My buddy has a 97 f350 with a 460. When he accelerates his HVAC changes from vent to defrost then back when the desired speed is reached. What can be causing this?
View 1 RepliesI have to once and for all try to figure out what the heck is up with the AC and the defrost/vent switching back and forth. I have searched and searched and posted a few months back as well. But now that it's summer and 100 degrees out I've had a chance to test some more.
1 - I replaced both hoses going to the hubs up front.
2 - I am not sure how to test vacuum, but I did cap the hoses that lead to the hubs and still had the fluctuating back and forth
Looking for detail how to test for vacuum leak with a gauge directions ? What number is supposed to hold on the gauge and for how long etc...?
3 - It used to be that when I got to a high speed or RPM it would shift to defrost, but now I've noticed that once on the freeway going to work for instance and doing a constant 55-65 ( sub 2k rpm ) for about 20-25 minutes the vents hold fine. When I start to stop and go with higher RPM's it starts to 'break down' again. Could it be that there is a vacuum canister or pump ? I don't know ?? The diesels have a vac pump - do the V10's ? What can I check if there is no vacuum leak - what's next ?
My switch is bad. I took it out and looked at it and cleaned it up and put it back in. The lever slides smoothly without stopping at the desired speed. Contact is made but the switch likes to pop up out of the assembly. I could use zip ties to keep it in, but like I said, it doesn't work properly anyway. I have looked everywhere in the searches and used parts links on the Geo Forum but can't find one.
Any blower switch that I can put in my Geo Metro '97, 1.0L, 3 cyl., base model with std. trans.? I need the switch/cover that is at the top of the picture, It pops in above the lever and by the 4 little clip rectangular holes coming up from the assembly.
Inside the switch there is a small spring and ball bearing about the size of a bb that causes the switch to "click". Spring and ball disappeared long ago. -- From a different thread. Does the spring and ball bearing come with the switch or is that a separate item?
I've got a 03 x with the 6.8 2wd 4r100. It was flaring pretty bad for a while going into lock up, about 2 months ago the flare went away now NO lockup. Its taking more pedal to get moving and alot more slip, once you reach cruising speed tranny goes into high pressure. Told to replace the selonoid pack, got one use from a tranny shop from a tranny that lost reverse, got it home took mine out and found out the new one is not PWM and mine is, I tested my selonoid by putting 12v to pin 1 and 4 and nothing (on the pwm pack) did it to the new pack and it works. My question is what will happen if I put the non pwm in my tranny that originally had pwm pack in it?
View 2 RepliesI have a 2005 F350 6.0 with 4 wheel drive.
Late last winter, the 4WD stopped working. I diagnosed it to be a vacuum problem. Like a moron, I purchased a vacuum pump and threw it in there, I just figured that it was bad. It turns out the new pump I bought was bad, but the old pump was fine... Go figure. At any rate, when I switch to 4WD, my HVAC goes to full defrost and the 4WD does not engage.
I think I've narrowed the problem down to the 4WD actuator, since if I hook the vacuum pump output directly to the hubs, the 4WD works fine. If I switch it into 4WD, I can hear the vacuum releasing in the actuator, but it doesn't seem like any vacuum actually gets routed to the hubs. It just opens to atmosphere.
I've noticed that after switching to 4WD, the actuator only "Releases" the vacuum for a few seconds, and then seems to close itself. Is this normal? If I cycle the 4WD selector from 2WD to 4WD repeatedly, it will continue to cycle.
1. Is there any way to service this valve, or should I replace it?
2. Is the valve acting normally?
3. Am I on track with this repair?
My 06 F250 crew with the 6.0 starting blowing the cold AC out the defrost vent and will not switch to the dash vents. It's goning to hit 108 today and stay around 105 for the rest of the week.
View 14 RepliesI've got a couple different problems. The first one is that no matter what setting I have it on, air only blows out of the defrost vent.. Why this is happening? or is there already a thread about this? i saw a thread for this same problem, but it was for 2nd gen explorers.
The second problem I have is that there always seems to be air blowing from some where on the passenger side, unless i am accelerating. I can't seem to find where it is coming from but it makes a really annoying noise.
It is the 4.6L, AWD. not sure if that matters or not though.
Title pretty much states it. A while back both my ABS and my ESP light would come on after I reached a speed of 18mph. After some research here I figured it was just a dirty sensor. So I cleaned the front ones and still haven't got around to the rear, but I told my mechanic to scan it. He says I need a new ABS pump which I am hoping, he is wrong. Printout says...
