I have an 88 EB, and every time I fill up the gas tank and park on my driveway (slight incline) gas leaks from the top of the tank. 3 different mechanics have checked it out completely and say there it nothing wrong - including the dealer that totally topped off the tank. Does this sound like a fill line to the tank? It only leaks until the gas gauge goes down a notch....
View 14 Replies97 Aero. Just recently experienced this weird issue. Had the AC on for a warm day and heading down the freeway at 70mph. The AC is kicking out some nice cool air. Noticed that when the van was heading up a slight grade, the air speed coming out of the vent would slowly diminish until no air came through the vents at all.
As soon as the van leveled out or started heading downhill, the vent air speed would pick back up and blow normally. This happened repeatedly. Is this a blower issue? Vent door issue? Something else? Since the van was traveling at speed, I could not tell is the blower was still blowing when I was experiencing no air out of the vents.
I have a 94 EB AWD I am restoring and have recently picked up an 88 EB to restore as well. The 88 did not run. Here's a list of things done.. New head gaskets, new fuel pump, full tune up, radiator flush n fill, oil change, new transmission and rear seal, new battery, new iac valve, many new lights etc. Well here's where your expertise may come in.. the van starts and runs fine for the first minute or two, but when stopped at red lights the van wants to stall.. and while idling actually has stalled. I was going to replace the MAP sensor as I have found that sometimes causes idling issues. I assume the 88 does not have the MAF sensor to clean/replace? Any other things I could check before heading to the vaccuum lines? Also, both power mirrors are inop, the horn is inop and the gas gauge reads CO. I will check the fuses for those problems..
View 4 RepliesOk all.. been working on the 88 getting it running (3.0L EB 2wd). It does run now pretty well.. definitely need some suspension work.. but that's a different post. I have had the rear main seal replaced and the oil pan gasket replaced to stop the oil leak. There is a lot less oil on the ground now.. but still leaves spots on the street. It appears oil is leaking down the oil pan from above and dripping off of it to the street. I also had the main cap bolts replaced (one was broken and the end was in the oil pan).
View 14 RepliesI took the 88 out yesterday (3.0 with rebuilt transmission).. it looks like there is transmission fluid on the back (spots all over it).. I can only assume it's transmission fluid... I tried to wipe it off... but it was kind of a mist.. I assume the modulator should be checked? I'm not sure where it is or what it looks like though...
View 14 RepliesYes, I have photos of this, its possible, I did this twice!
View 14 RepliesMy `88 Aerostar needs a replacement steering column. I believe everything can be swapped over therefore color of steering wheel does not matter. Cruise control buttons and tilt are a must. I would like to find one that is tight(er) and not sloppy floppy like mine is slowly becoming (143k miles).
View 1 RepliesI jump started my wife's mini Cooper using my aerostar van 3.0l cargo. Her battery was so dead we had no luck after running my van for 8-10 min. There were a couple of attempts. My van suddenly died when she wasn't cranking the mini. It won't restart.
About one week prior I had a no start situation. I thought I had solved the problem. The first thing I did was listen for fuel pump engagement. I didn't hear it. I pulled the fuel pump relay and cleaned the connections. I put it back and the van started. I drove all week and then I get the call to jump start the mini.
So back to today. Fuel pump is engaging. I checked for spark at #4 cylinder with fuel relay disconnected so as not to flood the engine. I have spark. Battery is strong. I put a new fuel pump relay in place even though it appeared to be working properly. I had my wife crank the engine and the pink/blue wire at the fuel pump relay which goes to the pump lit up my voltage tester. Power appears to be present when cranking and not just initial engagement.
I'm thinking the original no start had nothing to do with the wire connections which I cleaned and it was just coincidence that it started and ran again for a week. The connections are now clean with a new relay attached and not starting. I'm thinking if I have spark and a fuel pump engaging then injectors may not be firing???
