Ford 7.3L Power Stroke (1999-2003) :: Truck Won't Start / Loud Click On Passenger Wheel Well And Then All Electric Completely Dies
Oct 13, 2015
Just tried putting a ts6 on my pcm. First time I hooked it back up I just got cranking with no start. So I pulled the pcm terminals really well plugged it back in and got nothing. I do not remember because I was kind of in a hurry if I unplugged the batter cables and back on the second time. I plugged it back in after cleaning terminals and went to start and got nothing. A loud click on passenger wheel well and then all electric in truck completely dies. I hope I didn't fry my pcm. Maybe just blew a fuse or starter relay?
View 6 Replies
Advertisement
I have search youtube and only found front door lock replacement but not the rear..
How do you go about removing the bad rear passenger side door lock actuator ??
View 14 Replies
I know there are a few threads floating around regarding truck dieing, but mine is slightly different than the others, maybe its the same culprit, maybe not, but i thought i would start a new thread just in case.
First, I commute about 50 miles to work everyday, truck gets plenty of interstate highway run time, smooth as silk. About a month and half ago when i almost got to work I slowed to stop at a red light. As I came to a stop the truck "stumbled". Acted like it wanted to die but caught itself and kept going. I said whooaaaa girl, what this? Ive had this truck for almost 10 yrs now and never anything like this. About a week or so later, same commute, same red light, cept this time it dies. Starts right back up no problem. Just acted like someone turned the key off.
Then a week or so after that, while driving home this time, as I pulled up at the house to check the mail at the mailbox, when i came to a stop it died. Cranked right back up. Before I could put in drive, it died again. Cranked right back up and i drove on into the driveway. Then a few days later, while checking the mail again, it died again. Cranked up immediately and parked.
Today, while driving home, after i had gotten back to town, but before i got home i made a stop at bank drive thru, when i came to a stop, it died. While cranking it wanted to start and kind of stumbled on itself and died. Then it cranked right up and i came on home no problem.
So far it only occurs after approx 45min to 1 hr of operating time so the engine and everything else are at temp and far from cold. After reading thru some of the other threads of similar but different conditions (cold start dieing, dieing while under power, etc) Im getting flooded with ideas of what could cause it, but not settled on any.
1.Could be failing ICP? (original, has never been changed, 317k+).
2.Could be plugged fuel filters? (been a while since changing, approx 30k+)
3.Could related to one of my own earlier threads regarding possible failing alternator (when rpms drop can volts drop enough to kill engine?)
4.Could be loose ignition switch? (about 2 yrs ago i had to swap the blinker switch, to get to it had to remove the ignition. Upon re-installation the switch never did get tight as before and was loose. Been loose ever since. To the point that with key out of ignition and door ajar i will get the door chime as if the key was in ignition. I can bump the ignition, and chime goes away. Been this way for two years and no apparent problems. Until now maybe?)
I was thinking ICP after a few of the other threads, but after tonight Im leaning towards the ignition switch. I guess i can try to wiggle the switch after cranking tomorrow and see what that does for a trouble shooting effort. Is there a way to trouble shoot the ICP to see if its failing or not? Isn't that a fairly costly sensor? Would hate to buy one and not be the cause, but after 317k i may need to buy before too long anyway.
View 5 Replies
I have a 99 7.3, I took off driving the other day and after about 10 minutes the truck just dies like I shut the key off but everything was still on. I tried to restart it and it would fire for just a sec then die. I set for about 15 minutes and tried again it fired up and ran about 5 mins then the same thing. I had a buddy hook it up to his scanner and it has a p0605 and another icp code.. We changed the icp then erased the codes.. Ran some rest through the scan took with the truck running and no codes so we took it for a drive made it about 20 minutes away and same thing but this time has the p0605 code again. Could the pcm be bad? I also noticed the electric pump is always on all the time it will cycle at least 30 seconds every time the key is turned??
View 14 Replies
I've been working on my truck for months now on and off. I thought i finally had it back, but i have (again) problems with running. it basically only ran for a full day (hauling trip) after getting it back up and running. next day, it died on me on the road.
