I bought a 99F350 with a 7.3, it was not running when I bought it. Batteries good, new starter, turns over just fine, fuel pump works, but now I don't know what to look for.
Was testing ohms for my injectors and at the plug on top of the driver side valve cover, couldn't get a reading at all, tested the ohms at the pass. Side valve cover plug and got good ohm readings.
Truck is a e99 f250sd 4x4 7.3 manual trans. The truck started and ran fine to work this morning. Went to leave this afternoon. Hopped in, put key in and tried to start it. Engine just turned over, never started. Thought that it didn't start because I didn't let the plow plugs warm up enough. Turned ignition off, turned back on and let wait to start light to go out. Same thing happened again. Just turned over but wouldn't start. As far as I can tell the fuel pump is running. Felt it vibrating while the ignition was on. What to check.
View 14 RepliesGot up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
It's a 99 f350 7.3 diesel powerstroke. About 180k miles I think.
It cranks fine. I just changed the glow plugs(all were dead) but when you try and start from cold, it takes about 7-10 seconds to fire. The oil res is full, tried disconnecting the EOP sensor, still fires up and takes just as long. There is one near the oil filter, and that seems to not be it either.
Doesn't smoke, no oil leaks that I know of. Not sure what else to check before sending it to another shop to get put on a diagnostics machine. I read about the IPR, but it has no problems when running. Only problem is a very long time to start. Also changed the fuel filter.
2002 Excursion, 7.3L 375,xxx miles ... As the weather is cooling off, my excursion has a starting problem for a few years.
Replaced all the glow plugs last year. We (my brothers and I) thought it was injectors, but in the summer time or if block heater is plugged in, she starts normally and idles smoothly. And no smoke and runs fine once she warms up.
When cold, it acts like 1 or 2 injectors are not firing. Have run all kinds of cleaners through the oil and fuel.....
Don't want to swap injectors just to swap parts. Would like to diagnose problem....
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 RepliesMy brothers high mileage 7.3 ran out of gas because of a broken fuel pick up line. I brought him 10gal fuel, primed out of it and now the truck is sputtering and sounds like it's running on 2 cylinders. It's not just air in injectors or something it sounds like crap. It's getting fuel at least to the bowl.
View 14 RepliesThis past weekend I noticed I was loosing boost pressure on my 2003 7.3l F250 so I pulled my turbo out found the problem fixed it then put the turbo back in. After it was all said and done I went to start the truck up and it just cranked and cranked a cranked but no start. Worried I didn't hook something up right I checked and rechecked everything to do with the turbo, all good nothing out of the ordinary.
I tried to start again, nothing. Spent all day yesterday trying to figure this out. Replaced the cps still nothing. No movement in tach but I don't remember any on startup anyway. Drained the fuel filter had adequate pressure and such but replaced the filter anyway. Still nothing. Checker all my fuses, one by on and non were blown but I still tried disconnecting my fuel bowl heater and still got nothing. I tried disconnecting the Icp still nothing. There was no oil around the icp either.
I'm getting frustrated that the truck wont start, the truck ran perfectly fine before the turbo removal but now wont even give a sign of kicking up. Just cranks and cranks. Also checked Hpop to see if that's the cause and it's filled like to the brim. But when I'm cranking the truck about 10 sec into the oil pressure gauge kicks up and reads good but only when cranking.
I bought this 16' box truck today. 7.3L, 213k, 2003. It doesn't start and the owner gave a really good bottom dollar deal for all these reasons. Showing up armed with Torque Pro and my bluetooth adapter, I proceeded to plug it in and check for rpms, HPOP, Battery voltage, etc. No power to port
Find fuse diagram the owner located and fuse 23 is the OBD port. No fuse in place. He found us a fuse, I plugged it in, viola! Power to the port, TP is in action, ready to troubleshoot.
"Charged" battery, start cranking...no start. No Torque Pro (!) Apparently, the OBD port is cut-off while cranking .... Is there some other fuse or connection that will keep it connected during cranking so I can check for RPMs (no dash gauge for it)?
