I just recently installed a CTS2 Insight and wondering what the typical boost pressures I should be seeing without a load just normal driving. Right now I am seeing mostly 0 unless under acceleration then it goes up to 10 psi if I floor it I am getting 15psi.
View 14 RepliesI have an 03 6.0 Power stroke. My problem all started the other day when I started to occasionally not get any boost on acceleration and lose of power and a lot of vibration like it's about to cut out but it got worse now today I drove it about 5 miles into town when I got to town I noticed a rough idle I got gas in a gas can not in the truck. I got back in to leave and I had absolutely no power at all the truck stalled out and it was very hard to start finally got it started and it runs really rough almost like it's going to shut off.
So when I started driving I would only make it about a mile or so with out it chocking out and having to let it site for a minute or two and start it back up and go another mile or 2 and have it do the same thing all the way home all the time I have vary little boost if any at all except for when I first pull out now oil pressure is good and engine never over heated some of the codes I have is an EGR code and a contribution balance code for several cylinders I was thinking possibly a maf sensor or a clogged egr not working right.
This was briefly discussed as part of another thread. It appears that I have a boost leak when I hit roughly 24.5 psi. The leak seems to stay for a few minutes after showing itself, but then I'm able to produce boosts up to 24.5 again. For example, on my 20-mile/30-minute drive to work, I can make this leak "appear" four or five times, maybe more if I try. Does this self-healing leak ring a bell? I haven't done a boost leak test yet, but I'm leaning towards the RTV sealant at the OEM plenums due to the self-healing attribute.
To add a little info to this thread, I recently installed an S&B intake, 4" exhaust, bellowed up-pipes, RR billet wheel, RR CAC intercooler boot kit with new clamps, RDP reinforcing plenum inserts, AIH delete plug, and I removed the wastegate solenoid along with the red and green tubes. I don't have any gauges, but I recently began monitoring the boost using FORScan. Before all of this, I don't think I was producing enough boost to cause this leak, and I had no way to monitor for this leak.
Well I am at a loss now. Rebuilt the turbo with a new wheel and kit from Riffraff. I still have no power, no boost and no codes. The new wheel whistles. I can hear it. It sounds way better than the old one. But still no power. I really don't know what to do now.
View 14 RepliesShort version is that I just did the EBPV delete with new pedestal and turbo exhaust outlet and put a new turbo middle cartridge in as mine had blown a seal and possibly broken the shaft. Once I got it all put together, I took it for a test drive and it was building 20PSI like it used to but I didn't have the accumulator and turbo mated up fully so I had a leak there.
I corrected that and now don't get any boost until I get to about 2500RPM and then it only builds to about 10PSI. I've double and triple checked all my connections, boots, etc. and everything is tight on the intake, intercooler, up-pipes and collector, exhaust and the spider, I can't see or feel any problems there. I tried disconnecting the MAP sensor and it might be a little better but not even close to normal.
Tried disconnecting the red line from the wastegate and plugging it with no difference. I'm stuck, and frustrated. I do have AE, watching the MGP looks like the MAP sensor is working. I feel like I'm overlooking something simple but I just can't figure out what it is...
I disconnected the red wastegate hose in order to address a low boost high EGT issue. This seemed to fix the boost / EGT issue for the most part, but now I get this P1249 code. The first time I got it I saw boost at about 20 PSI. I figured I would try to keep the boost below 20 in an attempt to prevent the code.
I managed to capture some log info when throwing the code. The highest boost reading I saw was 19.58. Pretty close to twenty but I question if I even should be getting this code at this level of boost?
Here's a chart with the boost info. Yes I still have a very bouncy EBP and hope to track that down at some point as well....
Bought the x in feb, put in the billeted wheel, modified the turbo pedestal, put in dorman uppies, put my boost leak detector on it and had no leaks then. Also put on the walker btm and gauges at that point. Took my chip to a local to get tunes. I was pleased enough with the power, and can hit 24 psi. However, it smokes like a freight train if I give it much pedal. I don't drive it a ton, but in the last week I did a 400 mile trip to pick up a trailer, then 800 miles on vacation in Colorado. The fender flare by the exhaust is now black.
It has to be pulling a trailer or going up a decent hill while cruising at 70 to show any boost at all on the gauge. If I give it gas, it belches out the smoke, unless I get on it and get the boost to 10 or more. Most of the time while cruising along I don't need to speed up that much so it just smokes and doesn't build more than 2 psi boost.
My f350 by comparison usually runs 4-6 psi boost running down the road at 65, and slight movements of the accelerator can affect that number immediately.
I don't have my leak detector with me so I can't verify that I have no leaks right now, but I can still hit 24 psi... Last night I used oven cleaner and got the whole area around the turbo pretty clean. Drove it 60 miles today, and don't see any soot around anything, maybe it's to soon to tell? Is there anything else I should check, or is it as simple as getting new tunes?