The new deal right now is that I can make the truck start and it will run, but it has little "hiccups" or misfires that will happen every now and then. Once it gets warm enough, the idling sounds chopped (best way i can explain it). After "chopping" it will then run fine (until the next chop). then it seems that once the truck gets warm it just stalls out. When that happens (shutting off) i can't get it to start right away. i have to wait awhile before it'll start and that lasts only so long.
The truck puffs a tiny bit of white smoke. not constant but more like a "puh - puh - puh" ....I've changed out quite a bit of used up parts now...
Turbo
Injectors & wiring harness
valve seals
IDM
ICP
IPR
CPS
MAP
fuel pump
vacuum pump
glow plug relay
starter relay
All the sensors are OEM. There's fuel in the fuel bowl, and the filter is clean. Plenty of oil in HPOP & oil level in crankcase is good. Have plenty of fuel.
Air filter is clean and fine. No codes. No lights.
2001 f350 7.3 320k on it.
View 14 Replies
I am at a loss on what this could be. For the past 8 - 9 months my truck will randomly miss and if I am going slow enough it will cause the engine to quit but only when it is raining. I sometimes get a service light when it happens but as soon as i turn the key off and back on it goes away. My truck runs perfect otherwise and even when it rains except when it randomly does what I just explained.
This started when I replaced my passenger side valve cover gasket and I also took out my "brain box" (don't remember what it's called) and put it back in (didn't replace it). I did have the up-pipe replaced as well around the same time and put in EGT, boost and trans temp gauges. That's about the only things engine compartment wise that's been done.
I did just take it to a shop to put on a scanner and after his testing it did spit out 1 code. It was the cam position sensor. Can this sensor cause what I have explained? Like I said, this only happens when it rains. Doesn't matter if it's poring or barely sprinkling.
View 7 Replies
I have changed pickup filter in tank and cleaned 2 tube filters in tank i thought that would fix it.
View 3 Replies
Like the title says my truck has been stalling while driving. Accelerating or cruising it dies for a second, two at the most, and then just keeps chugging along again.
I thought i'd fixed the problem last year when I did injector O-rings and 50 cented my UVCH. It hadn't done it since, until two days ago. Started out with a two good solid stalls while gently accelerating up hill. I had thought maybe my fuel pickup foot had finely given up the ghost because I was below a quarter tank. But I filled her up full, and then she did it again about 50 miles of driving later.
I didn't catch the first four stalls on my torque app, because I'd just recently decided to stop logging every trip, with the thinking that it had been half a year problem free, why keep logging waiting for something that isn't going to happen. I did catch the 5th stall on the torque log. But I'm having trouble trying to figure out where it happened in a 30 min log.
First question where would yall start in tracking this thing down? Next what data actually should be logged? I think I've got some extra stuff in my logs that isn't necessary, and is maybe bogging down the system. I get one data point per second resolution on my logs. Are there ways to improve the resolution, will getting rid of some PIDs work?
Lastly I need to attack this thing smartly, without throwing time and money at unneeded parts. I had surgery and I've been out of work for 3 months and I'm looking at another 6 before I'm making money again, and there is no unemployment for the self employed. Also I only get 3-4 light weight upright hours a day to work, exceed that and I'm back on the couch battling swelling for a week.
Also is there anything I can do while driving to "flag" the stalls so I can find them more easily in the logs?
View 14 Replies
Truck starts great, and runs and idles fine until it warms up. This could be 15-20 minutes of driving or idling. Then it just dies. Like dead dies, lose power steering, everything (ac and lights still work, but no engine). It had died while idling, it has dies while cruising at 45mph. Then it will crank but no start. After about a 45min to an hour it will start like there was not issue, and pretty much drive the rest of the day (even after sitting) with no problem.
I installed the Adrenaline a few months ago, but the truck ran great for quite a while before this problem occurred. I did have it shipped with a rebuilt IPR. Tonight, I rebuilt the IPR with Guzzle's kit, and stripped it all the way down. Truck died again.
I have not had my AE hooked up when it died (stupid me today). But afterward I have been getting a few codes: P1283 (IPR Control Circuit) and P1212 (ICP lower than desired Engine crank or run).
When trying to start ICP duty cycle is about 64% and pressure is 185 to 190. If I unplug the ICP sensor pressure jumps to 2000ish, truck turns over faster and ICP Duty cycle goes to about 35%.
