Ford 7.3L Power Stroke (1999-2003) :: Transmission Malfunction - No Gears At All - Won't Restart
May 4, 2015
Ok let's start I have a 1999 f350 7.3 4x4 Work Model that I'm have some odd transmission problems. I drove it 20 mins to do a 2hr job no problems finished that got in took off I few seconds down the road it was like the tranny just dropped out no sound just reved no gears at all. So I shut it down tried to start again would not start in park without pulling up on the lever which had experienced here and there for a good while. So got it started went in gear took off same thing went popped out no gears. I started it again this time used reverse same thing as drive so got it where I knew I could leave it but now it would not start in park anymore at all. Next day picked up a neutral saftey switch changed it now it starts in park every time but still starts going looses the gear then have no gears shut it down sometimes had to wait a few then again same issue.
View 14 Replies
Advertisement
I was pulling the I-40 ascent to Asheville today while empty, got to the top and started down the other side got to semi flat road and the tach suddenly went up about 600 rpm's. Transmission temp about 180*F. I let off, then resumed and everything was fine. About a mile later it happened again. This time the tranny lost 3rd and OD, still had 1st, 2nd, and Reverse. So, we limped into a service station. Temps hovered in the 170-180 range. At this point there are no codes, no lights, O/D is not flashing.
I shut the truck down to check fluid level and current condition. Everything was fine last night. Fluid level is still good and fluid is still red and clean. I changed fluid about 2k ago and the fluid coming out looked almost as good as the fluid going in.
Got back in the truck started it up, checked for codes and got a P0705, put the truck in gear to get to a diesel shop down the road and everything was fine, shifted completely normally through all the gears. This lasted until about 1 mile from home and then the same thing happened all over again. Fluid still looks clean, not burned, still no CEL, no flashing O/D, but only have 1st, 2nd, and Reverse.
View 14 Replies
I bought it 4 years ago with 205K, swapped trans fluid.. 10k miles later (I don't drive it a lot ). I am throwing the code P0750 Shift A malfunction.. i figured id swap the solenoid pack since I am pretty handy and it was affordable.. but it didn't seem to do the trick.. it drove around the block good for 5 minutes before it started shifting weird and throwing a code again.. almost seems to be slipping... I still have to check fluid level again and scan the code again but any suggestions? I have an apt to go to the tranny shop this week and would like to avoid the big bucks if possible.
View 14 Replies
My 99 E350 with 7.3 power stroke quickly lost power while on the highway today, bogged down and died. I couldn't get it restarted so had to have it towed home. I tried getting it started at home but it just pumps out white smoke out the exhaust. I got it to fire and run for a minute on a mixture of starting fluid and wd40 but wont stay running. Some background info, I checked oil and it was low but still registered at very tip of dipstick so I topped off oil level and still no start unless I give it a mixture of starting fluid and wd40. Batteries are good and cranking fast. Truck has 355,000 miles but very little blow by and prior to this had plenty of power and didn't have to use the block heater to start it thru the winter even when the temps dropped down to 12 degrees in January.
One thing I did have an issue with this past year was an intermittent cutting out while driving where the engine would instantly shut off but as soon as I tapped accelerator pedal it would start running again like nothing happened, wouldn't even last two seconds and it was running again just like shutting off the key and turning it back on and when it would do that the "Wait to start" light would come on and gauges would drop like key was off but again it all went back normal as soon as I hit a bump or tapped the accelerator pedal and it never lasted more than a second or two and never had to pull over, just tap the pedal or hit a bump and engine would kick in and run fine so not sure if that's related to whats going on now or not.
View 11 Replies
I have a 2003 Hyundai accent that was not shifting into higher gears about (45 mph) max speed. I took a transmission out of a 2005 ( same engine bad unibody) and put in the 2003. Making sure the torque converter was in all the way. Now I have no gears at all, no park, nothing. But the car does start. I went to the salvage yard and noticed that all the cars like it (hyundai) had no park either. So I must be missing something electrical right?
View 11 Replies
Truck is an early 1999 F250 Super Duty ext cab long bed, ZF6 swap. 164k miles on the dash, has the newer injectors and hpop from what I was told. It does have a 6 position switch, I typically keep it at the daily 70 horse gain tune. I do not beat the truck often. I don't tow often either.
Truck always took a few seconds longer to start than other 7.3s I have seen. So two days in row, after 8 hours of sitting in the sun, my truck did not wanna start right. Took about 5 minutes of cranking both days to get it to start. Then today on my way to work in the morning I started truck let it idle, everything seemed fine, Started driving and the engine just didn't sound right, but I figured maybe it was still a little cold. Continued driving, and it stalled out ( zf6) , I tried pop starting it but that only got me another block or two, after 10 minutes of cranking I got it to start up made it a half mile it shut off, same thing started and got it home. It cranked longer than normal but started at home after it I turned it off.
