Ford 7.3L Power Stroke (1999-2003) :: Slower Cranking Time And Took A Second Or 2 Longer Than Normal
Sep 12, 2016
I have a 2002 F350 7.3 with 76,000 miles (still a baby) ... about a week or 2 ago i got in my truck and went to start it like normal, except instead of whipping over and firing right up in the snap of a finger, it kinda had a slower cranking time and took a second or 2 longer than normal. My first thought was maybe the battery's, BUT there basically brand new !!! not even a year old !!! ... so i figured maybe a starter, but i just left it as is, it still ran normal after firing.... Until this morning, I went to go start it and it cranked over 3 or 4 times real slow and would crank any more, it did this to me multiple times. Its acting like dead batteries so i put a jump pack on it, no change. I am thinking maybe a starter ....
View 8 Replies
Advertisement
About 7 months ago my truck started cranking longer than normal to start after sitting for more than 2 hours. This went on for about 3 weeks, then it started normally again. (By longer crank time, i timed it between 5-7 seconds on average. Normal is about 2 seconds). Now it has started doing this again about 4 weeks ago. Now I'm thinking HPO slow leak. Yesterday all is good again. What should I be looking for as a starting point to fix this permanently? When it cranks longer, the icp stays at 0, the ipr goes to 77%. Then it just fires off. No slow build of pressure. You can see all my mods and updated parts in my sig. I wonder if one of the new dummy plug o-rings is starting to give up already after only 15k miles. (Batt voltage is at 13.9-14.2, ficm is at 49.5 steady).
View 5 Replies
I just started having an issue on my 01 7.3 f350 with 203k miles, it will crank much longer then normal to start. If you shut it off then try to restart right away it starts normal, if you wait 10 minutes long crank again. if you shut it off and turn key back on but don't start it you can wait an hour then start right away. IDM bad? Vacation in 2 weeks and I would like to get this fixed first.
View 14 Replies
I got a friend of mine that owns a 2000 F350 7.3 with around 280,000 miles. He said that the past 2 days its been turning over longer then normal before it fires. Once started, engine runs same as it always has. No sputtering or hesitations, idles fine, etc. However today, he drove to work, shut it off, then went to start it back up 10 or so mins later and now it will only turn over. Said he's getting fuel and compression is good. Unfortunately i dont know much about Diesel engines.
View 2 Replies
I have a 1999 f250 7.3 psd. it cranks and will not start, it use to crank for a bit of time and then start and now it refuses to start. If I leave the key in start position for like 30 seconds it use start and now it wont. I am thinking it is something with the glow plugs?
View 8 Replies
I have owned several 7.3's and I have never encountered this issue. I recently picked up a 2001 7.3 with 200k miles on it. When I bought it I knew the glow plugs were going, I also knew it accelerated slow. I went ahead and replaced the plugs, valve gaskets, and added a heavy duty glow plug relay, along with an oil change, and fuel filter.
For some reason, the truck just dose not accelerate very fast at all, significantly slower than any 7.3l I have owned in the past. It appears that I shift at about 3000 rpms and it takes a while to get up to speed. I would like to get it mechanically sound before I restore the body. I was thinking it was the ebpv? but what else could it be?
View 14 Replies
I have noticed that my truck will crank longer than normal when i park backed into my drive way but it only does it every now and then. I am guessing an internal oil leak but it starts fine cold or hot.
View 10 Replies
Been working on a no start issue on my truck last couple days. ICP was only getting to 350psi while cranking. Anyway I did the Cody test today and found bad o-rings on the #2 injector, I think. It's the front one on passenger side.
I just installed these injectors from PIS last fall and had a loud tick that sounded like a loose injector if the oil temp was below 40 deg, but went away the warmer the engine got. I never got to into looking for it because I work in my drive and it was to cold this winter, so it sat most of the winter and i drove my other truck. This spring when it started warming up I started driving it again and the tick was barely noticeable. I should note too that that side runs about 100 deg hotter than the other on the pyro's
I forgot to try re-torquing the injector before pulling it but it wasn't loose in the hole and the bolt was pretty tight. I have extra o-rings, enough to do all the injectors, but wondered if it was worth it or just do the one that's bad?
View 13 Replies
Symptoms:
- Longer cranking time when turning on the ignition.
- Codes P2293 - Fuel Pump Regulator 2 Performance, P0087 and P053F.
- When I get on it, the rpm would shoot up while the speed is increasing at a very slow rate.
At first, I thought it's my clutch slipping, but after watching this youtube video (not mine), I think it's the fuel pump issue.
View 7 Replies
This morning I went to start her up, and she fired right up and I let her warm up until oil temp got to 100F, when I realized that I wasn't leaving right away so I shut it down and came back about an hour later. Oil temp now at 78F, but she wouldn't start. Have Torque Pro running, and the IPR is going straight to 98.6% every time while cranking, sits at 14.7% with KOEO.
Truck's been running fine, recent oil/filter change (T6 10-40W), cleaned & re-installed CAC tubes/boots for leaks. All else seems good. Pulling the ICP sensor shows HPOP going to 2800psi, with IPR @ 30%, still no start and not even a cough.
The IPR is original, rebuilt once several years ago.
