Ford 7.3L Power Stroke (1999-2003) :: Truck Not Starting When Cold / Would Not Crank Up
Oct 24, 2016
I had issues with my F250 cranking last winter when the temperature dropped, so I changed out the glow plugs in the spring. I hadn't been able to truly test them yet, since it hasn't been cold, but the other morning my truck wouldn't crank up. It was 40 degrees out the night before, and it had been almost 24 hours since I cranked the truck, but it seems to me like the truck shouldn't have an issue in that mild weather.
I'm not sure what I need to do next to try and fix this problem, it's been driving me crazy and risks stranding me if I park for a while in an area where I am unable to plug by block heater in. The truck cranks fine when I have had it plugged in for a while, so I'm fairly certain it's a heating issue. I haven't done any tests since last year, but I know that the GPR was working properly last winter, which is why I changed out the glow plugs.
View 4 Replies
Advertisement
2001 F250 7.3l 294k miles
Ok so truck has always had difficulty starting cold since I got it about 12k miles ago. Replaced glow plugs, that made things slightly better but still no start unless temp gauge was in that first line above the C. Changed to Rotella, immediately after oil change starts better and at slightly colder temps.
Since getting the truck when you turn the ignition on you can hear a 'whistling' type noise which I believe is the fuel system pressurising. That used to last as long as the chimes did when you first turn the ignition on. More recently it lasts a lot longer.
Towed recently and had intermittent check engine light - believe this could be HPOP related, haven't checked codes yet as we're on vacation. No oil in the valley. But I do have a little oil carry over in the turbo intercooler pipes.
Truck slightly sluggish at setting off initially and then picks up reasonably well when not towing but my Dyno says I'm putting a bit more pedal to get the same performance from say two months ago
Pretty sure injectors haven't been changed since truck was new but can't be absolutely certain as there is no history. I was surmising this is probably both a HPOP and injector age issue but only from what I've found searching...
View 14 Replies
Started truck 3 times in 30 min. no issues with truck before tonight nice well cared for truck. Went to get a pack of buns at store came out --NO CRANK--all lights are on dash, etc, new starter a month ago, relay changed out in fuse panel just to see if there was a change. Bought two new Motorcraft batteries installed , NO CHANGE, so is it natural safety, key switch, electrical ignition switch, solenoid on starter, is there a solenoid between key and starter?
View 12 Replies
I have a 2001 E-350 w/7.3. When I start the truck first thing or when engine is cooled down it starts fine. I checked the high pressure pump pressure and it is 500 - 600 psi start up great. But when engine warms and try to start it it has long crank before starting. I checked pressure and it is between 425 to0 450 and takes awhile for it to get to 500 or better. Is this a cause of the high pressure oil pump ? I changed the oil and still does same thing. Also I noticed that after engine is hot and I try to start it, while cranking the engine the oil gauge does not move. I don't know if it supposed to when you crank it or not. I thought on other 7.3's I've worked on that the gauge builds up pressure....
View 14 Replies
I have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
View 12 Replies
Have a 7.3 powerstroke won't start.. I have went through tons of parts check everything I can think of. I have put icp, our, fuel pump, fuel pump, injector, glow plugs and relay, fuel and air filter. new starter, new valve cover harness. HPOP is good and compression is good?
View 14 Replies
I want test my fuel pressure. What is a good gauge or kit to buy? My truck has lost power towing and is now starting to miss a little. I'm wandering if i my problem is in the tank. Is there a good scan tool that would diagnose things too?
View 14 Replies
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
View 14 Replies
I have an 02 f250 230,000, first 7.3. I've owned it since Oct and put less than 6,000 miles on it. I have another cold crank no start. New glow plugs and Glow plug relay last weekend. Worked fine that weekend. It sat all week, then crank no start fri night, it was like 70 degrees for the high that day. Plugged it in over night and it started. Did not fire right up cranked it for a couple seconds. I drove it all day, started every time. Valve covers have 5,000 miles on them. Fuel Filter heater fuse not blown. But don't know how to check it for sure. And don't know where to go with it from here. Getting frustrated with crank no starts. No troubles found.
View 2 Replies
So back ground is as such. Truck started fine before I replaced the hpop with t500 and did the driven diesel regulated return. I have double checked everything is plugged in. Now when I try to start it cold it will just crank. Yes I get smoke and oil pressure both places. If I give it a shot of ether it will start right up and run fine all day. What am I missing? Yes I know ether bad.
View 14 Replies
I have a 2000 F450 with a 7.3. I am having problems starting it. Batteries are good, engine turns over strong. It has started a few times after a extremely long crank (so long I am sure I am burning out the starter). I have replaced the CPS since it was cheap enough but that didn't make a difference. I have unplugged the ICP and it is very oily inside the connection. Does this mean the ICP should definitely be replaced? The truck will not start with the ICP unplugged. Should it be able to start with the ICP unplugged? Other items I plan on looking at at the IPR and possible the IDM box. Am I on the right track?
View 11 Replies
Alright, my 1999 7.3 keeps dying on me in the morning. About two weeks ago I noticed it started to have a weaker start up, even though it has two brand new batteries. Once it starts up, I get around the block and it dies there every time. Then I have to crank it for about 15 seconds for it to start again.
The crank gets faster and faster until it finally start, and the engine is very choppy, like its starving for fuel. After about ten seconds of that it return back to a smooth idle. I then take off, and about 50 yards later it does the same thing. After it does it the second time, the truck runs just fine for the rest of the day with no problems.
