Ford 7.3L Power Stroke (1999-2003) :: Sluggish / Slow Response On The Road - Throttle Surge
May 12, 2017
7.3 2001 model starts ok at 32-35 F. Feels a bit sluggish / slow response on the road. Reach a hill after 3-4 miles. Engine temp then beginning to go above low level mark. 100 meters up the hill, going around 30 mph there is a sudden surge in the throttle although my pedal is steady. Going back a few minutes later, on flat ground at bottom of hill and with no accelerator pressure, the engine suddenly stalls. Starts fine again after I stop. The same history actually repeated on two separate days recdently on the same hill. CPS is recently replaced. Had some jerking before that, but not the behavior explained above. Current CPS is Delphi light grey. Recent fuel filter change and oil change as well
View 14 Replies
Advertisement
My 7.3 has no throttle response, the code reader says pass, and there are no codes, would it do this even thow it has a bad TPS?
View 4 Replies
I have a 99 F450 with the 7.3L in it. I brought it home the other day and parked it. Later I went to do something with it and I had no throttle response at all. I checked the wiring going in and coming out of the throttle position sensor. I have approx. 5 volts going in and the voltage sits at about .5 volts and rises as the accelerator is depressed on the outgoing wire. The other switch on the pedal is open and does close when the pedal is depressed, so it seems those are fine. I'm not sure what I'm supposed to have on the 3rd wire that goes to the TPS.
I have a Bully Dog tuner and it shows an exhaust back pressure sensor error and a couple of voltage errors to the accelerator pedal. I read somewhere that someone had an exhaust sensor short out and it starved the accelerator pedal from voltage or something like that but I do have good voltage at the pedal going in and out. I ordered a new sensor and tube.
If the exhaust pressure sensor was shorting out and I unhooked the wires could that make the pedal work if the sensor was the problem or would the accelerator pedal not work at all without that sensor being connected? (The old tube was somewhat plugged up and I saw it had a small rust hole in it)
If it's not the sensor, what else can I check? Where can I check under the hood to see if the wires from the TPS are getting power to where they need to? I assume they go to the computer and that tells the pump or whatever to give more fuel.
View 10 Replies
I've been having rather slow throttle response with my 6.0 f250 diesel at lower RPMs. Obviously, this is to be expected to some point.. Whether I'm cruising on the highway or through the neighborhood, if the truck is at lower RPMs and I try to accelerate, it doesn't want to. In order to get it to accelerate, I have to press the gas down enough to downshift it then it'll take off.
The truck doesn't have a loss of power at higher RPMs, it takes off like a bat out of hell. I've put 175CC injectors in, tuned it, power max turbo, EGR deleted / studded, etc. It's almost go out with acceleration, or go turtle power with acceleration.
Oil pump was replaced a couple years ago. This problem existed through it all, and it's rather annoying. The truck doesn't want to produce any low end power. If I try to hit the gas enough to accelerate but not enough to force a downshift, I'll just blow smoke, spool the turbo, and barely accelerate until I down shift or push the truck through it. Turbo PSI is roughly ~15ish-20ish during the sluggish transition.
View 14 Replies
i got a 99 F250 powerstroke with 148K on its clock, i have a couple issues that i cant find a definitive answer for, 1 just started recently, Its an automatic and when it shifts into third around 40 mph the rpms drop to 1200-1300 or so, its done it since i got it, but recently it wont accelerate like it should or used to do, i have to put it down and make it downshift to recover.
Now I have no CEL. and it is still running perfect just has very little power, I do have a 4 inch turbo back exhaust and have a TS 6 position chip with i usually run in +50hp mode, but it does this in all positions. Now issue 2 is when its 30 degrees sometimes it will not start. It'll turn over with now fire. but if i cycle the key again it'll fire right up like a champ? It has a 4 month old starter and batteries and a month old alternator and i have tried several CPS' and Contently check the connections.
View 2 Replies
I own a 2000 F250 7.3 Powerstroke 4x4. The only aftermarket engine modification I have is a Tymar intake. The problem I'm having started about 6 months ago in a very erratic fashion. I would pull up to a traffic signal and as the light changed to green, without warning the truck would have no throttle response. The engine was running fine; there was just no response as I stepped on the accelerator pedal. Usually when I put the transmission in neutral, revved the engine a few times, the throttle would come back on line. This happened 4 or 5 times over the summer and then went away completely until today. Today it came back with a vengeance. At one point I had to shut the engine down completely to restore throttle response. It's a bit unnerving when it happens in the middle of a busy intersection. I was told that it may be the throttle position sensor. Does this sound correct and does it need to be replaced?