I bought a ts 6 position from kt performance with PHP canned tunes pretty much and on the 140 tune I get no black smoke under throttle, now I would imagine this is normal with stock injectors because im sure the turbo can keep up somewhat. But the problem is I only make 16 psi max so shouldn't I be dumping black smoke? I know the low boost is because I have a hole in the intercooler pipe next to the power steering pump, but do I have low fuel pressure? I would imagine with only 16psi all the fuel will not be burnt. Hpop can hit 2800 and hold 2500. But ipr hit 80% under full throttle at 3k rpm and had trouble shifting but other than that never sees over 45%. I want to know whats going on with the fuel not boost, just to clear things up. And I don't really feel any power loss im stock. 99 f350 7.3 4x4 long bed cc
And just to be clear I am NOT trying to Roll Coal but a nice smoke trail when flooring it past people who cut you off would be nice
I believe I am having spooling issues with my 2000 f250 7.3 automatic truck. I now am running a 67mm billet compressor wheel with a 1.00ar turbine housing and high flow outlet so basically a thrust bearing 38r . I'm running oem sticks and PHP tunes on my hydra. On the 140 tune egts top out at 1200* uphill. So egts are not a problem. Boost tops out at 29-30 psi and 1-3 down the interstate. I see a lot of trucks that can hit 20+ psi in second by just squashing the skinny petal and I could also do this with my oem turbo. Mine takes awhile to get psi up like I said it will hit 30 if I'm petal to the carpet for a few and get going but I feel like it's not spooling as quickly as it "should ".
I completely built this turbo with new parts nothing was reused down to the heat shield behind the turbine wheel inside the turbine housing. I used all American And Canadian built parts . 360 thrust and a banks 1.00 turbine housing. When I bought the turbine shaft and compressor wheel it stated that they where pre balanced and I could clearly see the balancing marks on both but the shaft and compressor wheel are from two different manufacturers so there was no way to be sure that everything would align and be balanced. Basically my question is do you think it would to be wise to have the assembly balanced? Could this be the reason the turbo doesn't spool as fast as my oem gtp38 did . I've been running the turbo for four months now .
I've had this 01 7.3 for a few months now. When I first purchased I dropped new battery's, couple glow plugs, and wire harness going to the Pass side valve cover. it has 150k on it and an Edge tunner.
My first problem was about 2 weeks ago, it was raining and i was making a turn at about 5mph And all power shut off. I put it into park cranked 3times started up and the tuner stayed off for about 3minutes. I ran to auto zone and picked up a cps (I've recently found that oem is the only way to go?)
I made a trip about 2hrs locked the CC in about 70mph and the boost was going well over 12psi. this seems crazy because i usually dont get it over 4psi. I drive it with a light foot. on my way home i was pulling a trailer about 8000lbs load driving about 5mph out of the lot it shut off again. Started right back up and made the trip home fine. With the exception of the erratic boost.
Yesterday it shut off at about 40mph and turned back on its own. I am not throwing out a lot smoke doesn't have problems starting, I did a once over on the wire harness's and nothings jumping out to me.
So I just put billowed up pipes and changed the broken O ring in the turbo housing. Put everything back together and checked for a boost leak with the home made tester. Boots and everything ARE OK. I can hear air escaping from what seems to be the valve cover or intake. I realize that I am charging my crank case as well but it still concerns me that air is escaping from somewhere besides the CCV. I read the following forum and this guy had the same issue and after he found out he was charging his crank case he was no longer worried. . . . .
View 12 RepliesI guess it would be classified as very intermittent but in the past year I have had 3 separate times when my truck has after a short drive suddenly had zero boost..
Pull over and turn it off for 30 sec or so and all is fine. Cycle the ignition faster than that and issue persisted. It has only happened in colder temps. In all the reading I have done on FTE I've not come across anything similar.
Alrighty let me see if I can get everything. 01 6speed 450hp at rear wheels. Comp 910 valve springs, valve seals, 238-80% injectors, full RR, 38r turbo, napa air filter, Hydra with Gearhead tunes, 5"exhaust, 280k about 100k on rebuild. All mods done 40k ago. Now I have a horrible up pipe leak I assume is causing the low boost #'s I have to do another clutch so up pipes will be fixed when tranny is out this week. But I'm using 1-2 gallons of oil every 3k or so. I smell burning oil when I get out, mainly if I am getting on it then stop. I haven't pulled the fuel filter to see if its a injector o ring. (Tonight's project) but turbo sounds fine, I'm going check for shaft play tonight. What could be my loss of oil without it actually leaking on the ground?
View 14 RepliesI have done some searching on this, seen a video on YouTube but haven't read anything that is firm on what it is. We pulled our 5er for the first time last weekend and the chatter was pretty pronounced in the Arbuckles here in OK. I was running around 65 mph when I hit the largest hill and as I was climbing my speed naturally dropped, boost was around 17 - 18 psi when the chatter started.
