I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.
Mounting the shock with the boot up or down? I know it doesn't matter according to Bilstein but one way has to be better than the other.
Second. What are the torque specs for the upper and lower bolts? I know the lower front is around 350lbs but haven't found anything for the rest. found out the rear bolts are torqued to 66lb.
Third. The front shocks didn't come with a boot to protect the shaft. Is one needed when the shock is installed?
Truck is a 2012 F150 FX4.
What are the torque specs for tie rods for a 4x4.
View 4 RepliesI have been reading here about alternate methods to torquing the hold down bolts for the injectors. This winter I replaced my old stock split shots with new alliant single shots. I installed the injectors into a cold engine and torqued the hold down bolts to 10 ft lbs. I did not ever go back and re-tighten.
Is it suggested to go in and re-tighten the injector hold down bolts to 10 ft-lbs after the engine has been heated up and cooled down? What are some symptoms of a loose injector? I am imagining premature wear on the injector cups, low compression and maybe some mixing of oil into the combustion chamber.
Did just throw the injectors in and go back later to retorque only to find they were all fine or were some loose?
I wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?
View 1 RepliesWhat the torque spec is for the driveshaft to rear differential flange mounting bolts on the 99 F150 4x4 supercab?
View 1 RepliesTell me the torque specs for the various attaching nuts of the front hub assembly for the 99 F150 4x4 5.4L (large nut on the spindle, mounting bolts to back of spindle, etc if any) ? I will need them to put everything back together after checking the tone ring for my ABS problem.
View 1 RepliesWhat are the torque specs for front and back rancho 9000xl? Really want to know the front top spec with the rubber bushings that squish flat the most.The rest ill make tight.
View 14 RepliesMy water pump went out. Besides the obvious replacing the pump is there anything else I should do while making the repair?
View 14 RepliesI have a 99 SD 7.3 with 210K miles. It has the OE water pump, clutch and fan. I am replacing every thing from pump to fan including pulley, thermostat and sensor. The question is can every thing be removed as a unit? I don't see why not but never did one that way.
View 14 RepliesHow hard is the water pump to replace on 1999 f250 7.3 ...
Any thing special i need to know before tackling this job ...
Also is there any step by step instructions ???
I have a 2001 F250 Super Duty V8 7.3 L. I removed the water-pump then waited five days for the oring for the new pump. I installed it and now the truck will not start. I have drained the fuel water separator and replaced the filter. On the passengers side through the kick panel I found that button popped out so I pushed it back in and still it will not run. It acts like its not getting fuel but if my fuel water separator is filing up I'm assuming mu fuel pump is working??
View 7 RepliesTrying to fit my edge fuel pressure sensor. I have a 90* fitting from Diesel O-rings and I can't seem to get the 90 elbow to turn all the way down before it makes contact with the fuel bowl housing. I'm using the drivers side port, should I use the passenger side port? would it have more clearance than the driver side port?
My instinct is to crank it all the way down then tighten the nut, should I just screw it in until it makes contact then tighten the nut? I was worried it wouldn't have enough threads in contact to seal as well as it should and leak.
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 RepliesSo the water pump on my early 99 (158k miles) is starting to leak just sitting in the driveway, did a little research last night and read a few write ups. Just wondering if any tips or tricks I could use to make this go easier. Also any list of parts I should replace and/or might need. I read on one write up about replacing it with an Airtex water pump and was wondering about what people thought of those, I would rather fix it right then just go with the cheapest parts. Possibly there are better brand water pumps out there?
View 5 RepliesWhat is the torque value for the 2 bolts on the upper radiator hose water outlet on an '04 4.6L?
View 1 RepliesI am in the process of replacing my water pump. After I removed the pump, I found quite a bit of metal-on-metal wear between the impeller and the water pump housing. Is this common?
I've been running a coolant filter on my system for years now, so hopefully its been effective at collecting some of the metal that has clearly been worn away. Either that, or this is a sign that the filter isn't working at all!
I'm a little worried that the new pump will scrape the scars left from the old pump.
Would it be a good idea to change the injector hold down bolts when I do the injector o-rings? They have never been out at 333,000 miles.
Plan on doing glow plugs, injector wiring, valve cover gasket's, intercooler pipes and the dreaded oil cooler.
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesSo I had recently developed a leak in the up pipes behind the collector. Big surprise, right?
Well, a 6-point socket was spinning on the collector bolts (probably from rust) so I decided to cut the manifold to up pipe bolts. Got the up pipes off/out. Well after and <acronym title="Manifold Absolute Pressure">MAP</acronym> gas torch, I can't punch ANY of the bolts out.
There is little to no room to get to the bolts. (I have the down pipe removed.) At this point I'll try a few more doses of hot wrench and PB Blaster, but if I have to do the manifolds I'll just pull the engine, since chances are there will be at least one stuck bolt there, too. I really don't want to go that, but eventually I'll need to install my new oil pan anyway.
Tried to flush it and got as far as draining everything. I can't hook up my T and begin the flushing process because I can't remove the thermostat. I have a buddy who can get the bolt out but I'd have to be able to drive the truck to him. I've tried just about everything to remove it. I did manage to find some replacements for when I do get the last one out though .Is there a way to still flush this thing like maybe just hook up the hose to the t and run the engine with the heat on to open the thermostat?
View 14 Replies