View 14 Replies
So I bought a Lifted 1999 F250 a couple weeks ago and last night the thing wouldn't start. The battery connections are not perfect but there's power going to the truck because it will give me the wait to start light and all. When I try to start it there's one really loud click and certain lights like the clock momentarily turn off when it clicks. Tried hitting the starter didn't work. Tried putting a jump pack to the starter and it didn't spark like expected.
View 8 Replies
Early 99' model I picked up. Blew the oil cooler and had lot of pressure in the Degas bottle, so did head job and oil cooler and now I'm Still getting a P0264. Unplug #8 injector truck almost dies, plug it up and she smooths out...
View 7 Replies
Alright so I have a 99 7.3l. One day I went to start my truck and when I turn the key to the on position all is normal and then when I turn it all the way to crank it nothing happens. I hear a relay click ann thed that's it. Me and a buddy of mine spent quite some time on going through the entire truck. The starter was replaced, the neutral safety switch was replaced and the ignition switch was replaced yet the problem is still there. We then discovered that fuse #20 under the dash keeps blowing with every turn of the key. The manual states that this fuse is a starter motor relay coil PCM ( gasoline only). So if it's gas only why is it even in there. Let me just say that I can jump the fender mounted relay and the truck starts.
View 7 Replies
My passenger side wheel bearing is going out. I had a local company replace it under extended warranty 7 years and 90k miles back. I think I have gotten pretty good life out of it. I think it was from Napa but not positive. I try to grease then once a year but I'm not always successful.
View 14 Replies
I've done everything I can think of, ive replace the starter, batteries and altenator, both batteries have at least 12.30 volts when taken out and checked, but i turn the key and it will have power then try to start and whole system dies and wont come back on, I've cleaned the terminals and posts to shiny and the ground connections but its still not getting power.
View 1 Replies
2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
View 14 Replies
My brothers high mileage 7.3 ran out of gas because of a broken fuel pick up line. I brought him 10gal fuel, primed out of it and now the truck is sputtering and sounds like it's running on 2 cylinders. It's not just air in injectors or something it sounds like crap. It's getting fuel at least to the bowl.
View 14 Replies
This past weekend I noticed I was loosing boost pressure on my 2003 7.3l F250 so I pulled my turbo out found the problem fixed it then put the turbo back in. After it was all said and done I went to start the truck up and it just cranked and cranked a cranked but no start. Worried I didn't hook something up right I checked and rechecked everything to do with the turbo, all good nothing out of the ordinary.
I tried to start again, nothing. Spent all day yesterday trying to figure this out. Replaced the cps still nothing. No movement in tach but I don't remember any on startup anyway. Drained the fuel filter had adequate pressure and such but replaced the filter anyway. Still nothing. Checker all my fuses, one by on and non were blown but I still tried disconnecting my fuel bowl heater and still got nothing. I tried disconnecting the Icp still nothing. There was no oil around the icp either.
I'm getting frustrated that the truck wont start, the truck ran perfectly fine before the turbo removal but now wont even give a sign of kicking up. Just cranks and cranks. Also checked Hpop to see if that's the cause and it's filled like to the brim. But when I'm cranking the truck about 10 sec into the oil pressure gauge kicks up and reads good but only when cranking.
View 7 Replies
I bought this 16' box truck today. 7.3L, 213k, 2003. It doesn't start and the owner gave a really good bottom dollar deal for all these reasons. Showing up armed with Torque Pro and my bluetooth adapter, I proceeded to plug it in and check for rpms, HPOP, Battery voltage, etc. No power to port
Find fuse diagram the owner located and fuse 23 is the OBD port. No fuse in place. He found us a fuse, I plugged it in, viola! Power to the port, TP is in action, ready to troubleshoot.
"Charged" battery, start cranking...no start. No Torque Pro (!) Apparently, the OBD port is cut-off while cranking .... Is there some other fuse or connection that will keep it connected during cranking so I can check for RPMs (no dash gauge for it)?
As soon as I left off the starter, the HPOP on TP showed 1212 then 850, then continued to drop with in about 2 secs. I figure it is getting good HPOP and this is the momentary bleed off.
PO replaced some time ago CPS with Autozone or something in an attempt to start it. No go. I am going to take my "emergency" CPS next time to see if that does it.