As soon as I left off the starter, the HPOP on TP showed 1212 then 850, then continued to drop with in about 2 secs. I figure it is getting good HPOP and this is the momentary bleed off.
PO replaced some time ago CPS with Autozone or something in an attempt to start it. No go. I am going to take my "emergency" CPS next time to see if that does it.
Because of the cranking-cutout, I cannot see FIPW. No way to know if the injectors are firing. It had reportedly been running a short time ago (weeks maybe?) and shut off while parked in the parking lot and never started again.
Batteries are low, but new-ish starter and cranks well. With jumpers, able to maintain 10.8v or so while cranking, though it was a bit up and down. I'll take a strong charger with 200amp boost mode next time.
Fuel pump runs. I can feel/hear it when the key is cycled. It has standard Rotella 15w-40w on this 50F day. Reportedly *wants* to be plugged in to start. I plan to switch to 5w-40w synthetic as soon as I can get it home.
It's automatic, pretty sure all van/stock. Here's a pic. Dog box gives good access to turbo and such, but everything else...
One battery under hood, other under cab/body. Has green antifreeze and leak at thermostat.
My goal is to get it running to get it home, about 30 miles, then replace ICP, CPS, IPR, Glowplugs (relay already done), thermostat and top housing and hose, convert to lifetime antifreeze, oil change to 5w-40w synthetic, 2 batteries (test alternator), uppipes or gaskets, Air filter (what upgrades available for this?), UVCH, idler pulleys and belt, replace trans fluid and filter, couple tires, paint inside box, weld and reinforce rear bumper, add radio, check cigarette plugs (think cell phones and gps), general cleanup.
I will have it and run it around 30 days. If it is solid and reliable, off to West Virginia it goes. If not, I'll part it out to get back what I can from it. I am paying for it up front, they are raising donations. But I won't let them pay anything (costs only) for it until I'm satisfied.
They need to run it about 5hrs round trip once a month immediately. That's about 3k miles per year. But I'm sure they will find lots of other uses, such as building supplies, etc. I'm hoping the injectors hold up for a while.
Right now they have multiple vehicles, trailers, drivers donating their time and vehicles (reimbursed for fuel only). It would be much better to take one hauling truck and one or two passenger vehicles... hence the box truck idea.
They distributed approximately 100k lbs of food last year. Not refrigerated, not needed. No CDL needed, about 14k GAVW. The PO has offered his carport where it is parked now, or even to push it into his garage with limited tools (I can bring some) to get it to run. Otherwise...
How to get this home?? Too heavy for my buddy's tow truck from the front. Wheels too far from back of box to reach them from the rear. No tow loops in front for tow bar, UHaul dolly rated at 4k (maybe?)
Dual rear wheels. Anything else I'm missing?
Truck cranks wont start. Fuses and relays good, New motorcraft; IPR, ICP with pigtails, New T500 hpop, New 180/80 Injectors, Push rods, 910 valve springs, Mellings lpop. Motorcraft oil cooler.
Reservoir full, oil new 15-40w Amsoil, Rails full, Fuel bowl full and clean, HPOP drive gear rechecked and torqued.
RPM 180
Temp oil 88*
ICP duty cycle koeo 14.8, crank 64.85
ICP pressure 250 -450psi
ICP voltage .27-.50
Manual gauge on oil rail 250 -450psi when cranking
Inj pulse width .0005,
Buzz test was good
Vref 5v all sensors. 12v at IPR w/koeo
Fuel pressure 58psi
Air test hpop hear no leaks with stethoscope.
DTC codes: P1280, P0380
Also put straight edge across injectors to double check they were seated.