View 14 Replies
I have read many different threads regarding the TPS sensor on the pedal and EBPV deletes on the E99 7.3L Powerstrokes. I am trying to troubleshoot some issues with my E99 7.3L. Usually on cool mornings and after not being started for awhile the truck will seem to be stuck in an Idle. This is an intermittent problem that doesn't always happen.
I cleaned the connections to the Tps and the IVS sensor and put them back in. No luck. On another note I am also seeing a reduction in fuel mileage and power like the truck is being restricted. I don't know if these symptoms are related or possibly their own issues. I am troubleshooting and possibly thinking it is the EBPV system that isn't working correctly. Considering doing an EBPV delete with a NON-EBPV Pedestal and Flange.
View 12 Replies
I just changed timing belt all accessory belts and water pump on my 2001 Hyundai Elantra. Now the check engine light is on and it is sluggish in throttle response. It sounds smooth. I was quite sure I had the cam and crank marks dead on. I turned it 2 revolutions by hand and they both looked dead on before I started it. If I were off 1 or 2 teeth would that be the cause? And if so how do I fix it? Also will it hurt it to drive it that way?
View 2 Replies
2003 f250 6.0.... recently did oil cooler,hpop,ipr,icp,fuel pump,egr valve, rebuilt the turbo.... when around 35mph truck seems sluggish and doesnt seem to pick up quick untill i floor it an then hauls butt.. vgt reading at idle is 62% and when floored around 30 to 35%.. fuel pressure is 63psi.. ipr is around 60 to 70% when floored and around 25% at idle. Hpop reading when floored is 3000 to 4000psi and idle is 624psi....
View 14 Replies
Experiencing sluggish throttle response on the EFI Ecoboost? I have had several incidents where I'm needing to change lanes fast and the response is a dead second or two before the motor catches up to the throttle position. Then, it rockets forward at full throttle to catch up. By that time it's too late to change lanes and I have to be on the brakes hard to keep from rear ending the guy in front of me. I'm coming from a carburetored Toyota Tacoma that was far more responsive (minus the power) then this truck. I never felt hesitant to jump on it and go. Now I feel like my life depends on waiting until I have all day to change lanes, make a left turn or pass a slow moving vehicle on a two lane road. Is this something the dealer can adjust?
View 14 Replies
I have a 03 6.0. I just had all the injectors changed a new fuel pump, spring in the regulator and fuel filters ouch. The truck runs great but I get a puff of black smoke if I get on the throttle going down the road it seem to clear up as soon as the turbo spools up. I that ok or do I need to take it back to the dealer?
View 1 Replies
So while driving just now the truck went down to idle and no matter what I did to the gas pedal the throttle would not change. The truck didn't die but would just sit at idle. It was like the gas pedal wasn't connected. About a minute later it surged a little and then I was able to drive like normal.
History- last week while at a red light the engine surged and then almost died. Light changed and I hit the gas....and stayed at idle...then died. Restarted and died two more times and then just drove like normal. Changed fuel filters and and checked fuel pressure. Under boost it was 38-40 psi. Idle it was 45. Cac tube replaced due to cracks.
View 14 Replies
I am a dedicated Ford truck owner. Both vehicles I have had are both F150's. My first one was a 5.4L v8 03 and my current is a 5.4L v8 06 4x4, seen below.
When I bought the truck it was straight piped. I went ahead and did a GOTTS mod on it. The truck also has the factory tow package. I replaced the spark plugs and engine oil (Amsoil High Mileage). I did a couple basic things like putting in the light bar and replacing the headlight housings. Other than that it it pretty much the same as when I bought it. I cleaned the throttle body and sensors, using the proper cleaners. I ran two cans of SeaFoam through as well.
With my last truck, I 'flushed' the transmission (not a actual flush, but I changed the tranny oil about 7 times in a short period of time). A buddy suggested I do it, as it was a DOT truck and maybe wasn't treated the best. It was a automatic, just like my 06. Would that do any actual good?
I have noticed that truck has a spongy/delayed throttle response. The engine idles normally and there are no codes being thrown. I had a similar issue with my 03 but it had a cable to the pedal and I just had to tighten that up and it was better. Perhaps because of the straight pipe and GOTTS and no tune?
View 8 Replies
I have 01 F550 6spd 4x4. sounds rhythmic, smooth at idle but just over 1200 is a pattern surge but doesn't sound like one cylinder, cel is off, ICP and pigtail changed as it was leaking , no change. From what I've read duty on ICP and IPR should be about same % I've included the codes I've gotten, I have the epc disconnected right now as I thought it was a wastegate issue, checking the ICP plug next,anything I've missed? It had a cyl 8 contribution at idle which I hear is common? Will changing CPS work with that one? Think it's a grey one. There's no water in bowl I replaced filter, since replaced ICP, pigtail, and bleeding fuel bowl and new filter the codes are gone but still misses, will be checking uvch, injector buzz test showed no faults. Old diesel guy said to flood with Stanadyne fuel treat?
