Ford 7.3L Power Stroke (1999-2003) :: Trans Not Shifting Into 1st Or 2nd / Truck Acts Like In Neutral
Jul 27, 2015
So I put in new clutch yesterday. Reverse works, granny works, 3,4,5 work. ZF6 manual. But when I try to go 1st or 2nd. Its as if the truck is in neutral....what should I be looking for. I bought the truck having only knowing the clutch was completely shot, was not told about this 1&2 gear issue....
Do I need to pull the trans out again... or is there something I can see or adjust, because from what i can see where the shifter connects there is no adjustments. Is it probably a gear selector fork...or connection that took a crap. when moving in granny gear i did not hear any irregular noises....
View 2 Replies
Advertisement
My friend has just brought a truck and has lost 3-4 gear in the auto trans. We have the PO782 code coming up. Is there something in particular we should look at first.
View 2 Replies
2000 powerstroke 4r100 transmission. It has 155k just had it rebuilt and the shop is having a night as am I. It was shifting hard and the o/d off light would start flashing after you drove it a while. Its still doing the same thing and the shop checked the whole wiring harness and replaced the accumulator twice believing they got a bad re-manufactured one. The only code I can pull is a 605 pcm read only memory error. Could the cause be a bad pcm? The shop doesn't seem to have a clue at this point and I'm out 2500. IV taken it back twice now and Iv driven it a total of 35 miles since the rebuild...
View 1 Replies
When taking off the 1-2 shift and the 2-3 shift the truck will go into a neutral state for 2-5 seconds. when this occurs, the rpms will rev since your foot is on the accelerator. Once you let off the accelerator the rpms come down and the gear will catch. I have had the truck in the shop a few times without any luck. part of the problem is no codes are thrown so the dealer has no clue what to look for. This is extremely dangerous when in my case i pull out on a 6 lane hwy with 55mph speed limit. Ford more or less said to pound salt until a code is thrown or until something else happens. this nearly caused a nasty wreck 2 weeks ago.
View 14 Replies
My excursion's trans is slipping on the 25hp tune up high in the RPM band and shutters when up shifting. I have dropped to stock most of the time, but I know i am on borrowed time.
I had a JW trans in my e99, and there is no question on the durability and performance of the transmission. The price has gone up a lot, but that's maybe not the big issue.
I live in the mountains and spend a lot of time pulling and just driving in that 40 to 60 mph range over mountain passes. That is basically where I spend ALL of my time.
The distance between 3rd and 4th is driving me CRAZY! I have researched everything from swapping to a manual, to PCS controllers, to trying 4.11 gears, to overdrive units.
Swapping Manual: ZF6 is the obvious candidate, but I have read the swap is not probably something I have the skills or tools to do. I have also read that the performance of the ZF6 is sub par. But it seems like it would give me my 3.5 gear that I am looking for.
PCS Controller: Looks cool for a way to have control besides using the tree shift. Maybe a compromise on not swapping in a manual.
4.11 Gears: I get pretty excited thinking about the low end torque etc. I go off road almost every week, and like I said, I hardly go over 75 mph. But once in a while I do. Right now, the truck turns about 2300- 2500 rpm at interstate cruising speed. Looking for 4.10s rpm in that range to compare? Also, how bad of a fuel economy hit would I take? What is the cruising rpm of 4.10's between 60 and 65 mph, or in general what is the rpm change?
Overdrive Unit: I have always been interested in more gears, but I read about someone who installed one behind a 7.3 and didn't have they great of results. To the point where he said it wasn't worth it.
View 2 Replies
I bought a 1997 f150 with 160l miles on it. It is a 4x4 with the 5.4 v automatic. While I'm drive and in 4th and 5th gear, the tranny shakes the whole truck and then shifts hard! I check the fluid and it's still good and red but looks like there is to much. I'm planning on removing some and adding some lucus additive in it. What could cause this???
View 8 Replies
I have a 04 6.0 and lost with it. I parked it the other night and in the morning I went to start it and it acts like it's only running on half the cylinders. I haven't had any issues till now so I replaced fuel filters and air cleaner is fresh but no change. It is not throwing a check engine light it isn't smoking excessively. I don't know where to check next.
View 5 Replies
Last week I hauled my camper (2000 Thor Citation @ about 10,000 lbs) to Moosehead Lake. On the trip to and from I experienced a few problems. Tow/haul was engaged all three times. Trucks got just over 90,000 mi.
1) When shifting, the truck would occasionally stutter, like a gas engine when it misfires. Seemed like it would usually happen when transitioning from a slight down hill to an up hill.
2) Once, after a long up hill pull, as it crested the top, the truck slammed into the next gear, hard.
3)Once, going down hill, the trans wouldn't shift into O.D. until I took the rpm's up to 3000 then let off the throttle. No, I did not touch the brake prior to this.
Figure the tranny's gonna need a rebuild soon. What kind of upgraded parts does the wise and all knowing FTE wizards think I should be looking at? I tow the camper a lot during the summer so I want a trans that will hold up to the abuse. I'm probably stuck with this thing for a few more years.
View 14 Replies
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 Replies
Have to get rpm's over 2k before trans will engage, then in between shifts I either have to let off throttle or let engine rev over 2k to get trans to shift...
View 3 Replies
I'm getting a sound every now and then of what sounds like i'm running over rumble strips on the side of the highway. I'm guessing it's the trans grinding. Any thoughts?