View 14 Replies
2001 F 350 7.3 183,000 miles.. The problem is the longer it sits the harder it starts.. when it does start it runs VERY ruff!!! it takes 10 min or so to run on all cylinders.... This is my first diesel..
View 4 Replies
Just bought this 1999 7.3 drove it a couple days now and got to walmart today. shut it off to go inside and came back out. turned on key waited for wait to start to go off. cranked the motor over but it didnt fire. i tried it again and nothing. oil is full, oil pressure is good while cranking. no rpm reading on gauge while cranking. no check engine light. batteries are literally brand new two weeks ago. Cam sensor?
View 4 Replies
I am a longtime 7.3 IDI guy with an 88 F350 crew so i know about diesels. But this is my first electronic diesel. I picked up a 2001 F450 2wd auto 260k miles. it used to be my work's truck but was stitting for a year and now i got it in "non running condition"
I towed it home and got it started by replacing the batteries and using the block heater.
As expected it took a few tries of long cranking to run the first time. runs pretty good and no smoke. what surprised me is it still takes about 5 sec of cranking to restart each time when warm too. any direction you would look with those symptoms? HPOP, IPR?
i am pretty sure the glow plugs all work because mechanics had replaced all that stuff. but i know back when the truck was last used it would still never start cold unless plugged in (even in summer).
View 14 Replies
Was driving to work about 4 miles into my travel rolled around corned and she died..... tow bill and cps she fired rite up. Ran at idle in drive way because I was a little leary for about an hour left drive way went 2 miles went to pull in to store died again. Another tow bill and 2 more cps still won't start rpm is only like 200 when cranking but sounds like a lot more. The wts light works, batteries are pretty new, cps in new...
View 6 Replies
1999 e350 has 130k and original injectors, had a minor power loss while driving that i determined was injector o ring needing replacement since the fuel bowl also had black colored fuel. installed and have been cranking for about 4 days now and am recharging batteries again. whenever i changed any injectors in the past I've refilled both sides of the oil rails although on this one I didn't. So wondering what to expect concerning the process of filling oil rails via hpop. Does have a hpx line...
View 14 Replies
What is the effect will some oil contamination is the cooling system?
Does it significantly affect the cooling efficiency? I have some oil the coolant on my boat. I do not believe it is a lot maybe a few oz, but I have been chasing some unexplained overheating issues. Will adding water wetter solve oil issues (if there are any). The other option is Dawn and several cycles of flushing the system. ie until the cows come home!
View 3 Replies
We did a Cody test and found the injector orings leaking and replaced them.
Did the test over and now hear air coming from the oil pan. Is that normal?
View 8 Replies
Ok I've got an 01 F250 sd 7.3 with 257k on it it just started talking longer to start than it should it will do it cold or hot even if I shut it off at the drive thru takes it like 10 sec or more to fire. My question is I thought about purchasing a autoenginuity to find the problem but not sure the best place to get and what model I should get.
View 7 Replies
I recently did the following work:
New Injectors
New T500 Hpop
New IPR
New ICP Sensor
New UVCH/Glowplugs
New starter
Been cranking about 15-30 seconds each time about a dozen times now. I've pulled the icp and the hp crossover and have oil flowing at each.
ICP builds to about 240 psi and at a 98% duty cycle....so I assume there's still some air in the system. I"m not getting any sense that the engine is trying to hit. Do i just keep cranking?
View 14 Replies
Background on the vehicle, Last week installed Swamps 200cc/30% injectors with a 38r. Had swamps reburn my chip for the new upgrades.
But heres the problem i noticed starting the truck was a little harder ( longer cranking ) till it would start never thought of anything since i read air gets in and can cause it but then yesterday and today its taken 30 minutes to start the truck since i have to do a trial and error.
The truck just seems like the batteries are being drained or something along those lines. i also noticed my gauges keep resetting back to blue( default color). Today I plugged a battery charger up all good voltage i charged them so both read 14v and still no start. So a couple of attempts at starting with chip in and ICP on nothing
I unhook the chip and ICP get a half start then eventually it starts. After then i can hook it all back up and it starts good for the rest of the day but for what ever reason after it sits all night it doesn't want to start up right away. I'd like to figure it out today since id rather not wake up at 4am and attempt to do this all before work each day.
I noticed that my gauges would reset to the default color after each turn off. So i unscrewed my ECU and then redid that to make sure its tight. along with making sure the chip is seated properly. after that it stopped resting my gauges. Whether that's the issue or not i cant say but ive been checking my HPOP oil level since i stopped driving it around 1400. and hasn't changed oil levels are good. I plan on starting it before I go to bed around 2200-2300 just to check and see what happens.
View 6 Replies
This is kind of strange, I have a hard start problem, when I crank it the first time, it fires immediately, kind of like a romp, but doesn't start, then when I crank again I get a lot of whitish smoke and no start. I read to try and unplug the ICP and try it. That worked, and I had oil in the connector. I replaced the ICP, but have the same problem. I still have to unplug the ICP for the truck to start. When it does start, it runs great! No injector stiction, no smoke, no rough idle, it runs and sounds great. Why unplugging the ICP is still required to start? (Only after sitting for more than 10-12 hours).
View 9 Replies