Ok truck would not start when cold outside. So I put a gpr on truck. Truck alt would only put out 11.5 ... After I put it on. So I put 4 new alts on all read the same 11.5 and the battery's would drain over night. Turns out they gave me a starter relay. So I have the proper one now. Now when u turn the key the everything is flashing the dash dome light buzzer. But take one of the small wired off the gpr, it stops but I have no power to the starter. It's been 2 months of hell trying to figure it out.
View 14 RepliesOk I'm working on a 2000 7.3 on a F550 truck was running but had no power so we changed out all the injectors and glow plugs and rebuilt the turbo now there is no start it turns over and were getting black smoke from the tail pipe. What is going on with it?
View 2 RepliesThe first has I replaced my tranny with a stock 4r100 tranny and torque that only has 75k on it. The guy was doing a 6-speed swap. After I had the tranny and torque converter and a new tranny cooler installed, the tranny shifts real hard. I think it may be from my DP Tuner. Even on my economy tune driving it very easy sometimes, it jolts into gear pretty good.
I was wondering if I could just get a shift kit to maybe correct that and if so if I would have to drop the tranny to install the shift kit. I saw a bully dog kit for like 75 bucks, however, I don't really have the money to have the truck in a shop and I would really like to not drop the tranny and not lose all my tranny fluid if possible (very expensive).
Also my other issue, the truck in warm or cold weather is very hard to start. Half of the time it takes two tries to start it. It will crank and crank and no go. Then the second try it fires right up. It has two new batteries, where do I start? Is it possible that the starter is just getting old or is it fuel or oil pressure related possibly?
So I have a 2001 f250 7.3l and on my way to work yesterday while driving down a hill I switched my ts 6 switch to 140 and it immediately stalled, so I pulled over and restarted the truck and it started up fine and I drove the rest of the way to work, I go to start it after work and it won't start, it just cranks and cranks and cranks, occasionally it'll fire and I got it to start and was able to rev it for about 30 seconds but then it died, disconnect the 6 position switch from the idm and tried but still nothing.
So today I replaced the ipr valve, got everything back together still won't start maybe a little worse now, I know it's getting fuel cause there's pressure in the bowl when I try to take it off, there's a new icp valve, cps, new fuel filter and new sending unit, the hpop is topped off. Also I noticed when I went to change the ipr the wires on the plug were bare and touching so I addressed that, I don't know what else it could be?
So a few weeks back, i went to the store after work, came out and my truck just cranked and cranked but wouldn't turn over. I simply turned the key off and back on, waited for the WTS light to go out and she started up. I just blew it off, thinking i didn't wait long enough to start it.
Then, later that week i come out of a restaurant and it cranks and cranks but doesn't start. i tried turning the key off and on, waiting 30 seconds between em and still nothing. Then a few minutes later, i try again and she fires up, no problems and runs like a champ.
Well 2 fridays ago, I go out with some buddies, go to leave and it happens again. Cranks and cranks, but not starting. I got a ride to my place, grabbed a fuel filter, thinking maybe its clogged, it's been awhile since i changed it. I got back to my truck, and it started up fine, without changing the filter.
Then last night as i am out of town, 10 hours away from home it happens again. And i kept trying and trying and trying but it never wanted to start. I was about to submit my payment for the Uber back to my hotel when i decide to try it again and it fired right up.
Now I'm kind of afraid to drive anywhere and shut off my truck in fear of being stranded. What could be causing this? I've looked every where and havent found someone with the exact same problem, usually when i find a thread on turning over but not starting, the truck dies once it runs as well. Mine doesn't. when it starts, she runs great.
No smoke coming out the tail pipe when cranking.
WTS light comes on and off as it should.
Tach does not move, and it won't because it's a 2002.
Where to start, would the CPS cause it to act this way? It only seems to do it when the engine is warm.
As would be expected things deteriorate on a 16-year-old truck. My alarm has, on a few occasions, decided to annoy anyone around by activating for no apparent reason. This has happened in various conditions (in the parking lot, in the driveway, right after I've driven it, or sitting half the night). I chalked it up to aging circuitry.