View 8 Replies
I notice my trans temp gets really hot fast. For instance just moving my trailer from front of my house to side yard makes temp go to 250. Without any load and driving a couple miles it does the same thing. It's been doing it since I installed the trans temp gauge just trying to figure out what's up.
View 14 Replies
I bought this truck with 200000 miles and its been flawless, its now 900 short of 600000.. I use it to haul everyday.. nothing heavy mostly a car or truck and every once in a while a skid steer. I got 560000 out of my trans, i take it easy. lol
at 350k I installed a Jw valve body drilled pump, tripple disc converter and solenoid pack.. at 560k it went, i pulled it and brought to a guy i trust as much as you guys trust BDS.. Ive had what Ive called a vibration since day one, could be a shudder, could be a shimmy.. what ever.. I brought it back and he says nothing would do that from a trans, so I went through drive shaft, new t case ripped apart rear end and its still there and I have just been dealing with it.. about 2 months ago it started acting up in first. when I pull down to drive I get the normal bump and start to go, it feel like the truck slows, then another bump and it climbs normally with the shudder.
took it back and he said maybe a stuck valve in small VB, so I pulled it and went down there and it was fine, I reinstalled and still does same thing. I then put a pressure gauge on it and it swings as it should sits around 70 psi and will climb, only in first it will climb and fall back to 70 like a switch was flipped, and the rest of the gears bleed off slowly or normally.. He then said it could be the big valve body, so I swapped that one out with another and no real change, maybe its a bit more noticeable.
I am at a loss. Could this be loose feed bolts? Could the shudder that I can feel at most speeds be the 1 gear slipping a tiny bit all the time? I am told that first gear is always on.. this truck has been a dream until this trans issue..
View 2 Replies
I've searched, and gone back through my computer history and can't find it. I have seen a thread here which Mark contributed too which said what the max temps were and for how long etc. I know book is 230 and optimum is around 165 but there was some degree of play in that.
View 8 Replies
So my transmission drove perfectly fine I just wanted to put an upgraded torque converter in especially after driving a customers' truck with a low stall converter. I know their not like for racing or anything but it's a work Truck with some mods to the motor nothing crazy. So I went ahead and bought a low stall triple disk converter and I drove around the block fine and went to go on the freeway and got into fourth but lost it as I hit 75 (was not flooring by any means and had it in the stock tune) now it will not go past second gear. Once it did this the o/d off light started to flash and I decided to do a stall test.went to 1800 in a Second. Suppose to stall around 1200-1300.
2000 f250 7.3 powerstroke dp chip stage 1 camshaft and 180/100 injectors coming at some point but stock for now
View 3 Replies
Well stock trans went two weeks ago so warranty company had another stock one put it (4r100). Finally got the truck today and I noticed my overdrive was flashing. I have no issues though shifts fine speedo works Rpms are normal I checked fuse 19 under the dash that's fine so I'm lost
If I turn the key on I can use the button like normal but once I drive it just flashes. It works but flashes .
View 7 Replies
So just got a new pcm installed since i fried the last one anyway. I had a new trans installed almost two weeks ago factory 4r100 now i have a p0720 code. Id take it back to that dealer.
View 8 Replies
1999 7.3/4r100 4wd with the rattling torque converter.
I bought this truck 10-11 years ago to use as a tow rig for my landscaping company. It has been a great problem free truck, I have done brakes a few times, a water pump, ball joints but no issues with motor/drivetrain.
I don't know the history of the trans before I purchased. Ford didn't have history of it being replaced and even now it still has all the labeling on the case. I would have thought it would have been washed off in a rebuild. Again I don't know. When I bought the truck it shifted nice and crisp, having owned trucks before it made me think it had been rebuilt but this was my first and only 4r100. Other trucks are ZF6 manuals.
Anyway 10 years and 100,000 miles later it still shifts very crisp and fluid, has been changed a couple times, is nice and cherry red. I added a 6.0 cooler, temp gauge and filter. Never see the temp rise and haven't seen much in the filter.
About 25,000 miles ago the TC started to rattle, a known 99 problem. I figured surely the trans would go and I would do a rebuilt from Ford. It keeps going though so being a work truck I have kept running it.
A couple weeks ago the starter just spun and wouldn't engage. I pulled the inspection cover and noticed some missing teeth on flex plate. Got it to start my turning crank bolt a bit to good teeth and the starter caught. Now we are carrying a breaker bar and socket. It has happened a few more times so I need to replace flex plate.
Question is, since I need to pull trans to replace flexplate, should I replace TC (I would like to get rid of the noise)? Some people have said I will be replacing trans in a couple months if I mess with it. They say just spend $3000 on a rebuilt now with a converter. Not trying to be cheap but hate to just dump this trans that is still working great and has served me well.
I have replaced many transmission and done clutches in many trucks so I am familiar with the steps of removal and installation, just stuck on what I should do.
View 14 Replies
2001 7.3 auto, 2wdr, 291,000, Transmission sometimes shifts hard from 1st-2nd, 2nd-3rd. Problem started after I found trans dip stick tube broken and loss of fluid. Anything I can do without going to a shop. I've replaced the Broken Tube.
View 2 Replies
Iv heard a few things about changing the valve body. I tow a trailer so was wondering on pros and cons of changing this. And also what brands are recommended.
View 5 Replies
I have the 4r100 transmission how do I bypass the safety switch? Also what are your thoughts on starting the engine with the transmission out? I know to bolt the spacer plate to the engine.
View 7 Replies