View 9 Replies
Decided to try a new wheel to see if I can stop the surge during hill climbing with our 5er. Old wheel looked great with no dusting or nicks. New wheel sure has a whirl when it spools up, but sounds cool. Haven't pulled trailer since swap yet. Truck still only has 85k on the clock.
View 7 Replies
I just recently got my truck back, My father and I switched vehicles due to need and distance's being driven. 2005 F350 6.0, 164,000 miles
I couldn't wait to drive it again, I spent hours detailing and cleaning. Well I go to start and noticed it struggled to start, and didnt seem to be idling right. I looked under the hood and it was leaking fuel from the Regulator. I left it parked and never drove it since he last did. I read around on these forums and I bought the blue spring upgrade kit.
Now I notice it shakes at idle a lot more than it used to, pretty bad at times. Then upon driving it shakes even worse upon acceleration attempts, and has very poor throttle response. I have to put it nearly to the floor and even then the acceleration is nothing like it used to be. Most of my trip was highway at 60mph, and anytime it would start climbing a hill it would shake pretty bad with the acceleration. When i let off the gas to slow down before braking it stopped the shaking.
So I read around on here and I went back and used the factory bowl and valve for the regulator, still had the issue. Next I went back and replaced the blue spring with the original, still have the issue.
I just checked the FICM and it is reading between 48-49 during key on, cycle, and cranking.
Batteries are great
Alternator only reads 13.6 at 2k rpm idle, but have not had charging issues.
My father says he never noticed anything wrong with it other than it occasionally missing out. But I don't see how changing the fuel pressure regulator would have caused this. Especially since I tried every combination of oem and aftermarket parts, ensuring that all the connections and parts were installed correctly.
View 14 Replies
So I was driving to work and the truck lost throttle response. There was very little of it! Came to a stop then it didn't barely want to move, pulled over then it died on me! No clue what to look at! 2005 6.0 232k miles
View 14 Replies
I just completed installing rebuilt injectors in #2 and #4. for the 2nd time. The first set had failures with those two. After assembly, the engine runs rough which is understandable considering the air introduced. I can run the RPMs up while in neutral or park, however; there is almost no throttle response in drive or reverse. It will barely move and only slightly raises the RPMs. I am unable to drive it to get the air out until this particular issue is solved.
Prior to the tear down for #2 and #4, the throttle response was fine.
Current Codes:
P0272 - I am hoping this would go away once the air is gone.
Software:
AE w/ Ford Bundle (New to me)
Buzz test is fine
Power balance looks great
FICM logic and power are good
Skills:
DIY w/ limited electrical knowledge
Recent Mods in last 300 miles:
New heads
ARP studs
ICP
IPR
FICM w/ Atlas 40 from FICMreapir.com
Injector harness
HPOP
Chemical flushes
Oil Cooler
Leak Proof Ball Tubes
Stand Pipes
8 Rebuilt Injectors
Batteries
MAP Sensor
New Turbo w/ updated supply and return
All associated gaskets and orings replaced with the above
All OEM where available, except injector rebuild service
View 5 Replies
2001, 7.3 sometimes surges slightly on takeoff ??
View 1 Replies
2007 F350 6.0L 230,000 miles
Yesterday, while driving home from a weekend out of town trip, all of sudden lost throttle control. Just went to idle while at cruise speeds, could pump pedal and no response. Then got pedal control back and seemed to run normally.
This happened several times. Hubby suggested moving the adjustable pedal which I did slightly. Although I was not using the cruise control, we had a sense that maybe it was engaging??? So I hit the off button a couple of times. After these two interventions, drove the last 80 miles home with no further incidents.
Today, we checked codes and had a PO231, Fuel Pump Secondary Circuit Low. I don't think that is our problem with above based on research, but we will look into fixing that too. We are thinking TPS or a position sensor on the accelerator pedal. We could replace those easily ourselves.
View 14 Replies
I am fairly new to working on diesel engines. I was towing a camp trailer and got a P0299, Turbo Charger Underboost engine code. I never gotten any other codes other than this one when towing. I decided to pull the turbo and clean the vanes. Everything seemed to go back together good but now I hear what sounds like an air leak coming from the turbo area. The boots on the intercooler pipe are in good shape, I only loosened the clamps at the intercooler and the turbo. Left the boots on the pipe. I have tightened the clamps around the exhaust pipe connections with no change. I also seem to get a slower response from the turbo and possibly not as much psi as normal (according to dashboard gauge). I have driven the truck five or ten miles trying to work the turbo and have not gotten any engine codes to this point.
View 7 Replies