Now I've picked up something new. Over the last few weeks my truck may or may not arm. It seems to be a flip of the coin. I'll drive to the store and I push the button on my remote and the truck goes "beep"..."beep". 10 minutes later I drive home, park the truck, push the remote, and the truck goes "beep"...and that's it. My alarm light is blinking two quick flashes when this happens.
Since this has started my truck has begun randomly having a delayed start. I'll disarm the truck, turn the key, and nothing happens for about 1 second or so (seems longer) then the truck starts normally.
Both of these issues started pretty close to the same time. I would normally go straight for a starter issue but I don't know if these might be related. I'm the second owner so have absolutely no idea about the Ford anti-theft system, how it's connected, or what the blinking lights mean.
I'm considering disconnecting the anti-theft system to see if that makes a difference but, as stated, how it's connected, what I might disable, or how it works. Was there any documentation published on it?
Background on the vehicle, Last week installed Swamps 200cc/30% injectors with a 38r. Had swamps reburn my chip for the new upgrades.
But heres the problem i noticed starting the truck was a little harder ( longer cranking ) till it would start never thought of anything since i read air gets in and can cause it but then yesterday and today its taken 30 minutes to start the truck since i have to do a trial and error.
The truck just seems like the batteries are being drained or something along those lines. i also noticed my gauges keep resetting back to blue( default color). Today I plugged a battery charger up all good voltage i charged them so both read 14v and still no start. So a couple of attempts at starting with chip in and ICP on nothing
I unhook the chip and ICP get a half start then eventually it starts. After then i can hook it all back up and it starts good for the rest of the day but for what ever reason after it sits all night it doesn't want to start up right away. I'd like to figure it out today since id rather not wake up at 4am and attempt to do this all before work each day.
I noticed that my gauges would reset to the default color after each turn off. So i unscrewed my ECU and then redid that to make sure its tight. along with making sure the chip is seated properly. after that it stopped resting my gauges. Whether that's the issue or not i cant say but ive been checking my HPOP oil level since i stopped driving it around 1400. and hasn't changed oil levels are good. I plan on starting it before I go to bed around 2200-2300 just to check and see what happens.
Alright, my 1999 7.3 keeps dying on me in the morning. About two weeks ago I noticed it started to have a weaker start up, even though it has two brand new batteries. Once it starts up, I get around the block and it dies there every time. Then I have to crank it for about 15 seconds for it to start again.
The crank gets faster and faster until it finally start, and the engine is very choppy, like its starving for fuel. After about ten seconds of that it return back to a smooth idle. I then take off, and about 50 yards later it does the same thing. After it does it the second time, the truck runs just fine for the rest of the day with no problems.
I have noticed that when if I turn the truck on and let it idle for 10 minutes first in the morning, it won't die on me. I replaced the camshaft position sensor thinking it was that, but it wasn't.
I recently bought a 2003 f350 7.3, I ordered a tuner for it and tried installing it, at one point while the ECM was still connected I did something and it sparked. Then the powertrain relay (302) started clicking really fast. It clicked in the on position. I switched it with another and it was also clicking. So since I sparke the ECM I figured I messed it up. I ordered another one and it's doing the same thing. Then I pulled fuse 45 (which was good) and put it back in. When I turned truck to on position it wouldn't click anymore, but it still won't start... What it could be? OV ruled out the ECM, powertrain relay (302) and fuse 45, I don't know what else to check.
View 2 RepliesI've tried everything I can think of to get my cruise control working again to no avail. I have a late 99 with a 6 speed. So far I have checked all the fuses with a multimeter, I've checked continuity from the harness under the dash through the clockspring to the switches, truck does not start without the clutch pushed in so the neutral safety switch works, has the upgraded switch and harness off the master cylinder. the previous owner said the cruise was intermittent about a year after they did the harness and switch recall on it. is there a way to test the harness and switch? I got a 1800 mile round trip coming up in about a week and I am gonna have a sore foot if I cant figure this out.
View 11 Replies