I have noticed that when if I turn the truck on and let it idle for 10 minutes first in the morning, it won't die on me. I replaced the camshaft position sensor thinking it was that, but it wasn't.
View 2 Replies
I have a early 99 f250 super duty 7.3l and it's giving me fits. about a month ago the truck started to do a hot no start. drove truck for about a hour. Shut it off and half hour later no start. Let it sit over night and would start with long crank.
Changed CPS no change. Pulled tuner and set back to stock. No change.
Changed fuel filter, no change.
After reading forums changed IPR and truck started and ran great. About a week ago back to the same problem. Battery's are about 2 months old. Oil change and oil filter a month ago.
Checked the hpop reservoir and its 1/2 from the top.
Checked fuel bowl and it has fuel. no sign of oil in it.
Drained bowl and watch bowl fill back up. seems to fill quickly.
Pulled passside valve cover to check for bad orings while cranking.
Every thing seems fine. have not done driver side yet. used FORSCAN and ran buzzed test on injectors and they all buzzed what seems to be about the same. ran test couple of times to make sure. this morning I ran a live scan while cranking and this is what I got right before it started. ICP 660.6psi, IPR 64.84% and RPMs 227. took 8.86 seconds to start. after work scaned again for hot no start and this what I got. ICP 292.9psi, IPR 55.86%. and RPMS 203. unplug ICP and no change. still will not start. one thing I did notice when plugging ICP back in I looked down in side at the pins and can see what seems to be bubbling around one of the pins. the pig tail has just the slights sign of oil.
View 14 Replies
For a long time I have been noticing extended cold cranks as compared to my dad's truck which has 50k less miles. Hasn't been much of a big deal until lately the crank has been getting longer to the point where it is noticeable and bothers me.
When the truck finally fires (10-15 seconds) it will sit and idle no problem, maybe a little rough, but that's about it. It will also run a little rough if you start driving it right away but will smooth out fairly quickly. When it first starts it is usually accompanied by a small puff of white smoke.
As a quick run down it has had the injector o-rings, glow plugs and UVCHs replaced about 36k ago. I can verify it isn't the glow plugs or the harness because it would start reliably down to -25 without being plugged in.
My thought is the injectors are just nearing the end of their useful lives (248k). Does this make sense?
View 14 Replies
Okay a little update on my truck not starting, and for those who have not read my earlier post. My water in fuel light has been on in my truck for probably a month of use. I drained the water sep under the truck nonstop and added several bottles of water remover and the light would not go out so I assumed the sensor was just bad. (im new to owning a powerstroke btw) I broke down coming home from work, got it towed home, and still cant get it started. It will crank fine just wont fire up. I tried unplugging the ICP, i replaced the CPS, and ordered a new water sep/ fuel filter for under the truck. And the fuel filter on top was just replaced a month before breaking down. Every single time i drain the separator tons of clear water diluted fuel comes out before it turns greenish.
Not sure if this could be a cause of getting water in my fuel but one time i filled the truck up completely and it was like the water overfilled and probably a quart or two of fuel spewed out onto the ground. Not sure where it came from. Also I have just over a quarter tank so i was thinking maybe the float broke and I just needed to add fuel but today before i went to add fuel i drained the sep and tons of water came out... Im so worried about hydrolocking my engine or ruining my injectors. But I dont know if my issue even is water related if the sensor just went bad...
View 14 Replies
When the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.
View 14 Replies
Ok truck would not start when cold outside. So I put a gpr on truck. Truck alt would only put out 11.5 ... After I put it on. So I put 4 new alts on all read the same 11.5 and the battery's would drain over night. Turns out they gave me a starter relay. So I have the proper one now. Now when u turn the key the everything is flashing the dash dome light buzzer. But take one of the small wired off the gpr, it stops but I have no power to the starter. It's been 2 months of hell trying to figure it out.
View 14 Replies
We're currently RV camping in the Wyoming Wind River Range at 8500 ft and is getting to freezing at night. The past two mornings the truck has been very difficult to start and I got quite a bit of smoke. This morning it took two or three tries but I got it going.
View 3 Replies
Got two brand-new Motorcraft batteries installed about a month ago and truck has been cranking great. However, the last couple days in the mornings the truck is starting slow and dragging as if the batteries are going bad. It does crank pretty quick but just has a noticeable starter drag now. Since I have no way of diagnosing the batteries with a tester over the holidays.
What are the odds that brand new batteries are going bad? I was thinking this is a starter issue since the drag is most prominent in the morning but it does it throughout the day while I'm driving driving on each start. But it's not as bad as the first start-up.
I hooked up a scan tool (Forscan and Dash Command) and the only trouble code I received that something to do with the turbo boost pressure fault, it was a code P1247. I don't see how a turbo boost pressure fault, low pressure, could have any starting related issues but you never know. Just a note this code only came up on my FORScan Lite app but it did not come up on the dash command app so I'm not sure if it's a legitimate code.
So I'm back to a battery or starter issue. Is there a way that I can check without much equipment to detect whether not I have a starter or battery problem. I do have a battery charger but no other equipment.
View 14 Replies
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies
I have a 2001 7.3 with 259,000 miles. It does not get too cold here, however over the past few winters when the temp is below 50 at night the first minute or two of running out of the neighborhood is tough going unless I let it heat up. It has been getting worse over the past few years and now if its even 55 or 60 I need to let it heat up. Glow plugs? Injectors?
View 3 Replies