Because of the cranking-cutout, I cannot see FIPW. No way to know if the injectors are firing. It had reportedly been running a short time ago (weeks maybe?) and shut off while parked in the parking lot and never started again.
Batteries are low, but new-ish starter and cranks well. With jumpers, able to maintain 10.8v or so while cranking, though it was a bit up and down. I'll take a strong charger with 200amp boost mode next time.
Fuel pump runs. I can feel/hear it when the key is cycled. It has standard Rotella 15w-40w on this 50F day. Reportedly *wants* to be plugged in to start. I plan to switch to 5w-40w synthetic as soon as I can get it home.
It's automatic, pretty sure all van/stock. Here's a pic. Dog box gives good access to turbo and such, but everything else...
One battery under hood, other under cab/body. Has green antifreeze and leak at thermostat.
My goal is to get it running to get it home, about 30 miles, then replace ICP, CPS, IPR, Glowplugs (relay already done), thermostat and top housing and hose, convert to lifetime antifreeze, oil change to 5w-40w synthetic, 2 batteries (test alternator), uppipes or gaskets, Air filter (what upgrades available for this?), UVCH, idler pulleys and belt, replace trans fluid and filter, couple tires, paint inside box, weld and reinforce rear bumper, add radio, check cigarette plugs (think cell phones and gps), general cleanup.
I will have it and run it around 30 days. If it is solid and reliable, off to West Virginia it goes. If not, I'll part it out to get back what I can from it. I am paying for it up front, they are raising donations. But I won't let them pay anything (costs only) for it until I'm satisfied.
They need to run it about 5hrs round trip once a month immediately. That's about 3k miles per year. But I'm sure they will find lots of other uses, such as building supplies, etc. I'm hoping the injectors hold up for a while.
Right now they have multiple vehicles, trailers, drivers donating their time and vehicles (reimbursed for fuel only). It would be much better to take one hauling truck and one or two passenger vehicles... hence the box truck idea.
They distributed approximately 100k lbs of food last year. Not refrigerated, not needed. No CDL needed, about 14k GAVW. The PO has offered his carport where it is parked now, or even to push it into his garage with limited tools (I can bring some) to get it to run. Otherwise...
How to get this home?? Too heavy for my buddy's tow truck from the front. Wheels too far from back of box to reach them from the rear. No tow loops in front for tow bar, UHaul dolly rated at 4k (maybe?)
Dual rear wheels. Anything else I'm missing?
View 14 Replies
Truck cranks wont start. Fuses and relays good, New motorcraft; IPR, ICP with pigtails, New T500 hpop, New 180/80 Injectors, Push rods, 910 valve springs, Mellings lpop. Motorcraft oil cooler.
Reservoir full, oil new 15-40w Amsoil, Rails full, Fuel bowl full and clean, HPOP drive gear rechecked and torqued.
RPM 180
Temp oil 88*
ICP duty cycle koeo 14.8, crank 64.85
ICP pressure 250 -450psi
ICP voltage .27-.50
Manual gauge on oil rail 250 -450psi when cranking
Inj pulse width .0005,
Buzz test was good
Vref 5v all sensors. 12v at IPR w/koeo
Fuel pressure 58psi
Air test hpop hear no leaks with stethoscope.
DTC codes: P1280, P0380
Also put straight edge across injectors to double check they were seated.
View 11 Replies
Ok truck would not start when cold outside. So I put a gpr on truck. Truck alt would only put out 11.5 ... After I put it on. So I put 4 new alts on all read the same 11.5 and the battery's would drain over night. Turns out they gave me a starter relay. So I have the proper one now. Now when u turn the key the everything is flashing the dash dome light buzzer. But take one of the small wired off the gpr, it stops but I have no power to the starter. It's been 2 months of hell trying to figure it out.
View 14 Replies
I have a 2000 7.3 f450 having some electrical issues. When you turn the key on sometimes the dash will start ticking and left side light flashing...engine will turn over but it won't start. The ticking is coming from under the hood relay 32 (you can hear and feel it clicking). Book says its injector driver module power relay. A lot of the times it will start fine other times it will be running and just die (prob because of this issue) happened once when I was driving.
What to check here already replaced the relay still have the problem.
View 6 Replies