At work now so I have yet to check anything. Replacing CPS after work No smoke out of tailpipe, It is getting fuel, I checked the filter. I am no master mechanic, I do basic maintenance like oil changes, brakes, filters and censors my self. Anything more intensive I have not done. If it is not the CPS what else could it be, and how would I go about checking?
View 7 Replies
Changed CPS,EBPV sensor and tube,replaced IPR&fuel pressure regulator,batteries 100%,HPOP full,oil level full,fuel in bowl and lift pump runs(have not tested pressure but has good flow).After replacing IPR truck started quickly and idled for 15 minutes,decided to try a test drive ,truck stalled after reversing 10 ft as I shifted into first gear.Now no start!!Losing my mind.
View 4 Replies
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
View 10 Replies
Ok, so my 2002 f250 died on me last Tuesday out of the blue, pulled it home and found fuse 23 I think ECU power was blown. I removed my Hydra, and put a new fuse in it and all seemed well, then Friday evening on my way to dinner was driving along and truck shuts off like someone turned the key off. I replace the Crank sensor, even though I had put a new one in after the first time it died, which was last Tuesday, still would not start.
Pulled it home, went out Saturday morning to look at it and hit the key and it fired right off. At this point I don't really know where to look, I wiggled every wire I could find while it was running Saturday and no change, but it does seem to have a miss in it while it is idling...... I am not sure where to start looking....
View 7 Replies
My 01 4x4 F350CCD was having this "issue" where, after leaving it plugged in all night, I would start it up with no problems but then after idling for maybe 15-30 seconds it would just fade out and shut off. The first few times I would hit the key again and it would crank for an extended period but then refire and it would idle normally. Eventually I learned that if I held the idle up at around 1000 I could see the rpm drop slightly after starting but it wouldn't shut off.
About a week ago I started the truck and wasn't paying attention and didn't hold the throttle open and the truck shut off. This time after cranking it (probably way to much) it wouldn't start at all. I changed the fuel filter but that did nothing. I also notice that the tach does move to around 500 or so when cranking. I have not changed the CPS but a new one had been installed in May 2015. The engine is cranking but there is no white smoke or even attempt to fire.
View 11 Replies
Another "no start" issue... The details:
- 2002 F250 7.3L
- Rosewood stage two single shot injectors (rebuilt 1 week ago).
- DP Tuner
- Brand new OEM IPR
- ICP about two months old (OEM)
- New UVH's installed about a month ago
The issue: After installing the injectors and driving about 30 miles the truck died and will not restart. Had to have it towed home. Thus far, I've unplugged the ICP, switched out the CPS with a known good, replaced the IPR, checked the hpop simply by removing the fill plug on the top of the reservoir and gave it a quick crank - oil definitely came pouring out, removed valve covers and plugs to verify oil in the high pressure rails. Oil dummy gauge climbs after about 5 seconds of cranking and seems to hold.
Hoping it's not an injector failure as I just had these reworked. EDIT: Forgot to mention, not seeing any white smoke while cranking. Fuel bowl, full of fuel and fuel pump was replaced this past spring. What to check next? Tried taking a snapshot from a video to show the readings. The ICP seems low, and when unplugged shoots up the 2500, but still no start.
View 14 Replies
Driving along today my trans started doing some weird stuff. It lost all gears. Forward and reverse. If I turned the truck off and let it sit a while it would go again for awhile then loose drive again. When I got home I checked fluid level and did KOEO o/d off and back on. I drove it around the block and it seemed ok, so I went on my way. After about 20 min I noticed the OD light flashing. I checked codes and It had P1754-ccs.
View 14 Replies
Ok, the swap is all done and I have an engine in the truck that has compression in more than (7) cylinders.
2002, 7.3, 4wd - ~120k miles on trans. Fresh fluid (Mercon V).
Put the gear selector in reverse and it goes right into gear with the normal tug and functions as it should. Put it in low gear and it also appears to work fine. But, when selecting '2' or 'drive' it feels almost like its engaging 2 gears at once?? There is limited forward motion and it feels like the brakes are on. I have not driven further than the driveway yet, but I have a long driveway...
The OD light does not come on. I am not getting any codes from AE, but I really don't know how to use it for transmission stuff (I've been using a different scan tool that I no longer have).