My 1988 Mustang 5.0 GT has stalled out once last year and again recently. Same situation. I drove it for 300 miles with stops about every hour and a half. Pushed to to 90 MPH at times. Ran fine other times on the road for more than two hours. But all of a sudden the engine dies. Electrical all works but won't turn over. If I sit in it for about 10 minutes, it will start and run for the next 5 to 10 minutes than a cough or two and pull over. I have had new plugs put in and also replaced the whole distributor. Ford mechanics have stared at it and scratched their heads and say it is running fine when they hand it back to me.
View 2 RepliesI've got an oddball '88 SWB with the M5OD transmission. Since I've had it (about a year now), its always required a lot of gas to get it rolling without it stalling after sitting overnight or during the day at work, especially putting it in reverse for the first time. The shifts have always been a little choppy/jerky/grabby/whatever you want to call it, too. Mostly going into first from a stop, but you can feel it other gears too, especially if you're not flooring it.
Anyway, it seems to have gotten worse and I'm getting to the point where I'm looking at a cause. One thought I had was oil contamination on the clutch discs, I know this will make a clutch feel "grabby". There is some sludge accumulation between the trans and engine, and it appears I may have a very slow leak there.
I have to change the trans fluid this weekend and am wondering if there's anything I should inspect while I'm at it -- I don't know a whole lot about the clutch system on this van and there's next to no information on it. Frankly, I don't even know if its hydraulic or cable.
cant figur this out have no signal to injectors and no power at fuel pump 88 f150 5-0
View 2 RepliesI have an 88 E350 With a 460 EFI . Problem is there fuel is coming out of the ecs canister . It has the dual canister set up fuel comes out of the rear one after the engine starts. I have never seen this before. What would cause this ?
View 2 RepliesWorking on a 88 Ranger 2.9L 5-speed ext cab. The fuel pressure drops off fairly fast when turned off and I'm pretty sure that the check valve is bad. My question is, which pump has the check valve? It is a single mid tank set-up and has a pump in the tank and on the frame.
Pressure is fine while running. about 30psi @ idle and 40psi with no vacuum on the regulator. The pressure drops off within a couple of minutes which causes it to have to crank over for a bit to rebuild pressure and start.
It looks like the frame pump is readily available while the in take pump is special order. I just need to know which one has a check valve. I'm thinking the in tank pump, but I hate to waste money for the wrong pump.
Pressure drop rate
30 psi @ shut off
25 psi @ 1:05 min
20PSI @ 2:30 min
15psi @ 4:45 min
still dropping
I have a 1988 Ford F-250 Lariat, 7.5L 460, four-wheel drive. I have two fuel tanks on it, and I've been having a really annoying, obnoxious problem with it lately. After running it for a while, I noticed that I keep losing fuel pressure, and the truck stalls. When I try to start it, it does nothing but roll over. It just won't start. I've changed the fuel filter, I know both fuel pumps are working (I turn over the key, I can hear front, back, and high pressure pump attached to the left side frame rail kick in.) It's Fuel Injected, not EFI, hence that third pump. The problem happens a lot, and it's random. I could drive for 100 miles, stop to get something to eat, come out, and it won't start.
I thought maybe it was the fuel pressure regulator, but I don't think that's the case because it still runs. I would assume that if the regulator was bad, it wouldn't run at all. I also thought that maybe it was the relay, but according to some mechanics I spoke too, if I can hear the pumps kick in when I turn the key over, then the relay is fine. The only thing I could think of is that it might be the fuel selector switch. Maybe it's going bad, shorting out or something. When I flip the switch though, it switches between fuel tanks, and the gauge reads how much fuel is in it from the sending unit.
There's a schrader-type valve up by the fuel injectors. When I push it in, it barely squirts any fuel out, if at all, so I know the pressure is low. When I push it in on a good day, it sprays out like a water fountain. Just tried starting it again - no good. Pushed on the valve, it spurted out some fuel pretty well, but still won't start. Occasionally tries to, but ultimately won't. I know the spark is good, checked the plugs/distributor cap. Can't get the sucker to start.