Is it something to be really concerned about? Is there anything to be done to prevent it? I'm pretty much still stock, only deletes have been airbox to 6637, and I deleted the heater by turbo for the boost gauge. Other than that everything on truck is still stock.
I have an issue with my 6.0. I was running the extreme street tune from IDP for the past 2 years now and recently purchased the xtreme X tune from IDP. I loaded in the tune and had low boost, low power and horrible acceleration. Max boost i would see is about 10psi and it would take about a solid minute to reach highway speed when merging on the highway. I went back to the stock factory tune and have the same issue. No boost leaks from the boots or pipes and no check engine light. What is going on?
View 2 RepliesI bought a 99 f350 truck. it has a van turbo and exhaust back pressure delete. The truck wont make more than 3 PSI of boost. Ive got a p1690 wastegate actuator circuit code. unplugging the waste actuator does nothing. With the van turbo, is the actuator required? Is this code stopping the ecu from fueling and creating boost? I did a cylinder balance test, and cylinder 8 failed. Is a single injector not quite balanced enough to make it not boost past 3 psi? The turbo appears brand new (previous owner said it was), charge pipes hold pressure (tested), EBP Sensor tube is clean (shows up to 24 psi). I tested the wastegate actuator, OnDemand5 says if its over 50 ohms, its bad and replace it. its 69.5 ohms. Again, i dont want to replace it if i dont have to, as its not being used (no wastegate on van turbo), but if the ecu is preventing it from spooling because of the solenoid, ill change it.
View 14 Replies2000 truck, 334k, automatic 2wd, stock. Have low power, 11psi max.
Permanent p0472 code, can't clear it even temporarily. The moment I turn the key to Acc, code is there. It's the only code showing on Forscan.
Tried 470ohm 1/2watt resistor, in two turbo pedestal sensor connector wires, no change. Forscan shows 0.0-0.6 psi EBP value when running.
No change with pedestal sensor plugged or unplugged. Resistor or not. Truck starts and runs good, low power is the only issue.
Sensor and tube are new. Seems like wiring is bad, where to look next to track this down?
I've got a 2002 Excursion which has been giving me a little trouble lately. I've got a DP tuner, 4" exhaust, afe stage 2, and gauges (boost, trans temp, EGT). I've been running these for about a year now without any truck problems until recently
So I noticed over the past couple weeks it has gradually been taking longer for the engine to start. Started off by just having to turn the engine over a few more times. Now it has turned into having to turning over the engine for a few seconds, then turning it to off, then trying again. It always starts on the second attempt to start my truck and sometimes really hard where it blows out a little black smoke.
Not sure if this is a correlation to the problem above or not, but I've also been losing boost pressure, and I'm not sure when this started since I haven't been on the highway for a while. I noticed this because this weekend I drove on the highway and saw that I was blowing some black smoke every time I accelerated which has never been the case.
So I check my boost gauge and see that I'm sitting at like 3-5psi when I used to be at around 10psi+. I also noticed when I accelerated the boost pressure would increase like normal but then quickly drop once I stopped accelerating which is unlike anything I've seen before in my truck. I don't seem to notice a huge difference power or throttle response, but then again 95% of the time I'm driving under 40 mph to get to work. So this problem could have started the same time as the starting problem, but I can't say definitively.
What this problem could be, what to check or test?
I'm relatively new to the 6.7 engine , I have a 2014 F-350 SRW with aprox 51,000 miles on it. Normal driving I see about 8 to 10 psi of boost even under moderate acceleration although at times it will go to about 18 psi at WOT and it does this with heavy loads. At moderate acceleration the boost will jump to 10 psi quickly but immediately stop there and sometimes as the RPM"s increase boost pressure decreases. Only issues I have had with the truck was a clogged EGR cooler.
View 2 RepliesI understand how the waste gate is supposed to work at high rpms / boost.
I believe that as long as I keep the max boost down, that I can run with the waste gate plugged in order to goose the power a little in the 2000-28000 RPM range. Since the truck is stock and there's no intention of running higher RPMs, it seems like plugging the waste gate is a good idea. I just want to make sure that I'm not missing something.
It appears that the wast gate also opens when at idle and possibly when you let off the throttle. Are these important functions of the waste gate as well?
Here's a chart showing waste gate operation...
ive noticed my boost has been going down lately. At first I thought it was a boost leak so I replaced all the intercooler boots and both sides of the intercooler pipes. That diddnt change anything at all. I recently got new injectors (200/30%) and a hydra tune for them and it was quick the first few days i was running with that setup, my boost has been dropping and currently at WOT I can't even get to 10lbs of boost and it is noticeable driving, it's slower than it was stock. There was no play in the shaft of my turbo and the turbo in there is only 2 years old. Could the turbo be bad already? Or is there anything else I can check before buying a new one. I have an upgraded hpop and the 6637 intake.
View 13 Replies