We have not put the bed on the truck, so no tail lights - but 3rd brake light has new bulbs and was working (didn't check this AM though... )
I have a couple other codes, CEL, 'check gauges' and no tach. Gonna start another thread for those issues, I'll put a link here in case its related.
View 14 Replies
I have a 2002 F-250 with a 7.3.
I have been having a no crank, no start issue off and on for a while. batteries are new, cables are new, connections are clean, and starter has been rebuilt and checked. I bought a "starter relay" which i thought was the top solenoid in this picture. I also replaced the lower solenoid in the picture. The bottom solenoid was replaced with what im sure is the correct replacement. The upper I think is wrong. It started but then shut down and will not restart. The upper solenoid also was very hot after it shut down.
Long story short what is the upper solenoid for? Im assuming its not the starter solenoid. If so where is the Starter solenoid on a 2002 7.3?
View 14 Replies
I just got a 02 f250 lariat 4x4. 7.3. the dimmer on the dash will not work. The light switch was falling apart any way so I replaced it with motor raft switch. Didn't fix it I checked the fuses for the dash and lights. Can't find anything. It does have an aftermarket CD player and those light work with switch. Also it has the mirrors with turn signals and run lights. Neither works power mirrors work fine but no lights. On either side.
View 9 Replies
I have a 2000 F350 7.3 213,000 miles. Manual tranny, 2wd. It is my daily driver.
No issues until 2 weeks ago I pulled out and began shift gears when the engine died and I completely lose pedal. The engine does not shut off it goes to idle and the lights and power are fine but I quickly lose acceleration. After a couple seconds and a few pumps on the pedal it comes back. The problem is intermittant. Until yesterday it was only in the morning but then happened on the way home from work. Thinking ti was water in the fuel I used an additive to cure the water.
I changed the fuel filter just after I bought it in April of this year. I know there is a Injector Pressure Sensor that could be the culprit. EGR?
View 14 Replies
Put in my new S&B intake today and when I stomp on the gas I am getting a loud shuddering noise from the intake when I change gears. Also sounds like a squealing sound sometimes. Doesn't sound like other trucks that I have heard. What that could be?
View 14 Replies
(2000 F-350, 7.3L, 205k miles) Over this weekend, I noticed while driving mostly in the lower gears, that there was a slight hesitation with the throttle pedal depressed about half way or less. Seem to get worse as the day went by, but no lights or anything came on. Changed the fuel filter and added a fuel injection cleaner to the tank. Checked the oil and it was low, so I filled it to the correct amount.
Drove it around the next day, and it seemed to be good, until it warmed up some, and continued to hesitate. The hesitation seems as if it's not getting constant fuel, and the truck jerks a little. Once you get up to over 2000 rpms, it goes away. Looking up other reviews on similar issues, most have pointed to the throttle pedal sensor and just changed out the pedal assembly. Before I take it that far, I wanted to see what was the corrective action.
View 3 Replies
I had been waiting to fix my explorer for a long time. The "previous owner" I will call him knowingly sold me a vehicle with a bad tranny without disclosing it... long story. To get to the important part, it had the common 2/3 shift flare. I dropped the pan, filter, and valve body, making sure to use a template and put the bolts where they go. Then i took the valve body to the work bench and replaced the gasket, which was surprisingly not blown. After more looking around, I realized the previous owner had already had the fix done. I tightened the EPC 1/4 turn and reassembled the tranny. When i started it, it was stuck in first gear. PRN21 all went forward (park just revved a bit due to the park lockout.)
I tore it back apart and found that the plunger on the side of the valve body was stuck in the 1st gear position. I pushed it back out and cleaned it up so it moved freely. Then I reassembled the tranny using new fluid again.
After that the tranny was stuck in neutral. I dropped the pan again today, and tightened the valve body bolts and made sure my solenoids are tight. Filled it back up slowly with the engine running. It shifted into gear for a second (tried to go forward while it was in reverse though). Then it was again stuck in neutral in all the gears again.
View 2 Replies
I have a 2000 7.3 f450 having some electrical issues. When you turn the key on sometimes the dash will start ticking and left side light flashing...engine will turn over but it won't start. The ticking is coming from under the hood relay 32 (you can hear and feel it clicking). Book says its injector driver module power relay. A lot of the times it will start fine other times it will be running and just die (prob because of this issue) happened once when I was driving.
What to check here already replaced the relay still have the problem.
View 6 Replies
I have a F150, 2nd 4.6, 122,000 miles. No forward gears. When put in drive, you can feel it trying to engage, but doesn't engage completely. Reverse is a solid engagement. Replaced filter and fluid, same issue.
View 12 Replies