01276-ABS Hydraulic Pump(V64)
008-Implausible Signal - Intermittent
008-Implausible Signal - Intermittent
So I am hoping it is just dirty or unplugged and not the ABS pump.
is there an way to remove the defrost vent covers? i think my license slid down the front of the defrost covers. its probably somewhere down under the dash. I would like to start removing the covers up top before I yank the dash. I am 1400 miles from home so I cant run and get a replacement.
View 6 RepliesHow "ECO" mode actually works?
When I first got my new 2012 Camry, I noticed ECO light would come on mostly on the highway when I reached certain speeds, and seemed to come on more when I had air conditioning on.
However, now it seems more often the ECO light is on all the time, even when I come to a complete stops. Just wondering if this is normal or do I need to take it in to be checked out or what?
I know ECO mode works with speeds and air conditioning. I do notice when ECO light comes on, the AC doesn't seem to be as cold.... I want my AC working as cool as possible!!! It's constantly over 100 degrees here in San Antonio in the summer.
My 2006, King Ranch, 4x4, 6.0's air conditioner only blows from the defrost vent. I have done some research on here, but haven't seen anything that identifies as a common problem. I did however, notice that this problem is stemming from a vacuum issue.
View 10 RepliesMy husband and I have 3 Excursions, V10, 6.0, 7.3 and I have a 6.0 250 crewcab. 3 of the 4 now blow air or heat from just the defroster unless your going at a slow speed.
View 2 RepliesMy 99' started o blow air only through the defrost vent today, and won't go through any of the other vents. I think this happens when your vacuum pump goes bad or there is a leak, correct? If so, how can I test these to figure out the problem.
View 2 Replies2006 F250 5.4 - While driving ac changes from vent to defrost on it own..let off gas and it will change back to vent. I replaced vacuum can under hood.. no luck.....
View 1 RepliesI have a 2000 f250 4x4 7.3 diesel. I had problems with my a/c and controls for sometime now. my a/c was blowing threw the defrost vent. I was told my blend door was bad. I bought a new blend door installed it,still doing the same thing. I was told to check my vacuum lines. I check them, they were bad. I replace my vacuum lines and my vac pump as well. that fixed my problem blowing threw the defrost vent. I can control my air flow from floor,dash vents and defrost vent. the problem I have, I not able to control my temperature when I turn my center from red to blue. It blows hot air and the air that is coming out of the vents isn't very strong at all.
View 1 RepliesThere is always something.... I just drove my girlfriend's new 2003 ranger edge home from the seller. Real nice truck. I noticed the heater selector doesn't change the air flow. It is on full blast for the defrosters, and is also trickling out of the floor and dash vents. No matter where you put the selector, thats the only place the air comes out.
The temp control seem to work OK, when you turn it on cold, you get cold air and visa versa. Even on AC and MAx AC... air out the defrosters. It's cold when you turn the temp control to cold.
I did some searching here and gather some info on checking the vac lines etc. Everything looks in place but one detail. The vac ball under the hood under the air box has 2 ports on the front end, and only one grey line going into it. The other port has what looks like a rubber boot and part of a very short vac line broken off it.
I looked, I cant find any loose vac lines. I'd like to know if this second port is suppose to have a second line on it, and where does it go? What color is it? Is this the reason the vent selector isnt working?
I have a 2012 F-350 SRW with a 6.7 diesel. The other day I went to push the defrost switch and noticed it does not work. All the lights work in the switches, and the temp control works, but no matter what I push, defrost or floor, it stay in the vent only. Anything I can check??
View 1 RepliesI have a problem with my vent selector on my truck. It's a 2005 f350 lariat. The vent is stuck on defrost, some times after a few mins I can get it to switch to floor but not always. I have replaced the pump, checked tank for cracks, disabled and plugged the auto hubs. The pump will shut off so I assume it's not a leak. I believe it's in the switching unit, can these be repaired? I found a lot of dust and dirt in the vac tank that had been sucked through a bad hub. I think it may need to be disassembled and cleaned. I have seen videos showing how to replace the orings in the older units. Are the newer style remote ones the same?
View 5 RepliesWent to use my windshield defrost this morning on my way to work. everything went fine. Leaving work I selected the face vents with my AC on and it only blows hard from the windshield vent even though its already been depressed.
View 4 RepliesExperienced the problem of a flashing defrost button and the entire HVAC system "frozen"? All the other buttons become useless while the defrost button is flashing on and off. If I then hold either the a/c button or the auto button, the system starts up at 75 degrees with the air running. I can then adjust to where I want it to be.
View 13 RepliesI have a 2001 Montana. Recently I have no heat/air movement via the defrost vent. All other setting work along with fan. Plenty of heat when set on floor or dash vent. Just doesn't work with the defrost setting in either alone or with the floor.
View 2 Replies