil is leaking down the oil pan from above and dripping off of it to the street. I also had the main cap bolts replaced (one was broken and the end was in the oil pan).
View 14 RepliesI took the 88 out yesterday (3.0 with rebuilt transmission).. it looks like there is transmission fluid on the back (spots all over it).. I can only assume it's transmission fluid... I tried to wipe it off... but it was kind of a mist.. I assume the modulator should be checked? I'm not sure where it is or what it looks like though...
View 14 RepliesYes, I have photos of this, its possible, I did this twice!
View 14 RepliesI have an 88 EB, and every time I fill up the gas tank and park on my driveway (slight incline) gas leaks from the top of the tank. 3 different mechanics have checked it out completely and say there it nothing wrong - including the dealer that totally topped off the tank. Does this sound like a fill line to the tank? It only leaks until the gas gauge goes down a notch....
View 14 RepliesI jump started my wife's mini Cooper using my aerostar van 3.0l cargo. Her battery was so dead we had no luck after running my van for 8-10 min. There were a couple of attempts. My van suddenly died when she wasn't cranking the mini. It won't restart.
About one week prior I had a no start situation. I thought I had solved the problem. The first thing I did was listen for fuel pump engagement. I didn't hear it. I pulled the fuel pump relay and cleaned the connections. I put it back and the van started. I drove all week and then I get the call to jump start the mini.
So back to today. Fuel pump is engaging. I checked for spark at #4 cylinder with fuel relay disconnected so as not to flood the engine. I have spark. Battery is strong. I put a new fuel pump relay in place even though it appeared to be working properly. I had my wife crank the engine and the pink/blue wire at the fuel pump relay which goes to the pump lit up my voltage tester. Power appears to be present when cranking and not just initial engagement.
I'm thinking the original no start had nothing to do with the wire connections which I cleaned and it was just coincidence that it started and ran again for a week. The connections are now clean with a new relay attached and not starting. I'm thinking if I have spark and a fuel pump engaging then injectors may not be firing???
My 1988 Mustang 5.0 GT has stalled out once last year and again recently. Same situation. I drove it for 300 miles with stops about every hour and a half. Pushed to to 90 MPH at times. Ran fine other times on the road for more than two hours. But all of a sudden the engine dies. Electrical all works but won't turn over. If I sit in it for about 10 minutes, it will start and run for the next 5 to 10 minutes than a cough or two and pull over. I have had new plugs put in and also replaced the whole distributor. Ford mechanics have stared at it and scratched their heads and say it is running fine when they hand it back to me.
View 2 RepliesI've got an oddball '88 SWB with the M5OD transmission. Since I've had it (about a year now), its always required a lot of gas to get it rolling without it stalling after sitting overnight or during the day at work, especially putting it in reverse for the first time. The shifts have always been a little choppy/jerky/grabby/whatever you want to call it, too. Mostly going into first from a stop, but you can feel it other gears too, especially if you're not flooring it.
Anyway, it seems to have gotten worse and I'm getting to the point where I'm looking at a cause. One thought I had was oil contamination on the clutch discs, I know this will make a clutch feel "grabby". There is some sludge accumulation between the trans and engine, and it appears I may have a very slow leak there.
I have to change the trans fluid this weekend and am wondering if there's anything I should inspect while I'm at it -- I don't know a whole lot about the clutch system on this van and there's next to no information on it. Frankly, I don't even know if its hydraulic or cable.
I have a 1988 Ranger 2.9 V6 that sits most of the time. The fuel pump quit working so I removed the bed and replaced the pump in the tank and the inline filter near the engine. I did not replace the inline high pressure pump because it still made a humming sound so I assumed it is working. Now when I turn the switch on I hear both pumps working but the truck will not start. It seems like it wants to fire or fires for just a second but just wont completely start. Is the system supposed to be primed and if so how?. I suspect a fuel problem but I dont know how to check pressure or check to see if fuel is getting to the engine. What to do next?
View 6 RepliesI recently came home to a shattered back window on the lift gate. We were gone on vacation for a week and I didn't notice it for a couple days after we were back. The van was backed up to my second garage door. Not really sure how it happened. Nothing was taken from the van and I live in a pretty decent neighborhood, so I don't think it was vandals. Only thing I can contribute it too is the heat (it had gotten pretty hot in WI while we were gone).
So I'm in the process of replacing it. After a pretty good search I was able to obtain a used window from a junk yard. The glass is in good shape but it is missing 3 of the 'studs' that are imbedded in the rubber molding. I have the 3M Window Weld butyl 'tape' (3/8") to seal/adhere it to the fiberglass. Will the remaining studs plus the tape be enough to permanently keep the window in place?
If not, I can salvage the studs from the old molding but then I have to figure out how to glue it to the new window. I'm not sure what I can use to do this. I've considered JB Weld, Epoxy, super glue or something like rubber cement. It looks like the old studs were ripped straight out leaving kind of a void in the hard rubber molding. The bottom of the void is I believe rubber (not glass).
I was wondering how do i replace the outer tie rod on a 95 ford aerostar awd 4.0L. I have enough for the parts but not extra tools. Need a tutorial on how to do it?
View 6 RepliesI have a squeak that developed in the steering column whenever I turn the wheel. It is as if something lacks lubrication. It does it in all steering positions. I guess next step is to open it up and see if I can get closer to the source so I can hit it with WD40.
View 6 RepliesI think my steering column bearing is bad up at the top end. I got the steering wheel off and the coil spring wire thing without too much drama, but my Haynes manual stops there, it doesn't tell how to go any deeper into column. How to proceed? Almost forgot, this is a '97 F150....
View 2 RepliesStarted truck and turned the wheel far to the right and shut the truck off to get better access to the grease zerks. Now the entire column, ignition is locked up tight. I can't turn the key, remove it, anything? Thoughts? I'm stuck
View 14 RepliesLooking for a diagram of the steering column? I am looking to see what is behind the ign tumbler that sends power to the ign switch module. I believe a problem might be there . this is for a 2000 x limited 7.3.
View 1 RepliesWhat's inside that electric clutch? Mine will not lock up. I checked the sensors, the solenoid resistance - all good. Hotwired the thing to bypass the control module - no avail. It flashes a code 9 which is a mechanical problem but I was told that the clutch is so simple there is nothing that can be broken. Does it have some kinda lining that can be worn?
View 14 Replies