Ford A/C :: 2009 Escape - HVAC Blower Motor Do Not Seem To Move Any Air On Speed 1 And 2
Jun 27, 2014
I bought my youngest daughter a used 2009 Ford Escape (out of warranty) a week ago. Manual HVAC controls, 3.0 V6, AWD, 73K miles. The HVAC blower motor do not seem to move any air on speed 1 and 2. However speeds 3 and 4 appear to operate normally. Speed 4 noticeably puts out more volume of air then 3. Each 3 and 4 operator what seems to be normal speeds for their setting.
I would normally suspect resistor but my experience is usually that you have all or nothing not it's partially working like this is. I don't mind throwing a new resistor in there and trying it but I rather come up with a better way of troubleshooting it then throw parts at it.
View 5 Replies
Advertisement
Blower motor only seems to be working on the 3 & 4 position? Resistor bad? What is the location?
View 1 Replies
I have a 06 Mercury Mariner and this past week fuse #26 keeps blowing turning the HVAC blower motor off. I replaced the blower motor since i had one already in the garage and same thing is happening. The AC will run for awhile and in about 10/15 mins the fuse will blow. Fuse #26 is the Climate control system mode switch, are these known to go bad? Is this the part I should replace or look for other problems IE compressor?
View 2 Replies
I replaced the blower motor resistor on a 2010 F150 with dual climate control where the blower was stuck on high.
After replacing the resistor, now the lower speeds work fine, but when placed on high speed, the fan completely shuts down. Replace with the old resistor, and it only runs on high.
How to proceed, or what else might be the problem?
View 7 Replies
My HVAC blower motor stopped today while the wife was driving the F250. I thought I should swap relays (with the heated mirror relay - same Ford Part Number) to rule it out or identify it as the culprit. However, since these are close to the firewall, I have a hard time getting the grip and leverage to pull the relay out of the Battery Junction Box (BJB). How to make this a bit easier?
View 5 Replies
My blower motor does not blow hard on high. 2009 AVALON.
View 3 Replies
I am struggling with it, and need to get it done - by myself, as I can't afford a service job. I am handy, and comfortable doing it, But I am confused about how to get into the blower housing.
View 4 Replies
Was 7 degrees F out this morning. Went to turn on the defrost and heard this: (may need to turn up audio a bit)
2013 F150 HVAC blower noise in cold temps - YouTube
There was some snow/ice buildup under the "grate" that sits above that I imagine is the air intake for the blower. Hoping that it was just Ice buildup that will thaw out.
I ended up having to turn it on because the condensation on the windshield was becoming a safety issue when I drove into work. Motor made quite a high pitched wine. Better that than slid into a car.
View 1 Replies
Where the blower motor resistor is located on the '05 model.
View 11 Replies
I have an '02 F150 XL. 200k miles. My a/c blows cold, and I have every fan speed, but it just doesn't blow very hard. I replaced the blower motor thinking that would work, but that did nothing. I've been told to clean the evaporator core, but I don't know where that is. How to do that, as well as any other part causing the problem.
View 14 Replies
I have google it looked all over was told it was under the hood next to the fan even shown a photo when I went under the hood right were the resistor was in the photo there was a long black box about 4 inches long and 2 inches wide. looked nothing like the photo.
So I went back on line and read that its above the passengers feet you take a few screws off after you take the glove box off and it should be there. Well after taking 8 screws off I find nothing but a coil behind there. Nothing that looked like a resistor.
2006 f350 diesel?
View 11 Replies
I recently bought a 96 ranger.I noticed the fan did not work but for high. I search the internet and found how to remove it and discovered a mouse nest(village) which basically took over the housing where the evaportor core,blower motor resides. I bought a chilton but cannot remove the housing around the core so I cleaned it the best I could(air compressor and vacuum and disinfectant)...
I had to buy a new blower motor and resistor. However, I cannot find the hose that attached to the blower motor?-mouse had chewed a hole in the one- I've looked and found serveral differents names for it but seems I cannot find it at my local parts store.
My question is- is this intake hose? vent hose? I'm guessing I will have to go to dealer or, if I know the name I can look it up in a salvage yard?
View 14 Replies
My 2010 Expedition Limited AC seems to be stuck in the highest fan speed setting. Changing the setting on the panel control do nothing to change the speed. But you can adjust the temp and it will respond. It is a dual control unit. When I try to turn the system to off completely it will go to what I believe is the vents and stay on full blast. If I turn the truck off and on again the whole system remains off until I turn it on again. The only way to turn it completely off is to turn it to off mode and turn the truck off.
View 1 Replies
Have a 2004 F-250 and blower motor speed 3 is not working..replaced resistor pack with Motorcraft part and everything works except position 3 ....
View 6 Replies
Currently My AC / Heat blower motor operates but, speed 1 and 2 are the same, 3 and 4 are fine. I replaced the blower rheostat that is located on the firewall, but still no difference in fan speed.. A few years ago the blower only operated on Hi and the rheostat was the problem then.
View 3 Replies
I have and 07 F250 and the #2 speed for the blower motor don't work (hasn't since I bought it) I read that the most common cause of this is the resistor under the hood on the firewall so I replaced that and still no 2nd speed??? Where I look next? Motor itself maybe?
View 11 Replies
Have a 2009 platinum, 5.4, supercrew with dualzone heating and air. The blower motor resistor block is overheating and melting the connector block. fooled with it way too much, and then put a new resistor and pigtail in it. The new resistor would kick out in about 30 seconds, so used the old resistor on the new pigtail, got hot, melted the new pigtail. What is causing the resistor block to get so hot, and what do I do about it?
View 7 Replies
What is the testing procedures for the blower motor controller on my 2009 150 Lariat. In the old days it was called the resistor but now it is computer controlled for the dual climate control. My fan is stuck on high, the fan switch does work(the bars on the display change when I push the fan speed button). The climate control works also, just blasts you with air and the temp is changing a lot due to the fact of the fan on High. I am 99% sure it is the blower motor controller, but I would like to test the controller.
View 14 Replies
Air Conditioner Blower Motor on any speed, lets say high. Running fine while driving. Come to a stop at idle or shift to N or P. A few seconds later the blower begins to vary its speed in pulsating rhythm in what would seem to be in cadence with what would be a rough or varying idle. Where to start? Is it the relay?
2002 BMW 330ci Convertible
View 2 Replies
I have a 99 Olds Intrigue GLS. Going on 163k miles. She has been pretty good with the common fixes for this model. I decided to replace my upper and lower Coolant Hoses before I took a long trip. Everything went OK until I tried to use my AC later that day.
During my Coolant change out I did indeed start the car multiple times and eventually I disconnected the battery to reach a hose.
Now, when I turn on the AC, the Blower motor does not directly respond to my dash board speed control. The little bars indicating higher speed changes up and down as normal, but the blower doesn't change with it. Also, I can SOMETIMES get it to change speeds by turning the speed all the way up then back down a few clicks etc...Currently, when I turn on the car the AC does kick in under the hood, but the blower stays off.
Something fishy going on. I decided to disconnect the battery again and see if anything "reset". No Luck. I think it coincidental that it happened during my Coolant change out...
View 1 Replies
I am pretty satisfied with the performance of my 2009 Ford Escape. Two years 51,000 miles after I find that the rear door does not open. Following threads of earlier Escape models I find how to remove the inside panel and open it manually. After a thorough study all I need is a replacement latch motor. The plastic latch cover has the following number GA6 GF30.
View 14 Replies