After filling up today at the pump, the low fuel message is still coming on. My gauge is correct though. How to clear the message. I keep on trying to reset it with the reset button but it doesn't go away.
View 8 RepliesMy 88 F150 (300 six, 5 speed, dual tanks, 176,000 miles). The truck has the low pressure fuel pumps in the tanks and the high pressure pump on the frame rail setup. Truck starts fine, but cuts out severely under acceleration for the first 30 seconds of driving. After that I only notice the problem when applying a lot of throttle (does not cut out under gradual acceleration) or climbing steeper hills. If I kill it for a few minutes and then take off again the problem is back for the first 30 seconds or so. I have replaced all the tune-up type stuff (all filters, plugs & wires, dist. cap & rotor, ignition coil, o2 sensor, cleaned throttle body, replaced IAC valve, numerous sensors). Timing is dead on at 10 deg. BTDC with SPOUT unplugged. My FPR was bad so I also replaced that. Condition exists regardless of which fuel tank I am using (no problems with tank selector).
Getting no KOEO codes, but getting KOER code 41 and plugs do seem to show a lean condition possibly. I'm still averaging around 16 MPG since this became a real problem about 3 months ago.
I removed the bowl from the reservoir between the tanks and the high pressure pump on the frame. No filter in there, but it was clean with no gunk or sediment found. I removed the line from the inlet side of the high pressure pump and found that while cranking the engine I have fuel flowing freely (same amount of flow regardless of which tank I've switched to). The flow was steady, but not extremely strong. If I understand right the in-tank pumps are not designed to provide much pressure? Below is what I found at the schrader valve:
key on, engine off - high pressure pumps runs for about 1 second, brings gauge up to 48 psi
idle, FPR connected - 40 psi
idle FPR disconnected - 52 psi
revving throttle with FPR connected - 46 psi maximum
Connector, where fuel pump relay plugs in, seems to be clean and not corroded at all.
I have a 1988 f-250 with a 460 motor. I have fuel and I have fire. And the truck starts with I prime it. I tried looking for the crank sensor but can't find it. I looked behind the balancer and I didn't feel any wires or anything. I checked on the sides of the motor nothing. It has a new coil pack and ignition mod. Fuel pump and starter. What else can it be?
View 4 RepliesWell I've got an nice steady leak coming from the front of the pan.... running aft of course (downhill, windflow). She's down right now for an AC overhaul and new PS pump/hoses, but I'm inspecting to see what is next to get this stinking oil leakage stopped.
Front HB removal and seal of course, done in situ (in position). But if it is actually the oil pan/seal, can that be done there also? Front of the pan looks tight to the crossmember, and how the internals look (tray baffles, pump pickup) I've no clue if it will come off. Once she is back up and running I'll ascertain where this leak originates.
Interweb searches show the 90-94 4.0L engine is notorious for pan gasket leaks. None of the writeups I've found thus far determine if that pan can be pulled where she sits.
I have been having to add 1-2 quarts of oil every 2-3 days. I have noticed the back of the engine wet, but have seen no visible leaks unless the engine runs then it drips. Does it sound like a valve cover gasket problem or a rear main seal?
View 5 RepliesI have a 1990 Aerostar that has leaked gas 3 or 4 times. I am not sure where it is coming from exactly but it seems to be towards the back of the engine, kind of near the torque converter. This leak happened 2 days ago when i was warming the van up and it was cool outside. The time before that, it was after driving for a while. The day before yesterday I drove it probably 50 miles with no problems and it was about 85-90 degrees outside. I drove it today and there was no leak and today is a cooler day.
View 14 RepliesIt would appear as though my steering leak on my 1991 Aerostar is coming from the seal, where the steering shaft enters the steering box. I'm trying the Lucas treatment but it doesn't appear to be working. Can this seal be replaced WITHOUT replacing the entire steering box?
View 6 Replies