Ford A/C :: Clutch Started To Smoke - Compressor Seized?
Aug 20, 2016
I just bought a 96 f250 5.8
Upon driving home, i tried the ac again and the ac clutch started to smoke. I replaced the clutch with one from autozone, but when I tried it again, it made a screaming death noise upon clutch engagement. Is my compressor seized?
I tried to turn the clutch (not the pulley, that spins fine) by tapping one of the slots and bolts with a screwdriver/hammer. It was firmly locked in place. If the compressor was OK, would it have turned easily? If I need to replace the ac pump, who sells a good/cheap/reliable one?
View 6 Replies
Advertisement
I haven't been on for a while but new issue my AC won't work the compressor is not seized it just wont come on checked all the fuses and tried to check the wiring but it is so short then it go's into the main wiring harness is there a way to see if it is the compressor or not some way to test it? It is on my 2002 explorer 4.0l vin "E" eddie bower.....
View 13 Replies
I have a 2001 ford f150 with a 4.6 liter v8, my ac compressor is completely seized up, I can't afford to replace the ac right now. So I would like to just get a shorter serpentine belt to bypass the ac for now, need to get a measurement on the shorter belt for my engine? and the proper way to re route the belt without the ac?
View 7 Replies
I recently had a full tune up at 87,000 miles. My receipt does not mention any inspection of the A/C system. 50 miles after the tune-up, my A/C compressor seized. Dealer claimed this was simply coincidence. I think there is a chance that they checked the A/C Coolant level and may have not secured the valve. I cannot find on the internet evidence that this compressor is prone to failure at just 3 years (87,000 miles).
View 1 Replies
Two weeks ago, I had a/c repairs done which involved the replacement of the a/c field coil unit and a condenser fan motor. Yesterday, the compressor seized up. Could the repair, if done incorrectly, have caused the part failure?
View 7 Replies
My ac compressor has seized up and now needs to be replace at a cost of nearly 2,000. Maybe I can go a few weeks with out it, but I will not be able to have heat or defrost as the colder temps come in for the fall. Why this would happen? 109K on the odometer. The mechanic also suggested that I change the timing belt and the water pump (neither are broken) replacing these is also expensive. am I crazy for not changing the timing belt and water pump?
View 10 Replies
The car is an '06 Passat 2.0T 83k. A few weeks ago my wife came home complaining that the battery light was on, when I lifted the hood I saw that the belt was shredded and later realized the compressor seized. I replaced the parts recommended; Compressor, condenser,etc., brought it to service station that does our fleet cars and had the system vacuumed and recharged. Now the compressor will not turn on, when I push the button on the dash it lights up but no a/c, the fans dont even come on comes on. The blower and all the related switches works but no power to the compressor. All the fuses are fine, and when the guy at the service station put power directly to compressor it comes on and works fine, he also said the pressure sensor/switch checks out fine. I even changed the controller on the dash, but nothing.
View 11 Replies
My wife has a 02 Ford Escape XLS with a I4/manual trans, she has been saying it has been making weird grinding noises for a while but has not been able to replicate it for me to hear. Today it locked in gear and stalled, she can depress the clutch and start it, but can't take off in whatever "gear it thinks it's in" and it'll stall. To quote her.
So odds are the clutch or trans is toast, I'm more of a full size truck guy when it comes to doing work, what to look at? She's getting it towed and I have enough tools to do the job just not a ton of time this second to do the research, When I know more I'll add it.
View 4 Replies
I have a 2001 Subaru Forester which has 165K miles. I had the timing belt changed at 105K per maintenance recommendations. I had the car in for service recently for brake pads, etc., and the dealer recommended replacing the drive belt for the AC.. which I did. 100 miles after this service, the car broke down unexpectedly. The dealer told us the AC compressor seized up... and this caused the drive belt to get caught on it and be shredded ... and with that, the sudden resistance from the drive belt on the crankshaft pulley caused the timing belt to slip out of sync and damage the interference design engine. Can that really happen? I surprised that this happened a few days after replacing a drive belt and wondered if somehow the service work done with the drive belt could have caused the problem. The dealer states the service work did not cause the problem. Is my recent service and damaged engine a coincidence as the dealer said or are they related?
View 3 Replies
i replaced my a/c compressor on my 2006 f-250 2 yrs ago but had not refilled with r134..only the pag oil. Now i decide to refill seeing my wife uses the truck and compressor would not engage, i was able to bypass it by removing relay and jumping it with a paperclip. Compressor started up but seems to have seized on pully. the pulley seems fine and still turning freely. I can no longer turn it manually when truck is stopped and i could before i jumped it. could the clutch only be replaced or does the bearing and pulley have to be replaced
View 10 Replies
I just replaced the clutch plate and throw out bearing since the clutch was bad but now its like the clutch has seized up or maybe the transmission is bad. I did start it up and a friend of mine Idk stepped on the gas or something and blew the clutch master cylinder.
2001 Hyundai Elantra ... I dont know anything about this car ....
View 2 Replies
2007 Accent pedal won't depress. Bearing making noise for a few months. Is tranny snout toast or is it fixable?
View 2 Replies
So clutch doesn't engage and compressor is not running. I have 12-13v at the low pressure switch and the same at the high. When I jump the low pressure I don't get any voltage at all at the plug that controls the relay for the clutch.
Where I'm confused is:
Is this a low pressure problem - gauge is reading 60psi on the accumulator
Or
Is this electrical somewhere?
View 7 Replies
I just picked up a '94 7.3 IDI Turbo, and I can't figure out what ails the AC. It appears that there should be enough refrigerant (according to my recharge kit), but the compressor clutch will not engage. I have checked the fuses, and all are fine. All other HVAC functions are normal. Is there a way to test the compressor?
View 5 Replies
I have a 2002 F250 on which the AC compressor clutch is not cycling: I have checked and added coolant so low pressure is correct (don't have high pressure gauge). I checked the clutch air gap and it is at 0.030 " as specified in another post. I replaced the low pressure AC cycling switch (on the evaporator/dryer). With the AC on, I disconnected the AC cutoff switch and the clutch disengages. This circuit has the correct (>10V) going to it. I am thinking it could have something to do with the AC relay.
When you switch the ATC to a setting other than AC or Max AC, the clutch disengages fine. I noticed this problem because the AC shuts off when it is really hot, after I have been driving for a long while, about 1 hour or more. If you shut off AC, wait a few minutes, then turn on it works fine.
View 3 Replies
I have a 01 f150 4.2L and a while ago the ac compressor clutch broke. I didn't catch it in time and the stress it caused on the belt broke the power steering pump pulley. So I replaced the steering pump and pulley and the compressor the accumulator/dryer and the office tube put the 134a back in and everything worked fine. three months later ac stopped working. I figured the condenser was bad so i replaced it. Charged it up still no cold ac. so i thought maybe the manifold that goes on the compressor was clogged so i replaced it. While I did that i said to myself well i should tear out the dash and replace the evap as well. so just about everything has been replaced on the ac system.
Aside from the cycle switch and the high side switch witch from my test both seem to be working. now here is the thing. the tube witch holds the office gets ice cold then goes to the evap but the suction line coming from the evap doesn't get cold and the ac blows warm air. this very problem is what convinced me that the evap was clogged and needed to be changed witch is why i undertook the task of tearing the dash out. in all it took 14 hours to do the whole job. now for the pressures that i get from the ac manifold low side goes 40 down to 20 ..... this is normal. high side is a little high. I charge it to 125 still no cold air. so i dump a little more 134 in. at 90 degrees high side pressure should be around 200ish i get it there still no cold air. I have just about replaced everything i can think of.
View 7 Replies
He has a 96 explorer and his ac compressor clutch was cycling on and off. So he went and bought 2 20 ounce cans of 134a and proceeded to add it to the evaporator service port. Of course a lot of it sprayed out side of it as it did not fit well (duh). So he has no Idea how much he actually got in there out of the 30 or so ounces he dispensed. He is laughing at himself with me on this. He says hi ahead of time
I have access to good gauges and a reclaimer and vacuum as I work sometimes for a residential ac guru. So what to do? I was thinking the evaporator should be changed out but I want a second opinion. Then vacuum and add new 134.
View 9 Replies
Says A/C Compressor Clutch Circuit open. A/C blows hot air....go to VENT and the EATC controls the temp fine (ambient air only). It's on a '97 Lincoln Mark VIII if it makes any difference. Pulled code # 1530 ...
Clutch does not engage but the compressor does turn. Also the EATC will NOT go into the test mode. Push OFF and Floor at same time, then AUTO within two seconds. Nothing. Is this a clutch gap problem? New clutch was installed about a year ago.
View 10 Replies
I have a 94 Ranger with 2.3L motor. Last week my ac quit working. I push the in and the ac light goes on, but the compressor clutch won't engage. I changed the relay, but that didn't work. The fan still works, but the ac does not come on. I tried banging on the compressor pulley, but that didn't do anything. The clutch is not frozen -- it spins freely. The connector looks good and I haven't done any work in the engine compartment so I couldn't have accidentally moved any wiring. What I might try or is my compressor simply dead?
View 2 Replies
2000 Explorer Sport with 4.0L SOHC engine. When I turn on the A/C the clutch on the compressor cycles off and on every 10-15 seconds. The A/C cools and the gas charge is checked as OK. Is this normal?
View 1 Replies
The clutch in my ac compressor is not releasing causing it stay on all the time and not cycle and get hot and freeze up the system. Also pulley seems to be angled like it's not sitting straight. Can I just replace the clutch on the front? if so what's all involved. I need to do the entire compressor?
View 12 Replies
